Whirlpool Washing Machine Agitator Not Working — Solved
- Unplug your washing machine from the outlet before starting this repair in order to prevent any chances of electrocution.
- Open the lid of your washing machine. With a flat-blade screwdriver, pry the cap off the agitator and pull the lint filter out.
- Use a 7/16 inch socket wrench to loosen the bolt the agitator to the tub. ...
Full Answer
How to fix a Kenmore washing machine agitator?
How to Repair a Kenmore Washer That Won't Agitate
- Open the Kenmore washer's lid and pry the cap off the top of the agitator, using a flathead screwdriver.
- Remove the bolt from the center of the agitator, using a 7/16-inch socket and extension. Lift the agitator out of the tub and set it aside.
- Place the agitator on the floor and hold the base with your feet. ...
How to troubleshoot a whirlpool Cabrio washer?
Whirlpool Cabrio Washer Not Spinning
- Check Drive Pulley Nut. The nut that keeps the drive pulley together can become loose over time. ...
- Faulty Shift Actuator. Washers are one of the most convenient ways to get your clothes clean at home, but they can also be one of the most frustrating.
- Check Lid Switch. ...
- Drive Belt Issues. ...
- Defective Door Latch. ...
How to change the agitator in a hotpoint washer?
How to Change the Agitator in a Hotpoint Washer Unplug your Hotpoint direct-drive washer from the wall outlet. Open the lid on your appliance to access the agitator. Install a socket extension onto a socket wrench and connect a 7/16-inch socket to the extension. Spread a towel onto the floor. Remove the socket wrench from the extension and socket.
How to fix a washer that will not agitate?
Washer Will Not Spin and/or Agitate
- Too Large of Loads. A washing machine will become unbalanced if there are too many clothes being washed in the same load.
- Switches and Settings. The lid switch is located inside the cabinet near the door frame, and it's designed as a safety precaution to keep hands from entering a spinning washer ...
- Drain Pump. ...
- Belts. ...
- Motor. ...
How do I fix the agitator on my Whirlpool washer?
4:215:46Replacing the Agitator Repair Kit (Whirlpool Part # 285811) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe'll take our new bolt. Put it on our ratchet tilt the whole agitator upside down line up that boltMoreWe'll take our new bolt. Put it on our ratchet tilt the whole agitator upside down line up that bolt with a hole. Now we're ready to put it back in the washer now the agitator is ready to install.
How do you take apart a whirlpool agitator?
0:051:38AGITATOR REMOVAL—WHIRLPOOL WASHER - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you get it spun out you can just reach in from the bottom and grab the bottom part of theMoreOnce you get it spun out you can just reach in from the bottom and grab the bottom part of the agitator. And pull up probably good to reach in with two hands so you have a little bit more leverage.
What causes a Whirlpool washer not to agitate?
1:232:38Top-Load Washer Won't Agitate — Washing Machine TroubleshootingYouTubeStart of suggested clipEnd of suggested clipThe coupler can wear out over time or fail if the washer is overloaded causing the tub not toMoreThe coupler can wear out over time or fail if the washer is overloaded causing the tub not to agitate.
How do you fix the agitator on a top load washer?
0:392:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd good clean the best way to do this is with warm soapy water and a softer clock. Once theMoreAnd good clean the best way to do this is with warm soapy water and a softer clock. Once the agitator and inner drum a clean again we can replace the agitator. This just pops back in locate.
How do I fix my agitator?
0:296:51How to Fix Washer Top Agitator Not Working - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes this comes off by hand other times you may need to actually use the ratchet. Hold theMoreSometimes this comes off by hand other times you may need to actually use the ratchet. Hold the agitator down bottom in place he needs.
How do I know if my washing machine agitator is broken?
The agitator should start to oscillate back and forth, mixing up the clothes in the water. If the agitator does not move, double check that the sensor is depressed. If it still does not move with the sensor depressed, the agitator is broken and should be repaired.
What causes an agitator to stop working?
A major reason that your washing machine has stopped agitating may be that there's a fault with the drive belt. The belt could be slipping because it's loose or it may have snapped completely. If you're going to fix an issue like this you'll need to be fairly handy or call a repairperson for help.What to Do If a Washing Machine Not Agitating? - Appliance Repair Servicehttps://fixappliances.ca › washing-machine-repair › what-t...https://fixappliances.ca › washing-machine-repair › what-t...Search for: What causes an agitator to stop working?
What causes a washing machine to stop agitating?
If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. (Note: Direct-drive washing machines do not have belts.)Washer Doesn't Agitate or Spin - HomeTipshttps://www.hometips.com › washing-machine-agitate-spinhttps://www.hometips.com › washing-machine-agitate-spinSearch for: What causes a washing machine to stop agitating?
Why won't my Whirlpool washer spin or agitate?
Common solutions for: Whirlpool Washer won't spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washer transmission.Whirlpool Washer won't spin or agitate - Repair Clinichttps://www.repairclinic.com › RepairHelp › Whirlpool-...https://www.repairclinic.com › RepairHelp › Whirlpool-...Search for: Why won't my Whirlpool washer spin or agitate?
How do you remove the agitator from a Whirlpool top load washer?
0:061:02Whirlpool Top Load Washer Agitator Assembly #3951744 - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo replace the agitator on your washer first remove the fabric dispenser. You can use a flatheadMoreTo replace the agitator on your washer first remove the fabric dispenser. You can use a flathead screwdriver to help pry it off if necessary. Pull out the agitator cap.
How do I clean my washing machine agitator without removing the agitator?
1:517:15How To Properly Clean Your Top Load Washer | PartSelect.comYouTubeStart of suggested clipEnd of suggested clipTo clean this we would suggest soaking that in as hot water as you can and use either a baking sodaMoreTo clean this we would suggest soaking that in as hot water as you can and use either a baking soda or vinegar or a combination of both solution.
How do you loosen the agitator bolt?
1:134:08How To: Whirlpool/KitchenAid/Maytag Agitator Bolt WPW10076270YouTubeStart of suggested clipEnd of suggested clipOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonnaMoreOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonna have to reach down and hold it while you break the bolt. Free.
Can I remove the agitator from my washing machine?
Since it's difficult to reach down into the washing machine drum, cleaning the agitator is much easier when you can remove it. You'll also need to remove the agitator for a common do-it-yourself washer repair: replacing the plastic dogs—or ratcheting teeth—when the agitator no longer spins.
How to remove agitator cap on washing machine?
Remove the washing machine agitator cap by prying up around the outer edge with a small flat-blade screwdriver. Then unscrew the center hold-down (Photo 1). Reach in and remove the ratchet assembly. Turn it upside down and remove the snap-in retaining plate (Photo 2). Then install the new agitator dogs and retaining plate (Photo 3). Then reinstall the ratcheting assembly, tighten and pop on the lid.
What happens if your Whirlpool washer stops agitating?
If your Whirlpool washer stops agitating, the racheting pawls may be worn out or broken. The fix is inexpensive and easy, even for a beginner.
Does Whirlpool have a dog agitator?
The ratcheting pawls (called “dogs”) can wear out with age, or break if you overload the machine. When that happens, the washing machine agitator dogs won’t rotate . The parts are cheap (less than $5 at appliance repair stores) and the repair is easy. Whirlpool used two ratchet designs, depending on whether the washer has a plain agitator or one equipped with a fabric softener dispenser. Replacing the agitator dogs in a plain agitator is more complicated and that’s the one we show here.
Does Whirlpool have a fabric softener dispenser?
Whirlpool used two ratchet designs, depending on whether the washer has a plain agitator or one equipped with a fabric softener dispenser. Replacing the agitator dogs in a plain agitator is more complicated and that’s the one we show here.
What to do if washer won't agitate?
If the washer won't agitate, replacing the agitator repair kit may solve the problem . The kit contains the agitator components that are most likely to wear out and/or fail. If any of the parts are worn out, stripped, or damaged, replace the kit.
Why won't my washing machine agitate?
If the washing machine will not agitate correctly the washplate might be damaged and stripped off the drive shaft. The agitator can be removed to check out the washplate connection point.
What happens if a tub rotor is damaged?
If the rotor is damaged, replace it. The stator interacts with the rotor to create a strong electromagnetic field which rotates the tub in either direction. If the windings on the stator are damaged, the washer will not spin or agitate. Check the stator for damaged windings or other defects.
What does a door lock do on a washer?
The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, use a multimeter to test each of the door lock switches for continuity.
Why does a washer coupling fail?
If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission. The motor coupling can also fail due to normal wear. Inspect the motor coupling to determine if it is broken.
Why does my washer not spin?
The rotor interacts with the stator to create a strong electromagnetic field, which rotates the tub in either direction. If the magnets on the rotor are damaged, or any part of the rotor is defective, the washer may not spin or agitate. To determine if the rotor is defective, inspect the rotor for damage.
How to check if a motor control board is defective?
First, check the control board for burned out components. To determine if the motor control board is defective, ensure that the control board is providing power to the motor. If the control board has power, but is not providing power to the motor, replace it. Required Part.
What is the agitator in a washing machine?
The agitator, propelled by the transmission output shaft, is what moves the clothes in the mix of water and detergent to get them clean. The transmission output shaft is splined, which means that grooves in the shaft mate to grooves in the agitator so they fit tightly together. On some models, the agitator’s in one piece ...
What to do if your washer is not agitating?
So if your washer is filling with water but not agitating, it would be logical to make sure the water level switch is operating. You can unplug the washer and check the terminals of the water level switch for continuity, using a wiring schematic for your washer model and your multi-meter.
How to tell if a coupler is damaged?
A symptom of a damaged coupler is a grinding sound during the wash cycle, and the agitator spins freely. Unplug the washer and use some strength to pull the agitator straight up because it’s generally tightly attached. Take off the bolt that holds the coupler onto the shaft of the transmission and pull that coupler off.
How to fix a washing machine that is making a grinding noise?
They click into a corresponding set of cogs to rotate the top of the agitator one way, and then release while the bottom half of the agitator turns in the opposite direction. This action causes the corkscrew shape of the top portion of the agitator to push the clothes down into the bottom of the tub which provides increased turnover of the clothes and better cleaning. The engagement and disengagement action of the cogs wears them smooth eventually, and then the upper half of your agitator won’t move any more. Unplug the washer and take the cover off the fabric softener dispenser . There will be a bolt there holding the top half of the agitator on. Undo the bolt, take off the agitator’s top portion, and look to see if the agitator cogs have worn smooth and need replacement. Check the bearing support, also made of plastic.
Why won't my washer agitate?
If you have a top-load washer that won’t agitate and you’ve been hearing a vibration , there may be a problem with the direct drive motor coupling between the transmission and the motor. This coupling is two drive forks made of plastic, one attached to the shaft of the drive motor, and one attached to the input shaft of the transmission. Then there is a rubber coupling between them that protects the forks by absorbing the torque. But over time, the coupling can wear out and allow those plastic forks to slide and vibrate. The coupling can also get broken when the spin basket is impeded or the transmission seizes. You can enter your model number in the search engine here to find the exact location of this coupling, unplug the washer, and access the direct drive motor coupler behind the cabinet of your washing machine by removing the pump and the motor.
How does a washing machine work?
On a washing machine, the motor creates a rotating motion and the transmission is what transforms that circular motion into the push-and-pull of the agitator. The input shaft of the transmission receives power from the motor via a belt, or sometimes directly. The output shaft is what powers the agitator. Does the input shaft on your machine turn? If it does but the agitator isn’t moving, then the thing between the two of them – the transmission – is the problem. Rebuilding a transmission isn’t always practical here. It is often more practical to replace the complete unit if it is broken. Since the tub seal can be found where the transmission shaft enters the tub, you will probably need to get a new tub seal when you buy a new transmission.
How do washing machines control the speed of the drive motor?
Some washing machines control the speed of the drive motor via a selector switch. If yours does, and you suspect this switch is what’s preventing agitation, unplug the machine and check for continuity with your multi-meter. You can isolate the correct terminals to check by consulting your model’s wiring schematic.
