
Fixing the Broken Line
- Saw off a 4 in (10 cm) section of pipe at the leak. You need to remove a large enough section to fit your slip...
- Place a band clamp on each end of the pipe. A band clamp is a strap of metal that forms a loop that you can tighten.
- Insert a slip coupling into the pipe. A slip coupling is a plastic pipe that is flexible and allows you to...
How do you fix a broken sprinkler line?
A broken sprinkler line can seem like a difficult and expensive repair, but it’s actually pretty simple to do. First, find the leak by looking for escaping water or sprinkler heads with little to no flow. Then, dig up and expose the damaged pipe so you can remove it.
How do you fix a broken pipe on a sewer line?
Clean off the line, or pipe, with a rag so you can see it and its break well. Remove the broken section of pipe as well as 4 to 5 inches of the pipe on each side of the break by cutting through the pipe with a hacksaw. Use a clean rag to dry thoroughly both sides of the remaining pipe inside and out.
What is a broken irrigation line on a lawn?
Lawn irrigation lines are the pipes that direct water from your home's main line to the irrigation system's valves, or from valves to sprinkler heads. If the water pressure is weak from some of your irrigation system's sprinkler heads or large puddles appear on your lawn, then the problem could be due to a broken irrigation line.
What should I do if my irrigation pipe is damaged?
Be careful to keep any dirt, rocks or other debris from getting into the irrigation lines while you're removing and replacing the damaged pipe. Remove enough soil and debris from around the damaged pipe to allow plenty of cleared space to work.

How do you repair PVC irrigation lines?
0:113:543 Ways to Repair PVC Irrigation Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip theMoreSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip the coupling over one section of the pipe. And then over the other tighten. The nuts.
Can you patch a punctured sprinkler line?
2:024:32Howto: fix a puncture in your sprinkler system - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically I just use this this tool here you can use whatever you can use a razor blade you cutMoreBut basically I just use this this tool here you can use whatever you can use a razor blade you cut it cut it right at the the crack.
How do you seal a broken sprinkler pipe?
0:463:30How to Repair a Broken Irrigation Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing you want to do is put primer on the fittings that just takes off any oxidation. Or dirtMoreFirst thing you want to do is put primer on the fittings that just takes off any oxidation. Or dirt that's on the fitting. So you want to glue both the socket and the male end of the pipe.
How do I fix a hole in my irrigation hose?
0:001:10How To Repair Holes in Drip Irrigation Tubing - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a pair of pliers to grip the smaller of the two sides. Position over the hole to be plugged andMoreUse a pair of pliers to grip the smaller of the two sides. Position over the hole to be plugged and push in a popping. Sound should be heard indicating the goof plug is fully seated in the tubing.
How do you fix a broken sprinkler pipe under concrete?
Swab one end of the pipe with PVC glue and then press a PVC coupler onto the end of the pipe. Swab the end of the exposed section of pipe that you cut from with PVC glue and press the other end of the coupler onto the pipe. This will seal the connection on one end of the concrete.
How do you fix a black irrigation tubing?
1:154:04How To Repair A Broken Leaking Black Plastic ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's several different types of hose clamps I use the simple ones with a little screw on top.MoreThere's several different types of hose clamps I use the simple ones with a little screw on top. Middle worm drive that kind of tightens them up.
How to repair a broken irrigation line?
How to Repair a Line Break in an Irrigation System. If you suspect that you have a line break in your irrigation system, you’ll need to locate the exact pipe that is broken in order to repair it. First, determine whether the line break is in a main “constant pressure” line or a lateral “zone” line. The main line is the pipe ...
What happens if you break a lateral line in your irrigation system?
If you suspect that you have a line break in your irrigation system, you’ll need to locate the exact pipe that is broken in order to repair it. If you have a break in a lateral line, the leaking water will surface and pool only when the system is turned on.
How to fix a PVC pipe that has pooled water?
Place a pipe clamp on either end of the fitting and crimp the connections closed. Remove any pooled water from around the PVC pipe. Insert one end of the telescoping repair coupling to one cut end of the PVC pipe. Extend the repair coupling to the other cut end of the PVC pipe and insert it. Allow the glue to dry and set before testing the system.
How to get rid of water pooling in the ground?
Dig a hole into the ground using a spade or shovel to remove sod and soil from the area where the water is pooling. Determine what kind of pipe is broken, such as a PVC pipe or a smaller, flexible polyethylene pipe. Dig and remove the soil around the pipe. If your line break is in a poly pipe that is usually used for lateral lines, ...
Why is my lawn pooling?
Possible causes include frost and frozen water damage, cracks or holes caused by lawn aerators or other equipment, damage from deep-growing roots, bad installation or defective pipes and fittings, or punctures from digging animals. Dig a hole into the ground using a spade or shovel to remove sod and soil from the area where the water is pooling. ...
What is the main line?
The main line is the pipe that delivers pressurized water from the main water source to the lateral zone lines. If you have a break in the main line, you’ll see water leaking and pooling in large quantities, even when the system is turned off. If you have a break in a lateral line, the leaking water will surface and pool only when ...
How to remove a broken pipe?
Remove the broken section of pipe as well as 4 to 5 inches of the pipe on each side of the break by cutting through the pipe with a hacksaw. Use a clean rag to dry thoroughly both sides of the remaining pipe inside and out.
How to find a leak in a sprinkler system?
1. Locate the source of the leak by turning on the water to the irrigation system and waiting for a pudd le to begin to form on the ground. The leak probably is directly below the beginning of the puddle. Alternatively, turn on water to the irrigation system, and look for weak water flow from sprinkler heads. Water will dribble instead of spray ...
Why is my lawn watering so weak?
Lawn irrigation lines are the pipes that direct water from your home's main line to the irrigation system's valves, or from valves to sprinkler heads. If the water pressure is weak from some of your irrigation system's sprinkler heads or large puddles appear on your lawn, then the problem could be due to a broken irrigation line.
Can you dig sod back in place?
Digging to the line to repair it is necessary, but dig carefully so you don’t harm the line or ruin the look of the lawn. Meticulously cut sod can be put back in place with little impact on the lawn's health or aesthetic appeal.
How to stop water from pouring out of pipe?
Clean the pipe. Some water will come pouring out at first, you could try to catch it, but it is easier to bail it out. Once the water stops coming out, clean both ends with a rag. ...
How long should a PVC pipe be?
Or you can buy a PVC fitting from most home improvement stores that has one pipe sliding inside an outer barrel with an O-ring inside. It will extend almost 3" in length. You may see in stores 1/2" to 2 1/2" in diameter sizes.
