Repairing A Hand Crank Camper Jack The first step is to remove the top cover to get to the gears and the shaft that connects the handle. Removing gear cover In this case, you remove a metal band that holds the cover on. For jacks with a side handle, you normally just pop off a plastic plug in the top of the tube.
How much does it cost to replace a camper Jack?
If the Happijac technicians determine that the camper jack is repairable, the charge is $59.95 plus shipping to recondition the jacks including replacing all worn parts and re-lubricate the jack.
How do I Keep my camper jacks from going bad?
Just that motion helps to keep the jacks running well. Don added that, if you keep your camper on your truck, make sure that you run the jacks up and down twice a year to keep them lubricated. You can also clean the outside of your camper jacks with soapy water and wax them to keep them looking like new.
How do you lower a truck camper with an electric Jack?
Don answered that you can always hand crank your electric jacks to get them to retract and lower (or raise) your truck camper. To do this, remove the white cap on the camper jack leg covering the crank socket, and use the hand crank. Push the lever down. This disengages the motor by lifting the coupler off from the screw.
What is a HappiJac camper Jack?
Truck Camper Magazine asks Don Payne, Happijac’s Product Manager, about the proper use and maintenance of Happijac camper jacks. Camper jacks are an often overlooked feature of a truck camper, but they are the key feature that make modern truck camping possible. Think about it, truck campers that you couldn’t load or unload wouldn’t be much fun.
How do you repair a hydraulic jack on a camper?
11:0914:38Hijacker Camper Jacks | Top End Rebuild and Priming - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then put your feet on the bottom. And then pull up all the way. And then you open up your valveMoreAnd then put your feet on the bottom. And then pull up all the way. And then you open up your valve a few turns. Like that so it's open so it's open and then you let it back down.
How do you fix a jack mount on a camper?
0:297:19Fixing a broken camper jack mount (HOW TO) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's an angle bracket over here that'll go on the corner of the camper. And this is what the jackMoreThere's an angle bracket over here that'll go on the corner of the camper. And this is what the jack gets bolted to. So what I'm doing is just reinforcing this corner.
How do you add hydraulic fluid to Camper jack?
Turn the release valve on the Hijacker camper jack clockwise to close it. ... Stand on the leg pad and pull the jack up to extend it fully.Turn the reservoir bolt counterclockwise with a wrench to remove it. ... Fill the reservoir with hydraulic oil. ... Reinsert the bolt and O-ring into the reservoir hole.More items...
How do you disassemble a trailer jack?
0:404:12Repairing Your Trailer Jack Drive Screw - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull back the retaining spring push the pin down rotate the jack handle 180 degrees. And pull outMorePull back the retaining spring push the pin down rotate the jack handle 180 degrees. And pull out the pin remove the cross shaft remove the spring top gear and bushing then lift out the bottom gear.
How do you reinforce a camper Jack?
1:313:03Truck Camper Jack Hack How To Fix loose Jacks. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlright what I'm using today is this Loctite PL proline marine fast cure adhesive sealant good forMoreAlright what I'm using today is this Loctite PL proline marine fast cure adhesive sealant good for above or below the waterline.
How do you install an RV Jack?
0:124:04Reviewing how to use Mechanical Camper Jacks l Four Wheel CampersYouTubeStart of suggested clipEnd of suggested clipWe usually recommend loading the camper securing your tie-downs turnbuckles plugging the camper inMoreWe usually recommend loading the camper securing your tie-downs turnbuckles plugging the camper in and leaving your Jack's at home. Having these four Jack's hanging off the side of the camper.
What fluid goes in a camper jack?
The use of HWH Specialty Hydraulic Oil is recommended but Dexron or multipurpose transmission fluids can be used if necessary.
How do you lubricate RV leveling jacks?
0:343:45Cleaning and lubricating RV JACKS and SLIDES - YouTubeYouTubeStart of suggested clipEnd of suggested clipOil you're going to come back with your dry lube. And you're just going to simply spray your dryMoreOil you're going to come back with your dry lube. And you're just going to simply spray your dry lube. So that's how you take care of these underneath your slide out if you have a through frame.
Can I use brake fluid in a hydraulic jack?
It is highly discouraged to use brake fluid in a hydraulic fluid in a floor jack. The brake fluid contains a lot of additives that are not required in a jack. Using the brake fluid will severely damage the seals of the hydraulic jack.
Can a trailer jack be rebuilt?
Rather than going through the expense of buying a new jack and having it welded on or reattached to your trailer, you can simply rebuild the one you've got and save quite a bit of money.
How do you replace the spring on a trailer jack?
0:241:22Replacing a Swivel Pin Kit on Tongue Jacks - Step-By-Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you can insert a new cotter pin into the hole in the handle bend. The end of the pin with yourMoreSo you can insert a new cotter pin into the hole in the handle bend. The end of the pin with your pliers. So it stays in place. Then you'll be able to once more swivel your jack on and off the ground.
Why is my trailer jack not working?
Expert Reply: For your electric jack, there are only three possible explanations for your jack not working with a charged battery. Either power is not getting to your motor, your motor is bad, or your ground connection isn't working properly.
How do you fix an RV corner?
2:295:42How To Reseal RV Corner Molding - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe sealing tape of the corner seal consists of a thick pressure-sensitive elastomeric seal theMoreThe sealing tape of the corner seal consists of a thick pressure-sensitive elastomeric seal the fleece side provides better caulk cure adhesion than the typical smooth surface of RV exterior.
How do you lube a Rieco Titan camper Jack?
To oil the jacks, squirt enough oil into the gearbox to keep the jacks lubricated. Tripod jacks are used because some campers need to be supported by the bottom of the camper instead of the sides. Rieco-Titan offers two types of tripod jacks; the Heavy Duty Tripod Jack (left) and the Standard Tripod Jack (right).
What is a camper jack?
Camper jacks are an often overlooked feature of a truck camper, but they are the key feature that make modern truck camping possible . Think about it, truck campers that you couldn’t load or unload wouldn’t be much fun. If life were a drive through, we would order our truck campers to go.
How much steel is used on Happijac camper jacks?
To further strengthen their camper jacks, Happijac has added a strip of one-quarter inch steel at the bolt strip, where the outer tube connects to the camper. Don said that the bolt strip is a full eighteen inches from top to bottom to add even more of a strength and safety margin.
How much does a Happijac 4150 jack weigh?
The rating on the Happijac 4150 acme camper jack is 1,500 pounds per jack under the ANSI national standards. With the acme jacks, it takes six revolutions to move an inch vertically. Don explained that you have 34” of extension on the Happijac 4150 before you get a warning and the jack is overextended.
Why does the clutch on a Happijac jack ratchet?
He explained that the clutch inside the motor of a Happijac camper jack is designed to ratchet when it’s overloaded. If this occurs, Don suggested rebalancing the camper with the other three jacks to relieve some of the weight off the ratcheting jack.
What are the parts of an electric jack?
The electric jacks are comprised of two basic components, the motor head assembly and the jack leg. These two components are separated with two screws on either side of the jack top, below the motor head assembly. When removing the motor head assembly, there should be a coupler, a spring, and a washer.
Is Happijac camper jack conservative?
As Don explained it, Happijac is very conservative with it’s camper jack ratings and over designs their jacks for safety. Of course this is not an invitation to overload your jacks, but it’s certainly reassuring to hear that Happijac is serious about our safety.
Can Happijac camper jacks be taken apart?
All Happijac camper jacks utilize a double breaking system to safely control the decent of a truck camper. Don warned that Happijac camper jacks are never to be taken apart in the field as they are very complex and an incorrectly re-assembled jack could cause serious safety issues.
