
HOW TO FIX A SEAT BELT RETRACTOR? 5 EASY STEPS.
- 1. TAKE OFF THE TRIM PANEL. Before you start fixing, a safety precaution: Take off the minus battery terminal on the car. This is to avoid accidental ...
- 2. CHECK THAT THE SEAT BELT RETRACTOR IS THE ACTUAL PROBLEM.
- 3. RETRACT THE SEAT BELT AS MUCH AS POSSIBLE.
- 4. CLEAN THE AREA AROUND THE SEAT BELT RETRACTOR.
- 5. APPLY WD-40 OR A SILICONE BASED SPRAY TO THE SEAT BELT RETRACTOR.
How do you fix a retractable seat belt?
Possible Problems
- Defective seat belt retractor. The seat belt retractor may be broken and needs to be replaced. ...
- Twisted seat bel. You may have to remove the plastic trim to check and make sure that the seat belt is not twisted. ...
- Previous accident. ...
- Seat belt age. ...
- Bad Retractor Spring. ...
How to fix a retractable seat belt?
Here’s the procedure:
- Take the proper wrench and take the belt loop of. A screw is often hidden under a small plastic covering on the loop itself.
- Take the trim tools and take off the trim. Be careful and take your time as this is a tricky job. ...
- After the trim is off, you’ll see the retracting mechanism. ...
How to fix locked seat belt after accident?
Your seat belt pretensioner may need repair if:
- The seat belt is too tight or too loose.
- The seat belt won’t retract after releasing.
- The seat belt doesn’t stay taut.
- The seat belt won’t lock or unlock.
- The seat belt stays locked.
How do you open a seat belt receiver to repair?
Method 2 Method 2 of 2: Removing and Reinstalling the Front Seat Download Article
- Slide the seat as far forward as it can go. ...
- Take out the seat belt anchorage point with a socket wrench. Seat belt anchorages are often hidden behind a piece of trim.
- Remove the bolts at the back of the sliding rails and tip the seat forward. ...
- Reconnect the electrical wires to begin reinstalling the seat. ...

How much does it cost to fix a seat belt retractor?
The replacement cost of a seat belt pretensioner is around $150 to $200. The cost of the parts is about $50 to $100 while the cost of the labor is about $100 to $125. You may be able to reduce the labor if you can find a cheap enough mechanic in your area or simply enlist the help of a buddy that likes to work on cars.
How do you fix a seatbelt retractor spring?
3:239:37Rewinding a Seat Belt Return Spring and What NOT To Do - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo with a Philips screwdriver you can take out these two screws on either side of this blue coverMoreSo with a Philips screwdriver you can take out these two screws on either side of this blue cover make sure you push down and that you're sure you're not going to lose it.
Can I replace a seat belt retractor?
If the seat belt in your car needs a new retractor, you can follow these steps to replace it yourself at home: Locate the retractor on your seat belt. Remove the mounting screws on the retractor cover, followed by the cover itself. Remove the retaining bolt mounting the retractor.
What causes a seatbelt not to retract?
If the seat belt in your car isn't retracting, there are two probable causes: the belt is twisted, or the retractor is malfunctioning. You'll be able to fix the belt yourself, but you'll need to replace the retractor if it's malfunctioning.
How does a seat belt retractor work?
2:007:41Seatbelt | How does it work? - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis movement will move the hinge and trigger a locking mechanism. This locking will prevent anyMoreThis movement will move the hinge and trigger a locking mechanism. This locking will prevent any further release of the webbing from the retractor.
How much does it cost to replace a seatbelt in a car?
In general, replacing your seat belt will cost between $20 to $85 for the belt itself and an additional $100 to $125 to have a mechanic install it. Like most car parts, the exact price of your seat belt is determined by the make and model of your vehicle.
Why is my seat belt locked up?
To begin with, a seat belt can be stuck due to two reasons: a) the problem may lie in the retractor being locked, and b) dirt or grime may have accumulated on the seat belt, causing it to retract slower than usual and not all the way. For the latter, a simple cleaning will hopefully fix the problem.
How do you install seat belts?
1:3815:08How to Install a 3 Point Retractable Seat Belt | Kevin Tetz with LMC TruckYouTubeStart of suggested clipEnd of suggested clipTools that you'll need for this project are pretty basic you're gonna need a wrench set I prefer aMoreTools that you'll need for this project are pretty basic you're gonna need a wrench set I prefer a combination wrench set to give you options of course they're SAE sizes.
How do you take the seatbelt out of a Miata?
0:088:12Seatbelt mechanism removal for 1990-1997 Mazda MX-5 Miata.YouTubeStart of suggested clipEnd of suggested clipAnd what you want to do is just pull the middle piece out like that. And then you can get it outMoreAnd what you want to do is just pull the middle piece out like that. And then you can get it out without breaking.
Step One: Disconnect the Trim Panel
Before you begin, take the negative battery terminal off the battery to keep the explosive charge on the seat belt retractor from accidentally igniting! While working, you may unintentionally disconnect or damage the electrical connector, so use caution.
Step Two: Check to See If the Retractor Is Broken
Remove the panel to reveal the seat belt retractor. It can be found in the B pillar.
Step Three: Retract the Seat Belt
Tighten the seat belt all the way. With the metal spool to cloth endpoint, it may now be able to retract more readily. A gentle pinch around the seat belt loop will suffice in this circumstance.
Step Four: Remove Dust and Debris
The retractor could be covered in dust and filth that looks like wool. It should be cleaned up with a vacuum or compressed air. Cleaning the seat belt retractor usually improves its function. In many cases, grime obstructs the mechanism's operation. Therefore, cleaning it is useful.
Step Five: Wrap a Silicone Spray or WD-40 into the Seat Belt Retractor
After cleaning, lubricate the retractor with a WD-40 spray or a silicone-based spray. Spray the retractor's plastic part between the rotating metal spool and the retractor's metal spool with the retractor's metal spool. Instead of flooding it, use brief bursts. If this was the case, the matter should be resolved as soon as possible.
Conclusion
While repairing a seat belt retractor is doable, it’s not that easy, and you may feel frustrated if you can’t fix it yourself. The best course of action is still to bring your seat belts to the experts. They know exactly what to do, saving you the time and effort you could have spent elsewhere.
What to do before fixing seat belt retractor?
Before you start fixing, a safety precaution: Take off the minus battery terminal on the car. This is to avoid accidental activating of the explosive charge on the seat belt retractor! You might, while working, accidentally disconnect or damage the electrical connector so better safe than sorry.
Where is the seat belt retractor located?
Once you take off the panel, you’ll see the seat belt retractor. It’s in the lower part of the B pillar. This is a good time to check and be sure that the retractor is the actual problem. After all, if you want to learn how to fix a seat belt retractor, you have to know that it’s causing the problem not anything else.
Can a screwdriver damage a seat belt?
Using a screwdriver or any kind of metal tool will damage the trim panel for sure or leave nasty scratches and bents. Besides this, you might need a ratchet and matching sockets for additional dismantling (like taking off parts of the seat belt assembly, various holders, or else). Prior knowledge.
What is a seat belt retractor?
A seat belt retractor consists of a spring, some gears, a sensor, a pyrotechnic explosive device. It is a safety mechanism designed to lock up during a vehicle collision or accident. If you want to replace it, here’s what you need to do:
Why won't my seat belt pull out?
The chances are that they can’t seem to pull out because of two reasons: dirt or grime and stuck belts. When these happen, they won’t be able to ensure your safety and of your passengers’.
