Move the ignition switch on the Craftsman into the “Off” position. Unscrew the starter assembly cover and remove it from the trimmer using the screwdriver. Flip the starter cover over to replace the pull cord. Cut the old cord off the pulley and the starter handle. Throw the old cord away.
Full Answer
How do you replace a pull cord on a craftsman weed trimmer?
Cut the old cord off the pulley and the starter handle. Throw the old cord away. Push the new cord through the middle of the pulley, the hole in the starter cover and the center of the starter handle. The pull cord on a Craftsman weed trimmer operates the starter mechanism so the operator can get the combustion process started.
How do you replace the pull cord on a husky Trimmer?
Unscrew the starter assembly cover and remove it from the trimmer using the screwdriver. Flip the starter cover over to replace the pull cord. Cut the old cord off the pulley and the starter handle. Throw the old cord away. Push the new cord through the middle of the pulley, the hole in the starter cover and the center of the starter handle.
How do you change the starter cord on a craftsman mower?
Move the ignition switch on the Craftsman into the “Off” position. Unscrew the starter assembly cover and remove it from the trimmer using the screwdriver. Flip the starter cover over to replace the pull cord. Cut the old cord off the pulley and the starter handle. Throw the old cord away.
How to fix a craftsman trimmer that won’t start?
This cord can get pulled off from excessive tugging when the engine won’t start or it may get ripped or frayed, forcing the operator to replace the cord before he can start trimming again. Move the ignition switch on the Craftsman into the “Off” position. Unscrew the starter assembly cover and remove it from the trimmer using the screwdriver.
How do you replace the pull string on a craftsman weed wacker?
1:015:32fix broken weed wacker pull cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipI used a flat head screwdriver. And it worked just fine.MoreI used a flat head screwdriver. And it worked just fine.
How do you fix the pull cord on a weed wacker?
0:493:27Quick easy Weedeater pull string fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen pull out the starter pulley and remove what's left of the old string. Then put your new stringMoreThen pull out the starter pulley and remove what's left of the old string. Then put your new string into the pulley and through the hole the old one was at then make a knot at the end of the new rope.
How do you replace the pull cord on a craftsman?
4:1715:37Replacing the Starter Rope on the Craftsman Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo now grab the needle nose pliers. Right here on the end of the rope just to try. And get the ropeMoreSo now grab the needle nose pliers. Right here on the end of the rope just to try. And get the rope out. And as you can tell right here got another piece right here.
How do you take apart a Craftsman weed eater?
0:402:56Removing Craftsman (Model:CMXGTAMD25SC) Trimmer ...YouTubeStart of suggested clipEnd of suggested clipTurn the the head and you'll see that slot right there. You might even use a allen wrench if youMoreTurn the the head and you'll see that slot right there. You might even use a allen wrench if you have when I didn't have one available so I just played it at all that head screwdriver.
How do you fix a pull start that won't retract?
0:352:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
What does it mean when the weed eater string won't pull?
You usually need access to the recoil mechanism to fix these problems, although if the cord is simply stuck, you might be able to free it by giving it an extra-hard tug. If the cord won't retract, it may also be because something is tangled inside the recoil housing, but more often, the problem is a broken spring.
How do you replace a pull string?
2:033:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How do you fix a pull cord spring?
0:096:40How to fix a pull starter recoil spring and replace a stuck or limp pull cordYouTubeStart of suggested clipEnd of suggested clipJust kind of have to work it with your pair of pliers the most important thing is. This is whereMoreJust kind of have to work it with your pair of pliers the most important thing is. This is where it's gonna go once it's in there it's gonna go like this.
How do you fix a Briggs and Stratton pull cord?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken.MoreNow once the three bolts are off just simply remove the cover. Now this recoiled the rope is broken. So all I have to do is to pull the rope out of the eyelet over here.
How do you string a Craftsman 25cc weed eater?
2:254:34How to Restring a Craftsman Weedwacker - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo push the little button turn it back down. And make sure your handle is nice and tight. And you'reMoreSo push the little button turn it back down. And make sure your handle is nice and tight. And you're ready to go again. So that's it this is how to restring the craftsman ws 2200.
How do you take the head off a Craftsman electric weed eater?
How Do I Remove the Head From a Craftsman Line Trimmer?Deactivate your trimmer and remove it from any power source. ... Turn the trimmer upside down so that the head is facing up toward you. ... Depress each tab at the same time, releasing the head from the rest of the trimmer.
What makes a weed eater hard to pull?
Most of the time, the cause is an issue within the pull mechanism itself. The three most common issues associated with a string trimmer pull mechanism that makes it harder to pull are a broken cord, a stuck cord, or a recoil spring that is damaged.
How do you replace the starter rope on a Troy Bilt weed eater?
6:0110:49Replacing the Recoil Spring (Troy-Bilt Part # 753-04286) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the eyelid on the starter housing I'll insert the rope through both the eyelet and the hole inMoreWith the eyelid on the starter housing I'll insert the rope through both the eyelet and the hole in the pulley.
How to tension a recoil spring?
Hold the starter cover and wind the loop and pulley four to six revolutions to tension the recoil spring. Press and hold the pulley with your thumb. Let go of the loop and unwind the cord. Lift your thumb off the pulley slowly to let the cord rewind onto the pulley.
How to unwound a pulley?
Tie a knot above the starter handle and at the base of the pulley. Wind the cord around the pulley until 10 inches remain unwound. Form a loop into the unwound portion.
How to replace a starter cord on a pulley?
Cut the old cord off the pulley and the starter handle. Throw the old cord away. Push the new cord through the middle of the pulley, the hole in the starter cover and the center of the starter handle.
How to change pull cord on Craftsman?
Move the ignition switch on the Craftsman into the “Off” position. Unscrew the starter assembly cover and remove it from the trimmer using the screwdriver. Flip the starter cover over to replace the pull cord.
How to remove weed wacker pulley?
Place your weed wacker on a flat surface and allow it time to cool completely. Put gloves on to protect your hands. The number of screws differ from model to model. Release the tension on the pull cord and allow it to wind into the pulley. Remove the center screw in the assembly with a screwdriver. Lift the old recoil pulley out of the assembly. ...
What is a pull cord on a Craftsman weed trimmer?
The pull cord on a Craftsman weed trimmer operates the starter mechanism so the operator can get the combustion process started. The pull cord allows the operator to turn the flywheel by hand until it spins fast enough and the engine takes over the process. This cord can get pulled off from excessive tugging when the engine won’t start ...
Where to tie a knot on a pulley?
Tie a knot above the starter handle and at the base of the pulley.
What Can Go Wrong With a Pull Cord?
The three most common problems that can arise with a pull cord are that:
How to remove pulley from watch?
The pulley is usually held to the shaft by a retaining ring that you should be able to pull off with your fingers or with pliers. You'll find a spring under this ring. Be sure to save it. Once the ring and spring are gone, you can remove the pulley. Behind it, you'll find a recoil spring, much like the one you see in mechanical watches. If you have to replace this spring, which you probably do, purchase a kit that includes both the spring and its housing. You don't want to get stuck with the job of forcing a new spring into the old housing.
How to wind a cord on a motor?
After that's done, allow the pulley to slowly recoil, which will automatically wind the cord until the handle is flush against the motor housing.
How to unscrew clutch plate?
Wedge a flat-head screwdriver on the end of one of the clutch plates and tap it with a hammer to turn the plate counterclockwise. The shock should free it enough to allow you to unscrew it by hand. Repeat with the other clutch plate.
Why won't my cord retract?
If the cord won't retract, it may also be because something is tangled inside the recoil housing, but more often, the problem is a broken spring. Either way, you need to get into the recoil mechanism to fix it.
Where is the starter recoil mechanism on a string trimmer?
On some string trimmers, the starter recoil mechanism is mounted on the engine housing, often near the muffler. If yours is one of these, all you have to do to uncover the starter is remove a few screws and a plastic cover. On some models, however, a fair amount of extra disassembly is required because the recoil mechanism is inside the engine housing directly behind the clutch. To get to it, you have to do the following, using your owner's manual as a guide for model-specific procedures:
Where is the starter recoil mechanism?
On some trimmers, the starter recoil mechanism is mounted on the engine housing, often near the muffler. If yours is one of these, all you have to do to uncover the starter is remove a few screws and a plastic cover. On some models, however, a fair amount of extra disassembly is required because the recoil mechanism is inside ...
How to get rid of a stuck pull cord?
A few preventative measures can help reduce the occurrence of a stuck pull cord. Unscrew the screw on top of the housing to gain access to the cord and pulley disc for further inspection. Return the disc and cord to their proper locations, reversing the order of removal.
How to fix a Craftsman mower that has broken?
Clamp the pulley with your vise grips or a clamp to hold it in position. If the lawnmower pull cord for your Craftsman mower has broken, you'll be stuck with dead piece of lawn gear. Loosen and remove the bolts securing the engine cover to the mower deck, using a socket set. Thread the end of the cord through the hole in the pulley.
What happens if the pull cord on a Craftsman lawn mower breaks?
If the lawnmower pull cord for your Craftsman mower has broken, you'll be stuck with dead piece of lawn gear. But fortunately it isn't difficult to replace the cord and get your machine running again.
Where is Nichole Liandi?
Based in Virginia, Nichole Liandi has been a freelance writer since 2005. Her articles have appeared on various print and online publications. Liandi has traveled extensively in Europe and East Asia and incorporates her experiences into her articles. She holds a Bachelor of Arts in history from West Virginia University.
How to release tension on pulley?
Release the tension by unwinding 10 inches of cord from the pulley, catching it in the notch in the rim and holding the rope while the pulley slowly unwinds .
How to tie a pulley to a spring?
Hook the 10-inch length of rope in the notch on the rim of the pulley and use the rope to wind the pulley clockwise through two complete turns to put tension on the spring. Align the notch with the hole in the housing; and, holding the pulley steady with one hand, pull the rope tight from outside the housing. Let the pulley unwind and wrap the rope around itself.
How to connect a fan to a pulley?
Feed one end of the cord through the hole in the fan housing and through the top hole on the inside of the pulley. Guide the cord through this hole by inserting a screwdriver through the hole underneath it and pushing it. Wrap the cord counterclockwise around the pulley ratchet and then secure the end by tucking it under the wrapped cord. Pull on the cord tightly.
Can a Craftsman leaf blower be used as a vacuum?
The Craftsman brand includes many models of leaf blowers, some of which can be converted for use as a lawn vacuum. You'll have many opportunities to use this handy tool, especially in the fall, and you'll eventually have to replace the starting cord, which will fray and break. Unlike the one on many gas-powered tools, the recoil starter on a Craftsman leaf blower doesn't come out as a unit. Instead, you have to pull the pulley off the spring. When you do this, it's essential to leave the spring undisturbed in the housing. It is difficult to replace.