How To Fix a Delta Monitor Shower Faucet
- Prepare Your Tools. Always order the exact replacement parts to avoid problems.
- Shut the Water Supply. Before you do any repair, always stop the flow of water into your faucet right at the main source.
- Remove Set Screw Lever Handle. ...
- Pull Down Orderly Covering, Bonnet and O-Ring. ...
- Remove the Cartridge. ...
- Replace O-Rings. ...
- Reassemble the Faucet. ...
Full Answer
How to repair old school Delta single handle shower faucet?
- With the handle removed, remove the trim sleeve and then the spacer. ...
- Now you’ll want to remove the bonnet nut with s strap wrench.
- Grab onto the valve cartridge and wiggle it back and forth while also pulling on it. ...
- Take your new cartridge and insert it. ...
- You’ll now want to line up the keys on the side with the slots found in the valve.
How to fix a leaky Delta Faucet?
- Best fish tank: Stylish abodes for your aquatic amigos
- How to clean a fish tank
- Best small fish tank: Petite pads for your tiny tribe
How to replace washer in Delta shower?
Things You'll Need
- Dull knife or flathead screwdriver
- Adjustable pliers
- Phillips head screwdriver
- O-ring
- Stem washer
- Heatproof grease
How do you replace a Delta shower cartridge?
Things You'll Need
- Phillips screwdriver
- Flat-tip screwdriver
- Slip-joint pliers
- Replacement cartridge
How do I fix a leaky Delta Monitor shower faucet?
0:117:45Repair a Leaking Delta 1700 Shower Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipSeries faucet in our shower. And it's developed a little leak it's got a drip probably every 60MoreSeries faucet in our shower. And it's developed a little leak it's got a drip probably every 60 seconds to two minutes.
How do I remove a Delta Monitor shower cartridge?
2:516:30How to Replace a Delta Faucet Shower Cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a strap wrench or a pair of channellock pliers to loosen the bonnet nut by turning itMoreUse a strap wrench or a pair of channellock pliers to loosen the bonnet nut by turning it counterclockwise then remove the bonnet nut by hand.
How do you rebuild a Delta shower faucet?
0:5111:13How to Repair a Delta Tub / Shower Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll have to replace the kit this is what you'll need before you start the job the cam the bonnetMoreYou'll have to replace the kit this is what you'll need before you start the job the cam the bonnet gasket a ball.
How do you remove a stuck Delta Monitor shower handle?
0:563:16Delta Stuck shower handle removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt did not budge or come out at all the only way to get this out is to cut it. And for that you justMoreIt did not budge or come out at all the only way to get this out is to cut it. And for that you just use one of the saw. I had to sneak. My saw in between the blade.
How do I identify my Delta Monitor shower faucet?
The model number is on all packaging, some faucets, and all installation instructions provided with your faucet. On the packaging, look near the UPC code or the top of the box. On the faucet, a model identification tag has been attached to most models manufactured since 2012.
How do I know if my shower cartridge is bad?
There are a few ways to tell if your shower cartridge has gone bad:Dripping or running water when you turn your shower off (most common)Difficulty turning the shower handle, which worsens over time.Shower handle gets stuck or “slips” and doesn't turn on the water.
How do you fix a Delta 2 handle shower faucet?
0:226:52How to fix a leaking, dripping Delta bathtub faucet - $2 fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust take the covers off of these handles. So just get a little knife here. And pop those off nextMoreJust take the covers off of these handles. So just get a little knife here. And pop those off next you can see those screws in there so we've got to take those out so we can take the handles. Off.
How do you fix a dripping Delta faucet?
0:002:11How to fix a leaky dripping Delta faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's usually a screw it'll either screw off or there's a screw hole on the side as is the case onMoreThere's usually a screw it'll either screw off or there's a screw hole on the side as is the case on this one. So once you remove the handle you'll reveal the valve.
How do you take apart a Delta shower head?
0:002:11How To Change A Showerhead by Delta - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust remove the old shower head by turning it counterclockwise. If you can't do it by hand use anMoreJust remove the old shower head by turning it counterclockwise. If you can't do it by hand use an adjustable wrench. Make sure the shower arm doesn't turn inside the wall.
How do you remove a Delta dual function shower valve?
0:165:02How to replace Delta shower cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo on off that has a set screw holding that on there tight. So get an allen wrench loosen that upMoreSo on off that has a set screw holding that on there tight. So get an allen wrench loosen that up and then that part of the handle. Come off.
How do I remove my shower cartridge?
0:0614:48Removing a Stuck Moen Cartridge Without Proper Cartridge PullerYouTubeStart of suggested clipEnd of suggested clipOkay so what we have here is got a call about a dripping shower a shower that won't stop dripping soMoreOkay so what we have here is got a call about a dripping shower a shower that won't stop dripping so it's obviously leaking past the cartridge. So this is a or unit condo complex. And we shut the
How do you change a Delta faucet cartridge?
1:323:15How To Fix A Leaky Delta Two Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a wrench or channel lock pliers to loosen the bonnet nut make sure to note where the quarterMoreUse a wrench or channel lock pliers to loosen the bonnet nut make sure to note where the quarter term stop is set on top of the cartridge. And use a pair of pliers to grab the top of the cartridge.
Step 1: Gather Material Needed
To easily execute this process the following tools are necessary: • Allen Wrenches • Tongue and Groove Pliers • Needle Nose Pliers • Faucet Grease • New Cartridge
Step 2: Turn Off the Water and Drain the System
Caution: Treat old valves with care. 1. Locate the main water shut off for the house or apartment. It will most likely be located in the basement of a house or duplex. There will be one of two types of valves ,a ball valve (see picture 1) or another style of valve shown in picture 2. 2.
Step 3: Remove Trim From the Valve
1. Locate the set screw on the handle. This will be in a recess somewhere on the handle. To disassemble the style in picture 1, the lever will need to be removed to access the screw. 2. Once the lever is removed the screw can be found (see picture 2). Try to evaluate what size allen wrench is going to be needed. Insert that wrench into the hole.
Step 4: Unscrew the Bonnet
Grip the bonnet with your hand and twist in a counter-clockwise direction, continue until the bonnet is completely removed. Tip: To remove the bonnet of an older valve the channel locks may need to be used as shown in the picture. (Caution: Be careful not to apply excessive force when using the wrench, this will deform the bonnet when using the tongue and grove pliers.).
Step 5: Remove the Old Cartridge
âGrip the old cartridge and pull straight back towards you, while applying steady pressure slightly wiggle the cartridge up and down. (Shown in picture 1) Tip: If the cartridge will not come out, the cartridge can be removed with tongue and grove pliers (shown in picture 2), or the needle nose pliers may also be used.
Step 6: Prepare and Install New Cartridge
1. âPut a small dab of faucet grease on your finger and apply the grease to the o-rings of the new cartridge. This will help the cartridge to be installed and seat in the valve body (See picture 1). 2. Locate the H that signifies the hot side of the cartridge.
Step 7: Replace the Bonnet Turn the Water Back on and Check for Leaks
1. Once the cartridge is installed, replace the bonnet. Tighten by hand only, even if it was necessary to loosen the bonnet with pliers, still tighten by hand (see picture 1). 2. Slowly open the main shut off valve about half way (see picture 2). Leave the faucet used to relieve the pressure open while the system is filling.