- Shut off the electricity and water. Unplug the power cord from the wall outlet. Turn off the water supply valves for the washer. ...
- Lift the top panel. Tape the lid shut so it doesn’t flop open and damage the control console or hit your arms as you work.
- Release the lid switch/lock assembly from the top panel. Using a 1/4-inch nut driver, remove the 2 mounting screws that secure the lid switch/lock assembly to the top panel.
- Open the control console. Carefully lower the top panel and rest it on the top of the washer. ...
- Remove the lid switch/lock assembly. Locate the wire harness connection for the lid switch/lock assembly on the back of the control board (The lid switch/lock harness has yellow, blue, ...
- Install the new lid switch/lock assembly. Snap the console back into the mounting clips. Move the washer near the back wall. ...
- Reinstall the console. Position the console on top of the top panel and snap the mounting clips into place to secure the console on the top panel.
- Reinstall the back panel screws. Insert the screws back into the top of the hinges on the back of the control console. Tighten those screws firmly.
- Restore the water and power. Turn on the water supply valves. Plug the washer into the electrical outlet. Return the washer to its original location.
How do you change lid switch on Whirlpool washer?
Method 3 Method 3 of 3: Cutting the Wires for the Lid Lock Switch
- Remove the lid lock switch assembly. Use a 1⁄4 inch (0.64 cm) nut driver to loosen the two mounting screws holding the box in place on the bottom of ...
- Pry the cover off of the assembly. These sorts of covers are almost always secured using retention clips.
- Examine your washer’s tech sheet to determine which wires to cut. ...
How to bypass Whirlpool lid switch?
So this is how to know if a damaged lid lock switch is the one causing your washer problems:
- Disconnect the washer from the power source.
- Open the top panel to reveal the lid lock.
- Clean the lid lock switch with a cotton swab and white vinegar. ...
- Switch on the washer and test if the problem is still there. ...
- Use a multitester to see if there is a current flowing through the lid lock switch. ...
Why is my Whirlpool washer not starting?
Whirlpool Washer Won’t Start – Troubleshoot and Diagnosis
- Incoming Power Problem. When something goes wrong with your Whirlpool washer, it can feel like the world is falling apart! ...
- Washer Needs Hard Reset. ...
- Whirlpool Washer Start Button Stuck. ...
- Control Lock is Turned ON. ...
- Incorrect Washer Settings. ...
- Blown Thermal Fuse. ...
- Faulty Lid Switch. ...
- Defective Control Board. ...
- Broken Timer. ...
- Faulty Motor. ...
How to fix washer lid switch?
Safety Precautions
- Unplug the Washer Start by unplugging your washer. ...
- Close the Water Supply Valves When doing washer repairs, it’s a good idea to turn off the valves that supply hot and cold water to the washer. ...
- Wear Protective Work Gloves Be sure to wear sturdy work gloves so there’s no risk of cutting your hands on the inner edges of your washer.
How do you fix the lid switch on a washing machine?
2:4710:01Broken Lid Switch Washer Repair - Kenmore or Whirlpool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd unhooked these three hooks that kind of hook on into that metal there see one two three one twoMoreAnd unhooked these three hooks that kind of hook on into that metal there see one two three one two three and then you can flip it up like that this is the lid switch. Here.
How do you bypass the lid lock switch on a Whirlpool washer?
0:522:02Lid switch bypassing whirlpool washer - How to check & fix a not starting ...YouTubeStart of suggested clipEnd of suggested clipThis is a noir style lid switch disconnect the wire harness from the lid switch. Place the jumperMoreThis is a noir style lid switch disconnect the wire harness from the lid switch. Place the jumper wire between the gray and white wires. And put electrical tape on it to insulate the connection.
How do I know if my washing machine lid switch is broken?
Signs The Lid Switch Is Bad If the lid switch is bad, the control panel of your washing machine interprets that as the lid being open. If the control panel doesn't detect the switch as being engaged, then the washer won't agitate or spin when you close the lid.
How do I reset the lid lock on my Whirlpool washer?
If your lid lock light is flashing, you can unplug your washer for 10 minutes and plug it back in to reset the washer and the flashing light. You can also press and hold the 'End of Cycle' button for 20 seconds to reset the washer and flashing lid lock light.
Will my washer work without lid lock?
NO. The lid lock it to prevent injury to the people near the washer, as without it stopping the machine, the agitator will turn with the lid open.
Can you bypass a washer lid lock?
3:216:16Washing Machine Won't Spin - Lid Switch Bypass - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I'm showing you today is how to bypass. This switch. So that the washing machine thinks theMoreSo what I'm showing you today is how to bypass. This switch. So that the washing machine thinks the lid is closed. So that you can simply drain the water out of your washing.
How much does it cost to replace a lid switch on a washer?
Washer Lid Switch Repair Cost Repairing the lid switch costs $140 to $190. In some instances, this repair might only take 15 to 20 minutes so your bill might swing towards the lower number.
How do you test a Whirlpool lid switch?
1:144:30Whirlpool / Kenmore Washer Not Draining - Lid Switch Test - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicatesMoreYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicates that the lids closed which thatlet's which is good. Now if your lips closed.
How do you check a whirlpool lid lock?
0:447:19How to Test and Replace Lid on on Whirlpool Top-load ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere turn it clockwise. Three times hit start that's manual test and the first test is the lid lock.MoreHere turn it clockwise. Three times hit start that's manual test and the first test is the lid lock. So when you get the start button like I'm doing now it's supposed to lock Leah.
How do you fix a Whirlpool lid lock?
1:053:12Whirlpool Top-Load Washer Lid Lock Replacement #W10404050YouTubeStart of suggested clipEnd of suggested clipIt pull the lid lock wires through the main top. And disconnect the wiring loom from the retainingMoreIt pull the lid lock wires through the main top. And disconnect the wiring loom from the retaining clips remove the mounting screws securing the lid lock to the main top and remove the old part.
Why does my washer keep saying lid locked?
– Lock striker that presses down on the lid switch may be out of alignment. – A piece of lint or washing machine detergent has built up over time and hinders the locking of the lid. – The control board sees an open lid switch when it attempts to lock.
Why is my Whirlpool washer stuck on lid lock?
The most common cause of a Whirlpool washer door being locked and not being able to open is a faulty lid switch (including the striker). The door switch locks and unlocks your door depending on which stage your wash cycle is at. When it becomes defective, your washer door may not unlock when it's supposed to.
How do you test a washing machine door switch?
1:292:34Washer Won't Spin/Drain? Two Terminal Switch Testing, RepairYouTubeStart of suggested clipEnd of suggested clipUse a probe to touch one of the terminals. And the other probe to touch the second terminal. NowMoreUse a probe to touch one of the terminals. And the other probe to touch the second terminal. Now actuate the switch. If the meter reading shows zero ohms of resistance. The switch has continuity.
How does a washing machine lid switch work?
When you close the lid, the strike inserts into a small opening in the cabinet top and depresses the lid switch, sending a signal to the washing machine. This safety feature keeps the washer tub from agitating or spinning as long as the lid remains open.
Why is my washing machine not locking?
Or the latch may be broken, so when you shut the washing machine door, it refuses to stay closed. In that case, the issue could be the interlock on the machine itself or the clip on the machine door. Another issue could be the hinge. Maybe it's broken, rusty, or damaged so it sticks shut and needs oiling or replacing.
Why is my GE washer not locking the lid?
Door Lock for your GE Washing Machine If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
What happens when the lid switch fails on a washing machine?
When the lid switch fails, the washing machine does not function properly. A washing machine lid switch is usually made of plastic, which is an item that can and does break. The lid switch indicates to the washing machine when it is safe to proceed to the next cycle, particularly when that cycle is possibly hazardous, ...
Why does my washing machine stop working?
This culprit for top-loading machines is responsible for several functions of the machine. When the lid switch fails, the washing machine does not function properly.
How to remove a screw from a sewing machine?
Place the screws and bolts on a surface or sectioned container in the order they are removed. Liftoff the top of the machine. Some lids have a lip on one side and may need to be slid forward and tilted up for removal.
How to turn off power on washing machine?
If necessary, scoot the appliance away from the wall just enough to expose the main power cord. Pull the cord free from the wall socket to disable the power to the washer. Do not continue until you’ve confirmed that the power cord is completely disconnected.
Do washing machines stop automatically when you open the lid?
Unlike standard washing machines, lid lock models won’t stop automatically when you open them after skirting the locking mechanism. For this reason, you’ll need to be extremely careful not to get your limbs, clothing, hair, or jewelry too close to the spinning agitator while you have the lid open.
Does Whirlpool have a lid lock?
Most newer Whirlpool washing machines come equipped with Lid Lock technology that prevents them from being opened while in use. This feature seems pretty handy—until it malfunctions and your washer refuses to run.
