
Our Dodge PCM Repair includes
- The first thing that the module is checked for is communication because that is key.
- A Visual Inspection of the ECM to check for burnt, damaged or missing components.
- We go over the symptoms you provide to us in regards to what the vehicle is doing including Diagnostics Trouble Codes.
Full Answer
How to test the PCM on a Dodge?
How to Test the PCM on a Dodge
- Prepare some important materials before you check your Dodge's PCM. Consult your OBD-II (on-board diagnostic) scanner's handbook for a list of generic trouble codes.
- Place the coding resources in your Dodge's navigation seat. Then, get into the vehicle's driver's seat.
- Locate your Dodge's computer outlet beneath the dashboard. ...
How to remove the PCM computer from your Dodge Charger?
What is the BETTER way to reset PCM?
- amc5. So I see there are a number of ways of doing this. ...
- 06powerwagon06. I've always had success disconnecting the neg battery terminal, putting the key in and turning it to start and holding it there for 15 seconds.
- xtremewlr. I'd rather be riding... ...
- MonsoonMike. ...
- Baut Baut. ...
- weedahoe. ...
- redneck153. ...
- ceri. ...
- Baut Baut. ...
- 94krawler. ...
How do I reprogram a PCM?
To restore your PC to an earlier point in time
- Swipe in from the right edge of the screen, and then tap Search. ...
- Enter Control Panel in the search box, and tap or click Control Panel.
- Enter Recovery in the Control Panel search box, and then tap or click Recovery.
- Tap or click Open System Restore, and then follow the instructions.
How to diagnose a bad PCM in a Dodge Cummins?
- Replace and program the Engine Control Module in accordance with the Service Information.
- Perform the ECM VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Engine Control (ECM) - Standard Procedure) No
- Repair the (D64) CAN C Bus (-) circuit for an open.
- Perform the ECM VERIFICATION TEST. ...

How do you test a Dodge PCM?
0:291:55PCM power and ground testing.avi - YouTubeYouTubeStart of suggested clipEnd of suggested clipConnect positive lead of the DV o M to the PCM power circuit connect. Negative lead to the batteryMoreConnect positive lead of the DV o M to the PCM power circuit connect. Negative lead to the battery positive with vehicle running or key on engine off measure voltage drop in the circuit.
Can you rebuild a PCM?
Typically, PCMs are not rebuilt in the same way that alternators and water pumps because there are no mechanical parts that wear out. Remanufacturing a PCM generally means testing the computer, isolating and repairing any faults that may be found, then retesting the computer to make sure everything works correctly.
What does a PCM do on a Dodge Ram?
The PCM–or powertrain control module–in a Dodge is responsible for controlling many of the electrical systems in the vehicle. This includes airflow to the engine, temperature and more.
Where is the PCM on a 2004 Dodge Ram?
Where is the PCM located on a 2004 Ram 3500? Under the hood on passenger side near the firewall.
What causes PCM to fail?
Water is the primary element to avoid as exposure to it can render the PCM irreparable. Other environmental factors that could lead to PCM failure include thermal stress due to excessive heat and excessive vibration that causes sensitive parts to fail.
How can you tell if a PCM is bad?
What Are the Symptoms of a Faulty PCM?Your “check engine” light is on.Other warning lights may be on, including traction control and ABS.You lose fuel economy for no apparent reason.Your car stutters when starting, requires multiple attempts, or won't start at all.Stuttering or stalling during idling.More items...•
How much does a PCM repair cost?
The PCM is a computer, and computers aren't cheap to replace. That's why the average PCM replacement cost is anywhere between $800 and $1,500, depending on the car model and labor costs. Even worse, this is almost all in the cost of the PCM itself. Labor typically only runs between $75 and $100.
How much does it cost to reflash a PCM?
Prices could range from $80 to $150, depending on the service location you choose. The process takes around about half an hour, but keep in mind that most auto-electricians charge you for at least one hour of work. PCM reprogramming is also one of the few times we'll recommend a dealership over an independent mechanic.
How do you reset the PCM?
Please see the following steps:Press and hold the PCM info button for approximately 10 seconds until the PCM reboots.Immediately select the following from the PCM CAR > OPTION > Set PCM System > Reset PCM > Vehicle Handover > Yes > Yes.
Where is the PCM fuse located?
2:114:52KIA OPTIMA PCM FUSE LOCATION REPLACEMENT, POWERTRAIN ...YouTubeStart of suggested clipEnd of suggested clipPull up on the back side you can see the fuses.MorePull up on the back side you can see the fuses.
Can I replace an ECM myself?
The parts themselves aren't inexpensive (as long as you're buying them from us!), plus high quality aftermarket and OEM ECMs can be easily installed yourself.
What is PCM and ECM?
PCM (Powertrain Control Module) – This is a combined engine and transmission control unit which will provide management and correct function of the engine and transmission from one control unit. ECU (Engine Control Unit) / ECM (Engine Control Module) – This is an electronic control unit that manages the engine only.
Can you reprogram a PCM yourself?
It's a pretty simple process and takes an hour at most to reprogram the PCM and do a system check to make sure the car's working well and there are no error codes. Can you do it yourself? Well, no, unless you have the software necessary to do a PCM reprogramming.
Can you reprogram a PCM at home?
Reprogramming a PCM requires a J2534 Pass Thru device. There are a dozen or more on the market, and some scan tools have pass thru capabilities too. To reprogram a PCM, the tool must comply with SAE Standard J2534-1. You can also use a J2534-2 pass thru tool that can reprogram other control modules as well as the PCM.
How much does a PCM repair cost?
The PCM is a computer, and computers aren't cheap to replace. That's why the average PCM replacement cost is anywhere between $800 and $1,500, depending on the car model and labor costs. Even worse, this is almost all in the cost of the PCM itself. Labor typically only runs between $75 and $100.
Who can reflash a PCM?
Historically, car dealers have been the only ones who had access to the tools and software needed to reflash PCMs. Thanks to the passing of Senate Bill 1146 in September 2000, vehicle manufacturers must now make this technology available to independent repair shops and individuals at reasonable cost.
How long does it take to repair a PCM?
If you find that PCM needs to be repaired, Solo Auto’s dedicated technicians can repair ECUs, PCMs, TCMs, and ECMs, within 24 to 48 hours, and then have your unit back in the mail on its way to you. We sell and service a variety of vehicle makes and models and we have a particular expertise with Jeep, Chrysler, and Dodge computers.
Why Would I Want To Reflash My Dodge Powertrain Control Module?
There are several reasons why you might want to reflash your Dodge Powertrain Control Module.
What if I have an older Dodge (1993 – 2003)?
While newer vehicles come with standard applications ready for owner use, older automobiles with PCM modules require code sourcing. If you have a Dodge vehicle manufactured between 1993 and 2003 and plan to install new or aftermarket sensor units, your power control module (PCM) may not recognize the new equipment. The sensors from the new equipment are sending information that’s coded in a way that the module cannot understand.
What is a powertrain controller reflash?
Powertrain Control Module reflashing is the process of replacing the existing software in a vehicle controller with new software. This is done by electronically transferring approved calibration files from a vehicle manufacturer’s website. This process is also known as ECM reprogramming, flashing, reprogramming, programming or reconfiguring.
How long does it take to reprogramme a computer?
11. Start the transfer of data. As the software is loaded, you will see a progress bar. The reprogramming procedure usually takes 30-40 minutes.
Can you do PCM on a 2004 Dodge?
Current owners of Dodge vehicles built and sold before 2004 can perform their own PCM reprogramming, but they need some specific equipment on hand as well as a digital program that is used to convey information to the module. PCM flash tools include:
Can you reinstall a GM calibration?
It’s important to note that the GM setup will not allow the same calibration to be reinstalled over itself. Only an updated calibration can be loaded into the vehicle computer. So bear in mind that there is no going back to an earlier version.
