
How to Repair a Whirlpool Gas Stove Burner Valve
- Gather Your Supplies. Always start by gathering your supplies so that you can complete the repair from beginning to end. ...
- Safety First. ...
- Disassemble the Burners. ...
- Remove the Top Panel. ...
- Access the Burner Valves. ...
- Remove the Old Burner Valve. ...
- Install the New Burner Valve. ...
- Reassemble your Stovetop. ...
- Test Your Success. ...
How do you fix a gas stove that won't turn on?
Fix your gas range burners and oven with these simple solutions that solve most problems. Most fixes are easy to diagnose and complete without calling for pro service. Remove the old igniter from the burner. Unscrew the gas stove burner if necessary. Cut or unplug the wires.
How do you replace an igniter on a gas stove?
Remove the old igniter from the burner. Unscrew the gas stove burner if necessary. Cut or unplug the wires. Reconnect the wires and attach the new gas stove igniter replacement to the gas stove burner. Reinstall the gas stove burner and push the wire connectors and excess wire down into the compartment below the oven.
How do you clean the inside of a gas stove?
Lift off the gas stove burner grate and carefully set down on a towel on the counter. Lift off the stove burner cap. Clean the under side of the burner cap with an abrasive sponge or wire brush. Using a flashlight, look down into the center of the burner.
Should I repair or replace my kitchen stove burners?
When one of your kitchen stove or cooktop burners doesn’t work, you may be tempted to pick up the phone and call in professional help for repairs. But before you write that repair check, make sure it’s not a problem that you can fix yourself.

How do you replace a gas valve on a stove?
1:455:16Whirlpool Gas Cooktop Right Front Gas Valve Replacement W10859922YouTubeStart of suggested clipEnd of suggested clipYou can now detach the old gas valve install the new gas valve by positioning it on the supplyMoreYou can now detach the old gas valve install the new gas valve by positioning it on the supply tubing and manifold align the valve bracket and secure it with the screw.
How does a gas burner valve work?
Electrical resistance from the glow bar blocks current to the gas valve, making sure that the valve closes. This decreases as the temperature increases. When the bar reaches a particular heat, enough to ignite the gas, it allows sufficient electricity through to open the gas valve.
How do you clean a gas valve?
2:077:03Cleaning & Lubricating Weber Gas Grill Valves - TVWGG - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere's a close-up of a valve there's a small silicone disc that sits on top of protects it from dirtMoreHere's a close-up of a valve there's a small silicone disc that sits on top of protects it from dirt we'll move that remove that and set it aside. And now we're going to take off the valve.
How do you clean the burner valve on a gas stove?
How to clean your gas stove burnerStep 1: Read the manual/instructions. ... Step 2: Shut off the gas. ... Step 3: Remove the burner caps. ... Step 4: Remove the burner heads. ... Step 5: Soak and scrub the removed parts. ... Step 6: Let the burner parts dry. ... Step 7: Reassemble and test the burners.
Can you fix a gas valve?
In some instances you can repair a gas valve on a furnace depending on what is causing it to not work properly. However, repairing your gas valve is not usually the most cost effective option since it can be just as expensive to have your gas valve repaired as it would be to have your entire gas valve replaced.
How do you test a gas valve?
1:058:44The simple check of the gas valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the next thing you probably want to do is check to see if there's power to the gas valve. Now theMoreSo the next thing you probably want to do is check to see if there's power to the gas valve. Now the gas valve is this doohickey right here. It's got lots of stuff on it.
Can a gas valve be cleaned?
The gas valve should be cleaned at least once in a year. You can use a soft cloth or towel to wipe and clean the gas valve. The vents of the fireplace can also become dirty, mainly due to the accumulation of dry leaves, when the fireplace is not in use. Sometimes, this can also block the vents.
How do I know if my gas valve is bad?
Here are some signs that indicate your furnace has a bad gas valve.A Gas Leak. This is a major indicator that something could be wrong with the gas valve in your furnace. ... A Total Shutdown of the Furnace. ... A Flooded Furnace. ... Get Expert Services.
Do gas valves go bad?
If the flame near the thermocouple is extinguished, the current from the thermocouple stops and the solenoid valve closes off gas flow. Although relatively rare, gas valves can fail causing a fire or explosion. Gas valves can fail from a variety of causes including contamina- tion, product deficiency, and misuse.
How do you lubricate a gas valve?
2:394:41Re-Lubrication Maintenance of a Plug Gas Valve - Boiling Point - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd basically just make a shape out of it that will fit down in the valve. Body. And then when weMoreAnd basically just make a shape out of it that will fit down in the valve. Body. And then when we thread this back in what we'll see is that it's going to force the grease.
How do you clean a stove burner ring?
Cleaning the stove rings Take two rings at a time and place them in a 2-gallon plastic bag, Ziploc bag or another storage bag with a seal. Once the rings are in, fill the bottom of the 2-gallon plastic bag with ammonia. No need to fill the bag completely. The fumes from the ammonia tackle the gunk.
How do you test a gas oven safety valve?
1:322:21Oven Not Heating? Safety Valve Testing – Gas Oven Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a probe to touch one of the valves terminals and the second probe to touch the other terminal ifMoreUse a probe to touch one of the valves terminals and the second probe to touch the other terminal if the meter reading shows a result between 0 and 5 ohms of resistance the valve has continuity.
Do all gas valves snap open and closed?
The purpose of the gas regulator at a gas burning appliance is to? Reduce the gas pressure to the proper in. WC and maintain this constant pressure at the outlet where the gas valve is fed . All gas valves snap open and closed.
How do you use a gas valve?
2:044:01How To Use The New Gas Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipClose the regulator first by turning the arm to the bottom clockwise click the arm of regulator toMoreClose the regulator first by turning the arm to the bottom clockwise click the arm of regulator to the inside horizontally.
How does thermocouple controlled gas valve?
The thermocouple responds to changes in temperature by producing an electrical current that causes the gas valve that supplies the pilot light to open when the temperature is high or to close when there is no direct heat source.
What is the role of a combination gas valve?
A combination gas valve (or combination gas control) combines in a single unit all manual and automatic control functions required for the operation of gas-fired heating equipment. In other words, a single valve replaces the various individual pilot line and main line gas controls.
Remove Burner Grate
Lift off the gas stove burner grate and carefully set down on a towel on the counter.
Put Back the Burner Cap
Place the cleaned burner cap back on. Make sure it sits perfectly flat on the burner. If it won't sit flat, try turning it until it does.
Test The Burner
Turn on the burner. You should have instant ignition and a stronger, more even flame. All the clog material broken up by the paper clip or awl will blow out with the gas pressure, allowing your gas range or stovetop burner to work like new.
How to replace a bad burner block?
If the socket looks burned, too, it may need to be replaced. You can replace a bad burner block by disconnecting the terminal wires with a screwdriver and screwing in a replacement.
What to do if your stove is not heating?
First, see if the coil is loose. When the burner coil is completely cool, reconnect it firmly into the burner socket. If that doesn’t work, pull the coil out from the socket and exchange it with another from the stove that you know for sure is working.
How to avoid damaging the burners and heating elements?
To avoid damaging the burners and heating elements, use appropriately sized pots and pans for the burner size, and avoid using extra-large or heaving cooking vessels. Don’t forget about the range hood. Be sure to clean or change the exhaust filters regularly to keep the hood working properly and for fire safety.
How to check gas line on butane fireplace?
To check for problems with the gas line, turn on a burner knob halfway, and hold the flame of a butane fireplace lighter near the burner. (Take precautions and keep your head and any loose clothing away from the burner as a flame will rise if the burner lights.)
What to do if you don't hear a click on your igniter?
If you didn’t hear a click, the igniter probably isn’t working. Using a flashlight if needed, check the small wires between the igniter and the controls to the burner compartment. If you see a detached wire, push the wire back in.
Can a switch be repaired?
Switches cannot be repaired. Choose a pan that fits the diameter of the cooking element. If you have a flat (sometimes known as glass or ceramic) cooktop, and food isn’t heating evenly, you may have the wrong sized pan for the element. Your element could be on its off-cycle.
How do I replace a gas stove igniter?
To replace the gas stove igniter, remove the screws that secure it to the burner. Then remove the wires. Some gas stove igniters simply unplug. Others, like ours, require you to cut and strip the wires and reconnect the new igniter using the special ceramic wire connectors included with the gas stove igniter (Photo 2).
How do I clean a gas stove?
Clean the gas stove igniter and burner holes if the burner won’t light. Brush the igniter with a stiff toothbrush to remove gunk. Clean out the gas stove burner holes with a needle. Learn more about how to clean a stove top. Replace the igniter control module if none of the igniters spark.
What to do if oven won't light?
First check to be sure the oven is plugged in and getting power and that the gas valve is open. If you have an older oven with a mechanical instead of a digital timer, check to make sure you haven’t bumped it off the manual setting. If your oven still won’t light, you probably need a new igniter.
Why won't my burner light?
If your burner still won’t light after you’ve cleaned the burner holes and igniter, there are three parts that could be faulty: the igniter, the igniter switch or the igniter control module. Of these, the most likely cause is a bad igniter control module. Occasionally an igniter switch will go bad.
Why does gas come up on stoves?
First gas is brought up and through your home, to where it’s burned off just right to create an even heat ideal for cooking. Then, the shear fact that food and water can so easily spill into the inner workings, it’s no wonder more problems don’t arise on your stove to gum up the works.
Why does my gas stove make a roaring sound?
Anything else such as short or flat or yellow/orange in color, or making a “roaring” sound, then there is in imbalance of air and gas mixture. You can adjust what’s called an air-shutter (another important part to check when repairing a gas stove), on each burner.
What happens if a match doesn't light the burner?
If a match won’t light the burner, then there is no gas getting to where it needs to be. Check that the gas shut-off valve is in the open position – under the stovetop – handle must be in line with the pipe. You can try loosening the gas connection to the stove very slowly and carefully.
Do you have to have a gas stove in working order?
If you cook every day, then having all your gas stove parts in working order is important. If they aren’t, you’re likely to face a break down somewhere. There are a lot things that are going on when you cook on a gas range.
