How to repair a not working ice maker in the Amana refrigerator?
- 1. Control Lock is on. This deactivates the dispenser controls and comes in handy around small children or pets and while you’re cleaning the area. If ...
- 2. Using a reverse-osmosis system. This could lower the water pressure. See tips for using a reverse-osmosis system here.
- 3. Kink in the water supply line. This can reduce water flow and cause water and ice to dispense slowly or stop dispensing. Straighten out the line to ...
- 4. Saddle valve is incorrect. This will lead to low water pressure. Be sure to use a ¼-inch type valve that requires a drilled hole. It is not ...
Full Answer
How do I Fix my Amana refrigerator ice maker not working?
If it works you saved money on your Amana refrigerator ice maker repair. However, if it is still not working properly you may need to begin troubleshooting the unit. Start by turning off the water supply. Next look over the water connection to the ice maker.
When should you replace the ice maker Assembly on a refrigerator?
Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly.
Why is my ice maker not working on my Kenmore refrigerator?
One component of the ice maker assembly might be defective. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly. Before replacing the ice maker assembly, check the water inlet valve, water line, and fan.
How do you test an ice dispenser on a whirlpool refrigerator?
The water inlet valve supplies water to the ice and water dispenser. The water inlet valve requires a minimum of 20 psi to function properly. Check the water flow and test the pressure to determine if it is at least 20 psi. The door switch turns off the ice and water dispenser when the refrigerator door is open.
How do you reset the ice maker on an Amana refrigerator?
0:422:08My Amana Refrigerator Ice Maker is Not Working! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhich should be located on the right side of the icemaker. If the arm is raised it means it isMoreWhich should be located on the right side of the icemaker. If the arm is raised it means it is turned off by lowering the arm you will turn it on this may be the cause of your problem.
Why is my Amana fridge not making ice?
Make sure “water” or “ice” has been selected. Also make sure the water supply is properly connected to a cold water supply and the water shutoff valve is fully opened. If the issue is ice, make sure the ice maker is turned on and the ice storage bin is properly in place.
Where is the off switch for an Amana ice maker?
The On/Off switch is located on the bottom of the ice maker, which can be accessed by lifting and opening the ice maker door.
How do you reset an ice maker?
Unplug the machine and wait 10 seconds. Plug the machine back in and press the ON button. You should see a blue light appear, letting you know that the machine has been reset.
Why will my ice maker not work?
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How do you clean Amana ice maker?
Use a washcloth and warm soapy water, or a couple tablespoons of baking soda dissolved in a gallon of warm water, to wash and wipe any of the removed parts. Rinse well and set aside to air dry; they will need to be completely dry before they're returned to the unit.
Is arm up or down to make ice?
If the wire arm of your ice maker is in the up position, this signifies to the ice maker that the ice storage bucket is full and turns the ice maker off. If you would like your ice maker to continue making ice, the arm lever should be in the down position.
How do I fix my ice maker ARM?
1:352:47How To: Whirlpool/KitchenAid/Maytag Ice Maker Shut Off Arm W11342242YouTubeStart of suggested clipEnd of suggested clipWe're going to line it up with the icemaker head right here and push it into the opening. Once youMoreWe're going to line it up with the icemaker head right here and push it into the opening. Once you have it pushed all the way in we can reach back and snap the other end into the filled cup.
How do I know if ice maker is working?
Make sure the icemaker is plugged in and turned on....To check if the icemaker itself is working:If the icemaker mold is empty, you can manually pour about 4 ounces of water in the icemaker mold.Wait about 2 hours.If the icemaker has dropped ice cubes out from the mold, you know the icemaker itself is working.
How do I force my ice maker to cycle?
If your gear has a small notch in it, then you may need a flat-head screwdriver. Use it to turn your gear counterclockwise until you hear the mentioned click. In both situations, the click that is heard will force the ice maker to cycle.
Why does my water dispenser works but not ice maker?
If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi.
How long does it take for ice maker to reset?
Leave the refrigerator unplugged for 5 minutes. This will allow the ice system to reset. After 5 minutes, replug the refrigerator and turn the switch back on. This should cause the ice maker to start working again.
How long does it take an Amana refrigerator to make ice?
It can take up to 2 - 3 days (depending on usage) to completely fill the ice bin. Ice maker is located in the upper left corner of the refrigerator compartment and the ice bin is located on the door. This type of ice maker should produce 100 - 140 cubes, during normal operating conditions.
How do you change the water inlet valve on an Amana refrigerator?
0:063:11Amana Refrigerator Repair – How to replace the Water Inlet ValveYouTubeStart of suggested clipEnd of suggested clipThe power to it simply pull the plug from the receptacle. Next we're going to shut off the waterMoreThe power to it simply pull the plug from the receptacle. Next we're going to shut off the water supply to the valve and disconnect the inlet to the valve.
Where is the water filter in my Amana refrigerator?
0:030:32How To Change Your Amana Side By Side Filter - YouTubeYouTubeStart of suggested clipEnd of suggested clipItself what we're gonna do is open the door to the freezer. There's a little door right here justMoreItself what we're gonna do is open the door to the freezer. There's a little door right here just push the door. And out pops the filter that's all you need to do put it back in.
How do I fix my ice maker ARM?
1:352:47How To: Whirlpool/KitchenAid/Maytag Ice Maker Shut Off Arm W11342242YouTubeStart of suggested clipEnd of suggested clipWe're going to line it up with the icemaker head right here and push it into the opening. Once youMoreWe're going to line it up with the icemaker head right here and push it into the opening. Once you have it pushed all the way in we can reach back and snap the other end into the filled cup.
What is an ice maker inlet valve?
The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. If t...
How does an ice maker work?
The icemaker module is equipped with a motor that cycles the ice ejector arms or turns a tray to eject the cubes into the ice bucket. When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes. At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water. If the icemaker module is defective, the ice maker won’t make or dispense ice. First, depending on your model, make sure t...
What to do if icemaker has ejector blades?
If the icemaker module has ejector blades, check to ensure that ice cubes are not stuck in the blades. There are usually test points in the module that a technician can use to further diagnose problems with the module.
How much pressure does an ice maker need?
As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve.
What temperature should an ice maker be?
The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear ...
How much pressure does a water inlet valve need?
The water inlet valve supplies water to the ice and water dispenser. The water inlet valve requires a minimum of 20 psi to function properly. Check the water flow and test the pressure to determine if it is at least 20 psi.
What to do if freezer temperature is too high?
If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed.
