How to Fix a Kitchenaid Refrigerator Ice Maker Not Working.
- 1. Check the temperature. Kitchenaid recommends that the freezer temperature be set to zero and the refrigerator temperature be set to 37 degrees ...
- 2. Check the water supply line.
- 3. Check the water inlet valve.
- 4. Check the water pressure.
- 5. Check for a frozen water supply tube.
Full Answer
How to fix an ice maker on a KitchenAid refrigerator?
If the ice maker is on, but disconnected to water supply line, the following could happen:
- The ice maker will continue to try to make ice, causing a buzzing sound
- A refrigerator section may to be too cold
- Food in crisper drawers may freeze
How do I fix the ice maker in my Refrigerator?
If your ice maker has frozen up, take the following steps to thaw it out:
- Unplug the refrigerator or turn off the circuit breaker that supplies power to it. ...
- Find the fill tube. ...
- Warm the hose and surrounding mechanism. ...
- If you don’t want to use a hair dryer, you can soak the supply tubing with hot water, using a turkey baster and catching the overflow in a bowl. ...
How to troubleshoot a KitchenAid superba refrigerator icemaker?
How to Troubleshoot an LG LRSC26925TT Ice Maker
- Working With Water. Inadequate ice supply, misshapen ice cubes or failure to operation may occur as a result of water issues.
- Ice Issues. To prevent odd-tasting ice, dispose of the first 20 cubes produced after you first install the LRSC26925TT.
- Filter Fixes. ...
- Power Problems. ...
How to defrost KitchenAid refrigerator?
To force defrost a KitchenAid refrigerator, do the following:
- Open the door of the refrigerator and press the button for the door alarm and hold it.
- Now, press the button that reduces the temperature for the refrigerator section (refrigerator down button) and hold the button.
- Release the button for the door alarm and after about 3 seconds, the code Fd will appear on the display on the left.
Why did my KitchenAid ice maker stop working?
If your KitchenAid ice maker won't make ice the cause may be a defective water inlet valve. The water inlet valve is electric and requires adequate water pressure to function. If you have a faulty valve or there is not enough water pressure, the valve won't open and the ice maker won't fill with water.
How do I reset my KitchenAid refrigerator ice maker?
Shut the freezer door and allow it to reset for 10 seconds before opening the door. Press the door's switch three times and shut the door. Let it sit for a few seconds to reset the ice maker. This should stop the blinking lights.
What would cause my ice maker to stop working?
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How long do KitchenAid ice makers last?
A safe estimate would be roughly 4 to 5 years, or within the warranty of the machine. But beyond the warranty there is no guarantee. To extend the life of your ice machine, make sure you perform routine maintenance and cleaning. It's not uncommon for a machine to die early as a result of poor maintenance.
Can water filter cause ice maker not to work?
While a clogged water filter could be the cause of your ice maker not working, there are more common causes. First, make sure that your icemaker is simply turned on and plugged in. Check the power cord and make sure it is plugged in. Take a look at the feeler arm or paddle to confirm it can move freely.
How do I force my ice maker to cycle?
If your gear has a small notch in it, then you may need a flat-head screwdriver. Use it to turn your gear counterclockwise until you hear the mentioned click. In both situations, the click that is heard will force the ice maker to cycle.
How do I manually reset my ice maker?
Unplug the machine and wait 10 seconds. Plug the machine back in and press the ON button. You should see a blue light appear, letting you know that the machine has been reset.
Why is my ice maker not dropping ice?
Ice Clumps in the Bin One of the most common – and innocent – causes of an ice maker that won't dispense ice is that an ice clump has formed inside. In order to drop the ice cubes from the mold, heat is released to lightly melt them.
Where is the reset button on ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
Can an ice maker be repaired?
0:207:47Ice Maker Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipEvery part of the ice maker for damage. Especially the Teflon coated ice mold which is common toMoreEvery part of the ice maker for damage. Especially the Teflon coated ice mold which is common to break down and corrode I hate to say it but because ice makers have such a short life expectancy these.
How much does it cost to fix an ice maker in a refrigerator?
On average, icemaker repairs will cost about $330. However, before calling a repairman about your malfunctioning ice maker, check to see if the hose is frozen. A frozen hose can be thawed out in warm water, and this could restore function to your ice maker.
How much does it cost to replace an icemaker in a refrigerator?
around $300 to $450The cost to replace a refrigerator's ice maker is around $300 to $450 for the replacement unit and labor costs of hiring a local refrigerator repair specialist.
How do I reset my KitchenAid side by side ice maker?
Close the freezer door and let it reset for 10 seconds prior to opening the door. Tap the door's switch at least three times and close the door. Allow it to sit for a few seconds to restart the ice maker. It may cease the blinking lights.
Is there a reset button on a KitchenAid refrigerator?
Yes, KitchenAid refrigerators will have a reset button. Typically, you can find this by locating the ''water filter' or 'filter reset' button and holding them down for a few seconds.
Where is the ice maker switch on KitchenAid fridge?
Can you turn the ice maker off? To turn the ice maker on/off: Open the freezer door and turn off the ice maker. The On/ Off switch is located on the top right side of the freezer compartment.
How do I reset my KitchenAid French door refrigerator?
Before you start troubleshooting or changing the components of the refrigerator, try to reset the error by turning off the KitchenAid refrigerator for just ten minutes. It resets the control panel and fixes the problem.
How to replace ice maker control module?
To secure the component, rethread its screws, reconnect its wire harness, and place the shutoff arm into the hole on the back of the housing. Then, replace the control module cover.
What happens when the temperature is cold enough?
When the temperature is cold enough, the thermostat sends a message to the control module to dump the ice out of the mold and begin filling the mold with water to make new ice. If the thermostat is faulty, it will not properly detect the temperature inside the ice mold, meaning no new ice will get made.
How to access control module on ice maker?
To access the control module, place the ice maker assembly on a flat surface, and remove the cover located at the front of the assembly. Behind the cover, you’ll find the control module. Before you can remove the module, disconnect the wire harness that runs to the back of the component.
Where is the thermostat on an ice maker?
The ice maker thermostat sits on the backside of the control module housing. To remove the thermostat, push on the pins sticking out of the front of the housing.
Can a Kitchenaid ice maker malfunction?
Who doesn’t love the convenience of an ice maker? Unfortunately, like any other mechanism, your KitchenAid refrigerator model KSCS25INSS00 ice maker can malfunction, meaning you’re left trying to pinpoint the component causing the issue. If you’re dealing with an iceless, ice maker, there’s a good chance either the control module or the ice maker thermostat is faulty. Luckily, replacing the broken part will have your ice maker up and running in no time.
What to wear to repair ice maker?
Wearing gloves and safety goggles will protect your hands and eyes while you work to repair your ice maker.
Do thermostats need alumilastic?
In order for the thermostat to work properly, you’ll need to place a small amount of alumilastic on the back of the part.
Is the ice maker turned on?
Verify that the ice maker is turned on. If the ice maker’s water supply is not connected to water supply line, turn the ice maker off. If the ice maker is on, but disconnected to water supply line, the following could happen:
Was the water system flushed after filter installation or replacement?
Flush the system is needed every time the filter is changed or once the refrigerator is installed to the water supply line for the first time. Air in the water system may cause dripping at the dispenser or small/hollow ice cubes.
How to fix ice maker that is jammed?
First, ensure that ice is not jammed in the ejector arm of the ice maker. Remove jammed ice from the ejector arm using only a plastic utensil so the ice maker is not damaged. This will likely resolve the issue. Because the ice may not be completely frozen yet, when the harvest fingers try to harvest the ice cubes, the fingers bring up icy water that attaches to the stripper. This icy water can then freeze on the stripper during the next cycle causing an ice bridge. This ice bridge will cause the harvest fingers to jam.
What happens if the ice maker is on but disconnected?
If the ice maker is on, but disconnected to water supply line, the following could happen: The ice maker will continue to try to make ice, causing a buzzing sound. A refrigerator section may to be too cold.
What causes ice to be thin?
A clogged or incorrectly installed water filter will reduce the water flow to the ice maker and could cause thin, low or no ice production.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
My Repair & Advice
I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy.
My Repair & Advice
SO I FIGURED THAT ALL THE MECHANICAL PARTS OF IT WERE FINE SO THE LOGICAL THING TO DO WAS TO REPLACE ELECTRICAL COMPONENTS WHICH CONSISTED OF THE THERMOSTAT {THE BRAIN} AND THE CONTROL MODULE WHICH I PURCHASED AT A VERY REASONABLE PRICE . I REASSEMBLED THE UNIT AND IT HAS BEEN WORKING LIKE NEW EVER SINCE. THANK YOU!
My Repair & Advice
It was a relatively easy fix and the video instructions on this site provided were helpful. The one piece that wasn't clear is the alumilastic was already on the replacement part so a separate tube is not required. That wasn't clear on the video and was an unneeded expense.
