Check the rear counter-balance spring, I find that breaks more than anything else for this issue. The rear spring hooks in a hole on the back of the base. Sometimes this hole rusts through. Simply drill a new hole in the base right next to the other hole.
Full Answer
How to troubleshoot a Kenmore 80 series washer?
If Kenmore Washer is Leaking, Check:
- Drain Pump. The drain pump can begin leaking water if it’s damaged, cracked or some of the hoses connected to get loose.
- Tub bearings Seal. The tub seal can become torn, thus causing water to leak from around the seal. ...
- Drain Hose. Check the drain hose on your washer to ensure it’s not leaking. ...
- Water inlet valves. ...
Does a Kenmore series 80 washer have a drive belt?
Your Kenmore washer does not use a drive belt. You have a direct drive washer meaning it has no belt. Your washer uses a motor coupler to connect the motor to the gear case. If the motor coupler breaks your washer will run but it will not agitate nor spin and only drain. Beside above, does a Kenmore 90 Series washer have a belt? No!
How to disassemble Kenmore washer?
Fix Your Kenmore Stack Washer
- What Went Wrong... To give a little background this washer was making loud banging sounds as it ran (see the video above.)
- Open Wide! There are 2 screws on the bottom of the front panel. ...
- Here's the Problem. Looking under the drum I could clearly see that the belt was damaged. ...
- Replacing the Belt. ...
- It's Fixed!! ...
How do you troubleshoot the Kenmore 80 series clothes washer?
- The belt is broken, loose, or frayed. The belt transfers the power from the motor to the drum. ...
- The motor. If the machine is completely silent, meaning there isn’t a hum when you close the lid, it could be the motor that needs replaced. ...
- The lid/door switch. The switch has to be activated to let the motor activate. ...
How do I reset my Kenmore 80 series washer?
1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Why is my Kenmore 80 series washer not draining?
If the drain pump is clear of obstructions, but is still noisy during the drain cycle, replace the drain pump. Sometimes, socks and other small articles of clothing can get into the drain system and clog the pump hose or the pump itself. Remove the hoses from the pump and check for any obstructions.
Is it worth repairing a Kenmore washing machine?
As a general rule, if it costs less than 50% of the price of a new washing machine to repair your old one, you should choose the repair option. But, you should also consider whether or not there is a warranty coverage on your washer and think about economic realities.
What year is Kenmore 80 series washer?
The second letter indicates the year the appliance was made. For example, the F in the 80 series washing machine serial number CF4227224 indicates the machine was manufactured in 1996. The L in the serial number CL2636932 for a 70 series washer indicates the machine was made in 2001.
How do I manually drain my Kenmore 80 series washer?
Squeeze the locking pin on the end of the drain hose that is connected to the back of the washer if you will be draining the water into a floor drain. Pull the hose away from the washer to disconnect it. The water will pour out as soon as the hose is disconnected.
How do you fix a Kenmore washer that won't drain or spin?
0:086:44Washer Won't Drain or Spin: Troubleshooting VMW and Direct ...YouTubeStart of suggested clipEnd of suggested clipTurn the Machine off pull the drain hose out of the standpipe. And check for a clog at the end ofMoreTurn the Machine off pull the drain hose out of the standpipe. And check for a clog at the end of the hose. Sometimes lint or debris can build up in this area and prevent draining.
How long do Kenmore washers last?
Kenmore washing machines have been known for their longevity. Kenmore washers can last for more than a decade. On average, Kenmore washers should last for at least 10-13 years.
What is the average lifespan of a washing machine?
10 to 13 yearsWashing Machine Lifespan The average life of a washing machine ranges from 10 to 13 years, although some brands can manufacture washing machines with an even longer lifespan than the average appliance.
How many years should a washer last?
around 10 yearsWashing machines, on average, last around 10 years, according to Consumer Reports. If your washer is reaching the threshold, or it's been having some problems, here are some signs the end may be near.
What would cause a Kenmore washer not to spin?
If the clutch is worn out, it may prevent the tub from spinning. If the clutch band kit is worn out, replace it. The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning.
Who made Kenmore 80 series washer?
The Kenmore 80 Series is a washing machine sold by Kenmore, a Sears-owned brand of household appliances.
Is there a recall on Kenmore washers?
The recall affects several LG and Kenmore Elite Brand top-loading washing machine models. The CPSC says an unbalanced load in those models can cause the washing machine to shake excessively and the drum to come loose during use, posing a risk of injury to consumers and property damage to the surrounding area.
How do I clean the filter on my Kenmore top load washer?
0:163:13How to Clean Washing Machine Filter Kenmore - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the filter is usually located on the bottom left-hand side of the washer. Itself right behindMoreAnd the filter is usually located on the bottom left-hand side of the washer. Itself right behind this door so first be sure to put down your paper towels then open up the access door.
How do you reset a Kenmore washing machine?
How to Reset a Kenmore Elite HE WasherPress the "Stop" button twice, and then press the "Power" button. Video of the Day. ... Choose a wash cycle (e.g. "Normal"), and then choose your wash options (e.g. "Hot/Cold" or "Cold/Cold").Press the "Start" button to complete the reset process and restart the washing machine.
Where is the lint trap on a Kenmore washing machine?
Where Is the Lint Trap on a Washing Machine?Along the top rim of the washer drum: Slide your fingers around the top of the washing basin, and you may run into a screen, which you can pull out to remove lint. ... Inside the center agitator: If you have a top-loading washer, inspect the center agitator.More items...•
Does Kenmore 80 series have a belt?
Install the replacement belt around the drum of your Kenmore 80 series dryer. Remove the old belt and move the replacement belt into the belt track on the drum. The belt will be a bit too large for the drum until threaded through the motor at the bottom right of the dryer.
Why won't my washer spin?
If your hose is clogged, this will result in your washer not entering the spin cycle because it doesn’t have adequate drainage. Also, if your hose is kinked, this will cause the same problem. In this case, you will need to pull the washer out and look in the back for a kinked hose. If the hose isn’t kinked, check to see if it’s clogged.
How to keep a washer from spinning?
If it looks okay, check to make sure that the lid is triggering the button, because if it’s not, this will keep your washer from spinning.
What happens if your washer is not level?
Sometimes if your washer is not level, it affects the bearings, which are what keeps your tub steady during the agitation and spin cycles. If it’s not level, you will need to adjust it by pulling out each leg to ensure its level.
Why does my washer stop spinning?
So, if the rotor is damaged, this will cause the electromagnetic field not to be as strong, which then will stop your washer from spinning. By replacing your rotor in the event it’s damaged, you can fix the problem.
What happens when the lid is closed on a washer?
When the lid is closed, a button that’s triggered lets the machine know the cover is shut. If this mechanism isn’t getting appropriately triggered, this will keep your washer from going into the spin cycle.
Why does my washer smell hot?
However, a drive motor problem will produce a burning smell like a hot wire or hot metal. If you smell something like this, it’s most likely due to a defective drive motor.
Why does my washer shut down?
Your motor control board is what helps give power to your motor. This fragile component also regulates the spin speed, so if it’s not working , then your washer may not enter the spin cycle. Eventually, this will cause your washer to shut down completely.
