Home Repair: How to Fix Kitchen Cabinets
- Build a Shelf That Won't Sag. ...
- Replace Worn-Out Drawer Slides. ...
- Adjust Euro Hinges. ...
- Silence Banging Doors with Bumpers. ...
- Fill In Stripped Screw Holes. ...
- Beef Up Wimpy Drawer Bottoms. ...
- Glue Loose Knobs. ...
- Renew the shine. ...
- Repair Busted Drawers. ...
- Repair a broken drawer front. ...
How to replace a sink base cabinet floor?
How to Replace a Sink Base Cabinet Floor Remove the middle section. Drill a 3/4-in. hole in each corner of the traced cutout line. Then run your jigsaw along the... Drop in the new floor and screw it into place. Predrill holes around the perimeter using a countersink bit. Then install... Caulk ...
How do you fix a broken screw in a kitchen cabinet?
Insert the glue-covered end of the toothpick into the damaged screw hole. Repeat the process with more toothpicks if the hole is large. Let the glue dry for several hours. Break off each toothpick so it is flush with the cabinet surface. A craft knife comes in handy for cutting them if they don't break cleanly.
How do you fix a leaky sink base?
The flimsy particleboard bottoms in most kitchen and bathroom sink bases are often swollen and moldy from leaks. The best fix is to cut them out and replace them. Let’s face it—it’s easy to get water on the floor of your sink base cabinet.
Should I refinish or replace my Kitchen cabinets?
Refinishing shouldn't be necessary unless there is water damage, which you can usually fix with light sanding with fine sandpaper and a touch-up coat of paint or stain followed by an application of clear finish. For some damaged cabinets, it's better to call a cabinet repair company or cabinetmaker to handle the repairs.
How to hide scratches on kitchen cabinets?
How do I fix a drawer?
How do I replace a door catch?
What to do if your slides are bent?
How to adjust hinges if they don't have depth screws?
How to fix loose nails?
See more
About this website
How do you repair the bottom of a cabinet?
2:123:30How to replace rotted sink base cabinet floor bottom. Easy! Home ...YouTubeStart of suggested clipEnd of suggested clipCut ours at about 21 place the board's in the cabinet. And fit the seams together. If you cut itMoreCut ours at about 21 place the board's in the cabinet. And fit the seams together. If you cut it upside down you can have a nice finished cup without splintering. I'm using quarter-inch. Plywood.
How do you fix a water damaged base cabinet?
3:474:59Damaged sink cabinet floor -- How to fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipLevel so the best thing i can suggest that we do is just take some silicone or some caulking.MoreLevel so the best thing i can suggest that we do is just take some silicone or some caulking.
How do you fix a sagging bottom cabinet?
If your cabinets are really sagging, use more shims. You can add two sheets of shim behind each hinge. If the sagging is less, place one sheet behind the hinge. Add as many shims until it is fixed.
How do you fix kitchen baseboards?
2:207:00How to remove and replace damaged baseboards - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver from another part of the house just so it matches. The first thing I'm going to do is pull outMoreOver from another part of the house just so it matches. The first thing I'm going to do is pull out the nails you want to pull out the nails from the back.
How do you repair water damaged wood under kitchen sink?
0:538:55Rotted Sink Cabinet Floor--How To Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is specifically sand apply which is Home Depot's brand of plywood it's cheap it's almostMoreThis is specifically sand apply which is Home Depot's brand of plywood it's cheap it's almost cabinet great it looks good when it's painted.
How do you fix steam damaged kitchen cabinets?
0:061:20How to Repair Steam and Water Damage on Kitchen CabinetsYouTubeStart of suggested clipEnd of suggested clipWhich is your beeswax. Take your touch of beeswax. This will go a long ways you can do a wholeMoreWhich is your beeswax. Take your touch of beeswax. This will go a long ways you can do a whole kitchen with this product right here in that pint bottle buff it into those dry.
How can I strengthen my kitchen cabinets?
A thick plywood sub-top fitted over the cabinets before new countertops are laid can help distribute weight evenly over a large area. Alternately, angled iron hardware can be used inside cabinets for a discrete but sturdy reinforcing job.
How do you brace kitchen cabinets?
4:567:28Hang Upper Cabinets by Yourself - Cabinet Brace How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipI get the opposite side of the cabinets that plumb and shim as required. Then they drive the screwsMoreI get the opposite side of the cabinets that plumb and shim as required. Then they drive the screws on that side and do one last check the level and plumb.
How do you reenforce kitchen cabinets?
0:597:58How to: Reinforce Older Cabinets before installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipOur long we'll pre-drill some holes. And screw into that one before all the way across the top andMoreOur long we'll pre-drill some holes. And screw into that one before all the way across the top and it down the side you know three and a half inches okay and then when we attach it to the wall.
How do you replace baseboard under cabinets?
How to Replace Kitchen Cabinet Base MoldingPry the Molding Loose. Place the tip of a screwdriver at any joint or mitered edge of the base molding. ... Remove the Molding. ... Remove Nails, Glue and Splinters. ... Cut a Reverse Miter on the New Base. ... Use a Tri-Square. ... Cut the Molding. ... Attach the Molding. ... Sand the Molding.
How do you fix kitchen cabinets that are peeling?
InstructionsPull Back the Thermofoil Layer. Have a helper hold the peeling thermofoil away from the MDF. ... Scrape the Cement. Scrape away dried cement from the MDF core.Apply the Contact Cement. ... Wait to Press. ... Press Together and Secure. ... Clean Up.
How do you replace a section of baseboard?
0:3016:24How To Fix Damaged Baseboard, Crown Moulding And Trim Like A ...YouTubeStart of suggested clipEnd of suggested clipYou're gonna have some brad nails get a new baseboard. Put it over there brad nail it you should beMoreYou're gonna have some brad nails get a new baseboard. Put it over there brad nail it you should be done and that should be the end of the video.
How do you fix a swollen kitchen cupboard?
Sand down the swelled particleboard, using a pad sander and 100-grit sandpaper. Apply contact cement to the flattened particleboard and the back of the laminate and let it set for five to 10 minutes. Press the laminate into place and clamp it down with C-clamps. Leave it clamped overnight.
How do you fix water damaged MDF cabinets?
1:112:39repairing water damaged MDF cabinets - YouTubeYouTubeStart of suggested clipEnd of suggested clipI got two coats of primer. And now we just filled it. And sometimes there's a like a body fillerMoreI got two coats of primer. And now we just filled it. And sometimes there's a like a body filler bondo type thing but today I'm using this plastic wood it's not less moisture to it.
Can you fix swollen MDF?
MDF in its undefiled manufactured state is stable and consistent. When it gets wet, it swells and distorts. Swells can be sanded down if the MDF hasn't crumbled or separated to any extent.
How To Repair Wood Cabinets – Dents and Scratches
Awesome tips. Just to add up. Stain-filled markers and pencils are available in many shades. Because scratches tend to absorb a lot of stain, we suggest starting with a color slightly lighter than your wood, then switching to a darker shade if needed.
How to fix a broken cabinet?
Start by checking for separating bracing. If you find any, it means you may need to have the old braces taken down and reset with new screws and glue. The screws will draw your cabinet together and make it easier to restore stability. 3. Replace Damaged Parts.
What to do when a cabinet is dry?
Once the cabinet is dry, you can evaluate the damage further, and gather supplies. As a general rule, it’s smart to have carpenter’s glue, clamps, and screws on hand. Keep in mind that a professional will carry these items if you intend to hire one.
Why are my kitchen cabinets wet?
This will depend, in large part, on whether your cabinets got wet due to a burst pipe, high humidity, or leaking water.
Can water damage kitchen cabinets?
Over time, water can destroy the outer shell of your kitchen cabinets, damaging the finishing and darkening the wood. In some cases, water damage can also render your cabinets useless, especially in cases where you’re dealing with a water leak in the cabinets under your kitchen sink, or a similar issue. If your cabinets are made of material like ...
Is laminate good for kitchen cabinets?
Laminating is an effective way to protect cabinets and change the looks of your kitchen, but it doesn’t completely waterproof the cabinets. The following tips also help protect kitchen cabinets from water damage. Caulk Seams – Keep sinks from leaking around edges by caulking seams between sink edges and countertops.
What to do if your cabinet is warped?
For instance, if a cabinet shelf, drawer box or any of the doors and drawers have warped, you usually need a cabinetmaker or carpenter.
How to get a close color match on a cabinet?
Start with a color slightly lighter than the cabinet's finish and then layer darker markers until the scratch is no longer obvious. Test markers in an inconspicuous area first to ensure a close color match. 2.
Why won't my cabinet door close?
A cabinet door that doesn't close or that doesn't stay closed is often caused by a problem with one of the hinges. Check the hinges to see if any of them are loose or no longer flat against the cabinet or cabinet door. If a hinge is loose, the most common cause is a loose screw or two.
What is a fill stick for cabinet?
A fill stick, available at most hardware stores, comes in handy for filling tiny holes, such as old screw holes or gouge marks on a door or drawer front.
Do you need to paint scratches on kitchen cabinets?
Minor scrapes and scratches on kitchen cabinets and countertops usually don't need paint or stain and are simple enough to be a DIY home improvement project with very little out-of-pocket expense. If you still have the original literature that came with your cabinets, look for the manufacturer and any information about the cabinet finish. Check with the original retailer or on the manufacturer's website for a touch-up kit or scratch-repair marker that matches your type of finish. Some cabinet retailers even include these with the cabinets since minor dings are bound to happen during the installation process.
Can you replace a cabinet door with a manufacturer part?
If a cabinet door or box is beyond a simple repair, it's usually easiest and cheapest to simply replace it with a manufacturer part, but if the cabinets were custom built, you may need to have a skilled carpenter or cabinetmaker craft an identical replacement part.
How do I replace a door catch?
Adjustment is just as simple, but you might have to readjust the catch a couple of times before you get it right. Loosen the screws, move the catch in or out, and tighten the screws. If the door doesn’t close tightly, try again.
How to adjust hinges if they don't have depth screws?
If your hinges don’t have depth screws, start with the side screws. second. If the door is crooked—not standing parallel to adjacent doors or square with the cabinet—adjust the side screw. This moves the door from side to side. In some cases, you have to loosen the depth screw slightly to adjust the side screw. third.
How do I adjust a door that isn't flush with the door?
First: If the door isn’t flush with the doors next to it, adjust the depth screw. This screw moves the door in or out. Some depth screws move the door as you turn them. But with most, you have to loosen the screw, nudge the door in or out and then tighten the screw.
How to clean a cutting board with salt?
Photo 1: Apply lemon and salt. Scour the cutting board with a lemon and kosher salt until the board is clean. Photo 2: Add mineral oil. Apply mineral oil to the board and wipe off the excess. After a few hours, apply a second coat.
How to get rid of stains on wood?
Simply scour the board with a lemon and a pile of kosher salt, then apply mineral oil. The coarse kosher salt is an excellent abrasive, and the citric acid kills bacteria. When the stains are gone, rinse the board and let it dry. Mineral oil helps prevent the wood from absorbing stains.
How do I cut a cabinet base?
Swing the blade of a miter saw to 45 degrees. Place the flat side of the molding against the miter saw fence. Cut down through the molding so that the face of the molding is cut away by the blade. The long point of the miter should be on the back.
How do I install base molding on a wood floor?
Place the base molding on the floor against the toe-kick. Slide the long point of the miter into the corner. Hold the molding in place and make a mark on the opposite end of the molding if it goes around an outside corner. Mark along the back of the molding at the corner of the toe-kick. Use a tri-square to continue the line on the back of the molding to the top.
What is the toe kick on a cabinet?
This part, also known as the toe-kick is often shimmed up off the floor to level the cabinet. This leaves a gap between the bottom of the cabinet and the floor. Base molding spans over it to complete the cabinet installation. It is attached to the toe-kick with pin nails and mitered in the corners just as molding is elsewhere in the home.
How to remove a broken molding?
2. Insert the tip of a flat crowbar behind the molding. Pull on it with one hand as you pry on it with the other. If it breaks, that's okay. Force the tip of the crowbar under the broken part and continue prying and pulling the molding off until it's all removed.
How to drive a screwdriver through a molding?
Place the tip of a screwdriver at any joint or mitered edge of the base molding. Use a hammer to drive the tip of the screwdriver behind or between two pieces of molding. Pry one of the pieces loose with the screwdriver.
What to do if your sink is leaking?
The flimsy particleboard bottoms in most kitchen and bathroom sink bases are often swollen and moldy from leaks. The best fix is to cut them out and replace them.
Can you cut out the bottom of a sink base cabinet?
We’ll never understand why cabinetmakers use particleboard for the base, but they do. And once it starts swelling, your only option is to replace it. But you don’t have to cut out the entire bottom.
How to hide scratches on kitchen cabinets?
If you have shallow scratches or nicks, hide them with a stain-filled touch-up marker. Dab on the stain and wipe off the excess with a rag. But beware: Scratches can absorb lots of stain and turn darker than the surrounding finish. So start with a marker that’s lighter than your cabinet finish and then switch to a darker shade if needed. For deeper scratches, use a filler pencil, which fills and colors the scratch.
How do I fix a drawer?
How to Fix a Drawer: Remove fasteners and old glue. Don’t put up with a broken corner joint on a drawer. Fix it before the whole drawer comes apart. Remove the drawer and then remove the drawer front from the drawer box if possible.
How do I replace a door catch?
Adjustment is just as simple, but you might have to readjust the catch a couple of times before you get it right. Loosen the screws, move the catch in or out, and tighten the screws. If the door doesn’t close tightly, try again.
What to do if your slides are bent?
To keep the project simple, buy new slides that are identical (or almost identical) to the old ones. That way, replacement is an easy matter of unscrewing the old and screwing on the new.
How to adjust hinges if they don't have depth screws?
If your hinges don’t have depth screws, start with the side screws. These move the door from side to side. In some cases, you have to loosen the depth screw slightly to adjust the side screw. Perfect one door before adjusting the second.
How to fix loose nails?
Remove nails, staples or screws from the loose joint and scrape away old glue with a utility knife. Predrill nails holes and glue the joint. Predrill 1/16-in. holes for nails, apply wood glue to the joint and nail it together with 1-1/2 in. finish nails.
