Repairing Guides

how to repair led light strip

by Prof. Rickie Rau DVM Published 3 years ago Updated 2 years ago
image

How to Fix an LED Light Strip

  • Determine the area of damage
  • Unplug the light strip
  • Detach adhered lights with blade if possible
  • Use scissors along the copper markings to cut out the damaged section
  • Cut a new section of same light strip from a new or leftover roll
  • Attach back-to-back pin connectors to each section of light strip
  • Be sure to use the proper number of connector...

How to Fix an LED Light Strip
  1. Determine the area of damage.
  2. Unplug the light strip.
  3. Detach adhered lights with blade if possible.
  4. Use scissors along the copper markings to cut out the damaged section.
  5. Cut a new section of same light strip from a new or leftover roll.
Nov 7, 2021

Full Answer

How to fix broken LED strip lights?

  • First of all, please disconnect your power source for safety.
  • Then, you need to unplug the dimming cord from both the power supply and the LED strip light.
  • Next, plug the power supply and LED strip back into the receiver unit and reconnect the power supply to power.

More items...

Why are my LED lights not working?

  • Single LEDs remain dark? – No problem due to parallel connection
  • LED strip remains dark? – Check connection between controller and Stripe
  • Power supply defective? – Use another power supply with the same voltage for testing
  • Controller defective? – Repair not possible for user/not worthwhile from a cost point of view

How to troubleshoot your LED lighting system?

Method 2 Method 2 of 2: Testing with a Coin Cell Battery

  1. Use a coin cell battery to test your LED without burning it out. ...
  2. Purchase a corresponding coin cell battery holder with leads. Buy one that is made to hold the type of coin cell battery (e.g., a CR2025) you'll be testing with.
  3. Connect the black lead to the cathode and the red lead to the anode. ...
  4. Wait for the LED to light up. ...

How to reset LED strip?

With that in mind, here are the general steps for doing a factory reset in your LED strip:

  • Start by plugging in your strips before turning them on for several seconds. ...
  • At this stage, you should press the power button and hold it down for some seconds before connecting the power supply again
  • Hold the button down for approximately five seconds until the LED strips turn on. ...

More items...

image

How do you fix a ripped LED light?

2:004:29How do I repair my damaged LED strip lights? Push connectors repairYouTubeStart of suggested clipEnd of suggested clipEither side of the section. So that I know which section is the offending section to cut it out youMoreEither side of the section. So that I know which section is the offending section to cut it out you could also mark it with masking tape so that you are aware when the power goes out.

Why LED strip is not working?

Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. These tiny connectors are rather delicate items so you have to be very careful when inserting them.

Why is only half of my LED strip lights working?

But the answer is simply that one colour of the RGB/W LEDs is not working within that section and needs replacing. This can be caused by static-electricity damage, or bending and twisting the strip too much, or being trod on, damaged in transit, a cheap poor-quality strip, or dry solder joints.

How do you make LED strips work again?

1:055:26Light Strips Falling Down? Best Solution - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can do to hang them back. Up. The first is really simple. And that's to use rubbing alcohol toMoreYou can do to hang them back. Up. The first is really simple. And that's to use rubbing alcohol to clean the surface before installing.

Can LED lights be repaired?

A great benefit to LED bulbs is you can repair almost everything. Premature burnouts can be caused by poor component quality, LED overheating, and voltage jumps. The good news is that you don't have to have a lot of experience to handle the repair and the cost is significantly less than the price of a new bulb.

Do LED lights strips burn out?

Do LED Light Strips Burn Out. LED light strips fade over time. So unlike a regular incandescent light, LED lights don't burn out. Over the span of years you might notice your LED light strip fading.

How do you fix half LED lights?

0:224:50How To Fix Christmas Lights Half Out - Ace Hardware - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you take a screwdriver or utility knife when you open this up you'll expose the two fuses thatMoreIf you take a screwdriver or utility knife when you open this up you'll expose the two fuses that are there and you can see that if half the lights are out it could be that one of those fuses.

Why is a section of my LED lights out?

If one of your LED light strands isn't working, it's probably just because it has a bad bulb. If one bulb dies, it can cause the rest of the strand to stop working. The only way to fix the problem is to find the bad bulb. Sometimes only a section of the lights will go out, making your job pretty easy.

How do you fix ripped LED strips without soldering?

How to use a Tape to Tape connector This is the Tape to Tape connector for single colour LED Tape. ... Cut the LED Tape along the cut line with a pair of scissors. ... Now take your Tape to Tape connector and your 2 pieces of LED Tape that you are looking to join. Open the connector.More items...•

Can you reconnect LED Strip Lights?

A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.

Why are half of my LED lights dim?

Voltage drop comes into play when your LED strip runs, your wiring, or both, are too long. The resistance in these conductors adds up - and your LEDs start to operate below their optimal voltage range, resulting in dimming.

How long do LED light strips last?

50,000 hoursLongevity. LEDs have an unbelievably long expected life-span, compared to both incandescent and fluorescent lights. With an average life-expectancy of some 50,000 hours, LED strip lights will still be burning bright in 17 years' time, long after their traditional counterparts will have expired.

Why isn't my LED light strip turning on?

A majority of the time a loose connection is often the cause of an LED light strip not turning on.

What to do if your lights are beyond repair?

If your light strips are beyond repair, it might be time to upgrade your lights.

Why do light strips fail?

And bending or crimping light strips around corners without proper connections is also a major cause of light strip failure.

What is the pin used to connect strip lights?

Using plastic back to back connector pins is what you’ll need to connect two sections of strip lights together. The small pin connectors simple allow for the electrical current to move through the affected area with no interference.

What happens if your lights are completely out?

If your lights are completely out, then the power source could be an issue. Sometimes using a wall switch to control an outlet is used, so make sure the wall switch is turned on.

How often do you cut copper on a light strip?

You can cut on the copper markings that are usually every 1 or 2 inches throughout the light strip roll. You’ll need to leave a bit of copper to allow for a connection point to the new section of light.

What is an L shape connector?

L-Shape connectors make it easy to connect multiple sections at a 90 degree corner. For 3528/5050 SMD RGB.

Step 1: Before You Start

Before doing anything, wear protective gloves and eyewear to prevent injury. Then, unplug the light strip from any outlets and leave it unconnected. When you are ready to begin, you will want to ensure that the circuit breaker has been turned off for safety purposes.

Step 2: Determine the source of the problem

After you have turned off the power, please pick up your new LED strip light and inspect it for damage. Most LEDs are enclosed in a transparent plastic shell glued to the back of the circuit board. If there are any visible damage – cracks or loose pieces of plastic – return both components for either an exchange or full refund.

Step 3: Fix Broken Strip Lights

If you plugged in your LED strip lights and one or more strips remained unlit, the issue is most likely an open circuit. This means there is no electrical current passing through that specific LED for some reason, causing it to remain dormant. To fix this problem, follow these steps:

Step 4: Connect Strips Together

When repairing broken sections of LED strip lights, it is essential to keep track of which LEDs connect in series vs. in parallel, not to create a short circuit when you reassemble the strips. Each set of these LEDs needs to be connected by being soldered in series or inserted into plug-and-play wire nuts or crimp caps.

Step 5: Fix a String of Strip Lights That Are Only Connected in One Spot

You should check all the connections before you start but assuming no other fixing issues are going on, it may simply be that your LED strip lights have been plugged into the wrong plug altogether – that is, if one of them does not turn on when the rest do.

Step 6: Use Color Filters

Using color filters with your LED strip lights requires you to do just that: apply color filters or gels onto each individual LED within its designated area for effect. This can be useful to create an atmosphere, whether it be soft moonlight in the background or footlights under a buffet table.

Step 7: Fix Led Strip Lights With Broken Segments

Broken pieces of your broken LED strip lights are usually caused by accidentally stepping on, cutting, or yanking them away from where they were initially placed, no matter how careful you were.

What to do if a led strip is not working?

So the first thing you should do when troubleshooting a non-working led strip is to check if all of the solder joints are still intact and connected well. Check for cold solder joints or places where copper doesn’t look bright and shiny.

What happens if you break an LED strip?

Have you ever had a broken LED strip? A common issue with led strips is that they will stop working, or the lights will go out. This article will show the steps on how to fix a broken led strip.

How to fix a torn silicone tube?

Cut another length of the flexible, waterproof silicone tube and stick it on top of the area that is torn apart. Then, seal it with a soldering iron.

Why does my circuit short out?

In addition, due to excess friction and heat, a small scratch or dent in the insulation will short out the circuit.

Can a led strip be bent?

In addition, Over-bending and deforming can turn a working led strip into one that doesn’t light up.

Can you cut a heat shrink tube over electrical tape?

Once you have confirmed that everything is working, now you can cut out a piece of heat shrink tube big enough to slide over the electrical tape on both sides.

Can you use waterproof adhesive on LED lights?

Make sure that you are using a waterproof type of adhesive so that when the weather changes, your LED light strip will still be in good shape and continue working!

What is an LED strip light?

Usually, you will find a LED strip on the shelf in the form of a long roll. At first sight, it looks like a strip on which someone welded light diodes, one after another.

What to do if you find a resistor on a flexible strip light?

If you find a damaged resistor, you can either try to repair it or call the customer support. Indeed, flexible strip lights should not have this problem. If you do not find a damaged resistor, find the four wires that control the three primary colors. The fourth one is for voltage.

What does RGB stand for in LED lights?

Multi-colored LED diodes create multicolor light in a new way. In short, the RGB acronym stands for Red, Green, Blue. This color model is responsible for the different luminous combinations.

What to do if you can't shut the lids on a RGB strip?

If you cannot shut the lids, go back and reinstall the strip in place, gently . After all this, you are ready to lit your strip for a test. As you might expect, varying connectors are available for RGB, RGB W, simple color, and tunable white strips. Basically, their different appearance does not matter.

Why does LED light flicker?

LED strip lighting works accordingly to the principles of LED lights. In detail, the visible flicker appears because of the standard wave patterns. More precisely, luminous wave patterns from AC powered lighting sources. Sometimes, you could notice a visible flickering with your own eyes.

How long do LED lights last?

High luminous efficacy goes hand in hand with the life span of the LED diodes. A Multicolor LED light strip can last anywhere from days up to years. In part, its use affects the luminous efficiency. That is, how bright your LEDs are.

How many colors does an LED strip display?

Now, the LED strip only display one color. No matter what you tried, nothing seems to fix the problem.

image

Things You’Ll Need

A Stepwise Guide on How to Fix Broken Led Light Strips

Step 2: Check The Strip and Repair

Tip

Warnings

Precautions

Frequently Asked Question

  • Can LED Strip Light Be Repaired?
    Yes, new LED bulbs make it possible to repair practically everything. All you have to do now is identify the issue and take appropriate steps to repair or replace any damaged parts of the LED bulb so that your light can operate effectively once more.
  • How Do You Fix LED Strips That Won’t Turn On?
    Look for any noticeable faulty wiring, and double-check that all of your connectors and cables are in place and haven’t come loose. Tighten DC adapter screws and re-insert LED strips into solderless connections, as these are common contact failure spots.
See more on lighthax.com

Conclusion

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9