How do you take apart a Molex connector?
To disconnect a Molex connector (male and female connection), simple press down on outside clip and pull the connectors apart. The power connectors have hooks that allow the connectors to latch into the connector housing. Once the crimped wire has been inserted into the housing, it will be difficult to remove.
Can you reuse a Molex connector?
3:284:34Remove Pins From Amphenol / Molex Connectors For Reuse (4K)YouTubeStart of suggested clipEnd of suggested clipPull it out of the connector. Sometimes it takes a little bit of force but it's not much. And thenMorePull it out of the connector. Sometimes it takes a little bit of force but it's not much. And then again when you're ready to reuse it you expand the ears push it back in the plug.
How do you fix a broken connector pin?
0:217:06Vex : Fix Broken Motor or Sensor Connector pin - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis crimper it's the same crimper as this wrist right here okay. And it's the just a crimping toolMoreThis crimper it's the same crimper as this wrist right here okay. And it's the just a crimping tool for the two point five four millimeter pin.
How do I change my connectors pin?
0:396:01Connector Pin Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold down the connector. And basically these little rectangles are the part of the connector that'sMoreHold down the connector. And basically these little rectangles are the part of the connector that's holding the pins into place.
How do you crimp a Molex?
1:494:00011: MOLEX & OPEN BARREL PIN CRIMPING, Video 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd fits right in there the insulation just goes up to the tool itself you then crimp it. And youMoreAnd fits right in there the insulation just goes up to the tool itself you then crimp it. And you can see the wire is secured give it a little pull test make sure it's all tight.
Can you reuse crimp?
2:506:17Reusing Crimp Lugs (Updated Video Available) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat's it's not going to corrode on me okay back to it. I've now opened up both sides enough that I'MoreThat's it's not going to corrode on me okay back to it. I've now opened up both sides enough that I've gotten all the copper out of there pull it out one by one.
How do you fix a broken connector?
3:057:29How To Fix Broken Wiring Sensor / Connector Plug Clip To Make A ...YouTubeStart of suggested clipEnd of suggested clipI'm going to use the factory clip to show you is all we're trying to do is wedge a piece of plastic.MoreI'm going to use the factory clip to show you is all we're trying to do is wedge a piece of plastic. Like this very top piece between this wedge.
How do you solder a broken pin?
2:2012:16IC Pin Repair / How To Repair Broken Pins On IC - 2 Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm just gonna gently wick. Off just some remains of the solder that's. There. So the main thing isMoreI'm just gonna gently wick. Off just some remains of the solder that's. There. So the main thing is just take your time with this just gently ease off the damaged.
How do you solder connector pins?
0:006:07How to solder 20-16 AWG wire into multipin military connector - YouTubeYouTubeStart of suggested clipEnd of suggested clipWelcome to another american beauty product support video tutorial this application shows resistanceMoreWelcome to another american beauty product support video tutorial this application shows resistance soldering 16 gauge wires into a 17-pin amphenol style socket pin connector.
How do you Repin connectors?
0:321:56Repair and DePin/RePin Automotive Connector, Pigtail, Plug. Fog lamp ...YouTubeStart of suggested clipEnd of suggested clipAble to remove the pin there same thing on this side lift the catch. Up. Once you lift it up now youMoreAble to remove the pin there same thing on this side lift the catch. Up. Once you lift it up now you can remove the pin. Then if you're repainting the connector all you got to do take your pins.
How do I install Molex connector pins?
0:242:36Assembling a Molex Connector - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what we'll do is we will slide the wire. In until the wire is completely centered in in theMoreAnd what we'll do is we will slide the wire. In until the wire is completely centered in in the first set of tabs. Compress it down and that will seal it up sometimes just give it a light slug tug.
What does a Molex connector look like?
In such a connector, cylindrical spring-metal pins fit into cylindrical spring-metal sockets. The pins and sockets are held in a rectangular matrix in a nylon shell. The connector typically has 2 to 24 contacts and is polarized or keyed to ensure correct orientation.
Can you reuse push in connectors?
Connector is reusable on solid wires of the same wire gage or larger. If reusing connector, cut and re-strip conductors.
How do you reuse electrical connectors?
0:161:12How to reuse WAGO Connectors / Remove wires SUPER EASYYouTubeStart of suggested clipEnd of suggested clipIt's not always easy grab a hold of it start twisting the wire twist. And pull twist and pull BAMMoreIt's not always easy grab a hold of it start twisting the wire twist. And pull twist and pull BAM you take the wire back out just in case you made a wiring mistake.
Can you reuse electrical pins?
0:162:28Wire Pin Reuse - YouTubeYouTubeStart of suggested clipEnd of suggested clipI did that to get the actual wire jackie holder i just shoved this needle in the tops. Pried themMoreI did that to get the actual wire jackie holder i just shoved this needle in the tops. Pried them apart a little bit each time eventually i got it wide enough that i could slip over the end.
How do you remove wires from a push in connector?
0:252:40IDEAL In-Sure Push-In Wire Connectors HOW TO REMOVE WIREYouTubeStart of suggested clipEnd of suggested clipPull away from the connector and will go back and forth and it will come out again make sure theMorePull away from the connector and will go back and forth and it will come out again make sure the power is off I'm going to attempt to do. This I've got it on the tripod.
Why add Molex connectors to wires?
Adding connectors to wires helps with connectivity and allows for plug and play compatibility with electronic and electrical devices. This guide will provide an overview of adding and removing Molex connectors and housing to wires and the how-to process of doing so.
Can crimped wires be fed into connector housing?
The crimped wires can now be fed into the connector housing. The orientation of the wires can be based strictly off preference or may be required to follow a certain pin layout, depending on the type of system that you are working with.
Can you remove crimped wire from a power connector?
The power connectors have hooks that allow the connectors to latch into the connector housing. Once the crimped wire has been inserted into the housing, it will be difficult to remove. However, there is a method of removing the wire from the housing without damaging the power connector.
Can you remove wires without damaging the connectors?
Removing the wires without damaging the connectors is a simple method of enabling users to switch the polarity of actuator wires without having the need to obtain additional Molex connectors or Molex Housing.
How to reinstall Molex connector?
Push the wire into the correct slot on the connector to reinstall it. Once you’ve replaced the connector pins, slide the pin into the Molex connector slot until it clicks into place. Give a light tug to make sure it’s attached. Make sure you install the wires in the same order they were in when you removed them.
What is Molex connector?
Molex is a company that manufactures a variety of different types of electrical connectors that are used for applications such as computers and electronic devices.
How to connect a wire to a connector pin?
2. Slide the end of the wire into connector pin. Take your wire and push the end of it into the connector pin being held by the crimper. Push the wire into the pin until the end of the wire is even with the end of the pin. Don’t push the wire so far that it’s sticking out of the other side of the connector pin.
How to remove a connector pin?
Cut off the old connector pin with wire cutters. Take a pair of wire cutters or scissors and locate the base of the connector pin on the end of the wire. Make a clean cut through the base of the connector pin to separate it, and then dispose of it in the garbage.
How to replace pins on multiple wires?
If you plan to replace the connector pins on multiple wires, push down on the pins individually and slide them out of the connector. Use your wire cutters to snip off the connector pin from the end of the wires. Keep the wires in order so they’re easier to reinstall into a new connector.
How to use Molex extraction tool?
If you have a Molex extraction tool, use it to press down on 1 of the pins through the small slot. If you don’t have an extraction tool, use a small flathead screwdriver. Press down on the pin gently to avoid damaging it so you’re able to reuse the connector.
How to remove a pin from a wire?
Pull on the wire connected to the pin to remove it. While you’re holding down the pin with 1 hand, use your other hand to take hold of the wire connected to the pin. Gently tug on the wire to separate it from the pin. Slide the wire all of the way out of the connector.
