HOW TO FIX A SEAT BELT RETRACTOR? 5 EASY STEPS.
- 1. TAKE OFF THE TRIM PANEL. Before you start fixing, a safety precaution: Take off the minus battery terminal on the car. This is to avoid accidental ...
- 2. CHECK THAT THE SEAT BELT RETRACTOR IS THE ACTUAL PROBLEM.
- 3. RETRACT THE SEAT BELT AS MUCH AS POSSIBLE.
- 4. CLEAN THE AREA AROUND THE SEAT BELT RETRACTOR.
- 5. APPLY WD-40 OR A SILICONE BASED SPRAY TO THE SEAT BELT RETRACTOR.
How do you fix a retractable seat belt?
Possible Problems
- Defective seat belt retractor. The seat belt retractor may be broken and needs to be replaced. ...
- Twisted seat bel. You may have to remove the plastic trim to check and make sure that the seat belt is not twisted. ...
- Previous accident. ...
- Seat belt age. ...
- Bad Retractor Spring. ...
How to fix a retractable seat belt?
Here’s the procedure:
- Take the proper wrench and take the belt loop of. A screw is often hidden under a small plastic covering on the loop itself.
- Take the trim tools and take off the trim. Be careful and take your time as this is a tricky job. ...
- After the trim is off, you’ll see the retracting mechanism. ...
How to fix locked seat belt after accident?
Your seat belt pretensioner may need repair if:
- The seat belt is too tight or too loose.
- The seat belt won’t retract after releasing.
- The seat belt doesn’t stay taut.
- The seat belt won’t lock or unlock.
- The seat belt stays locked.
How do you open a seat belt receiver to repair?
Method 2 Method 2 of 2: Removing and Reinstalling the Front Seat Download Article
- Slide the seat as far forward as it can go. ...
- Take out the seat belt anchorage point with a socket wrench. Seat belt anchorages are often hidden behind a piece of trim.
- Remove the bolts at the back of the sliding rails and tip the seat forward. ...
- Reconnect the electrical wires to begin reinstalling the seat. ...
Can seat belt retractors be fixed?
Seat belts are such an important part of our driving, but we rarely give them much thought. Luckily, you can fix your car's seat belt retractor by doing some at-home troubleshooting before taking the car to a shop.
How do you fix a retractable seat belt?
0:382:05Seat Belt Won't Retract Easy Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake as much of the seat belt as you can and just place it in the water. After. It's been soakingMoreTake as much of the seat belt as you can and just place it in the water. After. It's been soaking for about 10 or 15 minutes come back and squeeze it.
What causes a seatbelt not to retract?
If the seat belt in your car isn't retracting, there are two probable causes: the belt is twisted, or the retractor is malfunctioning. You'll be able to fix the belt yourself, but you'll need to replace the retractor if it's malfunctioning.
How much does it cost to fix a seat belt retractor?
The replacement cost of a seat belt pretensioner is around $150 to $200. The cost of the parts is about $50 to $100 while the cost of the labor is about $100 to $125. You may be able to reduce the labor if you can find a cheap enough mechanic in your area or simply enlist the help of a buddy that likes to work on cars.
How does a seat belt retractor work?
2:007:41Seatbelt | How does it work? - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis movement will move the hinge and trigger a locking mechanism. This locking will prevent anyMoreThis movement will move the hinge and trigger a locking mechanism. This locking will prevent any further release of the webbing from the retractor.
Can you replace a seat belt yourself?
Replacing your seat belt it quite a simple job, but it does require a modicum of mechanical knowledge to get it right. There are two parts to the modern seat belt – the buckle and the strap and the retractor unit.
How do I know if my seat belt tensioner is bad?
3:404:36Airbag Systems How to Test a Seatbelt Pre-Tensioner - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf I touch them both together there's your short that's how it should have read this one's readingMoreIf I touch them both together there's your short that's how it should have read this one's reading open already so it's ready to plug in and go that's the signal you're looking for where's 2.2.
How do I get my seat belt unstuck?
0:3810:20Seat Belt Stuck, NOT RELEASING Easy Fix- Watch the video - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know just a couple basic tools a punch a little you know paw or screwdriver the client.MoreYou know just a couple basic tools a punch a little you know paw or screwdriver the client.
How do you manually release a seatbelt?
0:161:33How to Release a Car Seat Belt From the Retractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have to release it slightly. And then pull it gently and it'll come out some seat belt stopMoreYou have to release it slightly. And then pull it gently and it'll come out some seat belt stop pawls become stuck so even if you're pulling gently.
Is a slow retracting seat belt an MOT failure?
as long as they're 'effective' when you are seated in the car, and the belt/buckle are in good physical condition (no excessive fraying/cuts) then they shouldn't be a reason for an mot failure. I know it's different, but a racing harness is manually adjusted and doesn't retract - and as far as I know, these are fine.
How do you unstick a seatbelt?
Unlocking the seat belt retractor.Slowly allow the belt to reel back into the retractor at least one-half inch.Once the belt has retracted, slowly pull it out. This should override the retractor spool lock mechanism.You may need several attempts to unlock the seat belt.
Why won't my seat belt retractor work?
However, if you’ve learned how to fix a seat belt retractor and it still doesn’t work, then there’s a good chance that the retractor itself is faulty. It’s not that common but it does happen.
Where is the seat belt retractor located?
Once you take off the panel, you’ll see the seat belt retractor. It’s in the lower part of the B pillar. This is a good time to check and be sure that the retractor is the actual problem. After all, if you want to learn how to fix a seat belt retractor, you have to know that it’s causing the problem not anything else.
Why is it important to repair a broken car?
A very important part regarding safety so its proper functioning is necessary. Having this in mind the repair should be done as soon as possible.
Can you repair a retractors?
I’ve seen people open up and repair retractors (very successfully) but nothing beats a new or good used one.
Can you force a panel to break?
Using force, ripping panels off, breaking clips and holders, or even breaking the whole panel will result in having to buy a new one or having to return the old one however you can.
Can a screwdriver damage a seat belt?
Using a screwdriver or any kind of metal tool will damage the trim panel for sure or leave nasty scratches and bents. Besides this, you might need a ratchet and matching sockets for additional dismantling (like taking off parts of the seat belt assembly, various holders, or else). Prior knowledge.
Prior Experience
If you’ve never removed this trim panel before, Google how to do it for your specific vehicle. It’s also good to contact a specialist or consult a manual. Otherwise, you’ll most likely break a plastic clip or something, resulting in the panel swaying or rattling when you return it. It could even fall off at some point.
Patience
Patience is essential if you want to learn how to fix a car seat belt retractor. Getting agitated when removing the trim panels will certainly result in damage.
Verify That the Problem Is With The Seat Belt Retractor
The seat belt retractor is visible after the panel is removed. It’s towards the bottom of the B pillar.
Retract the Seat Belt As Much As Possible
Pull the seat belt as far as it will go, and the spot where the fabric is linked to the metal spool will be visible at the end.
Spray The Seat Belt Retractor With Wd-40 Or A Silicone Based Spray
Ensure to clean the area where you will do a seat belt replacement, then lubricate the retractor.
Conclusion
Replacing the trim panel and rubber door seal is the next step. If you’ve learned how to perform seat belt repairs and it still doesn’t function, the retractor may be defective. If you want to save time and effort, consult with a seat belt repair specialist.
Step One: Disconnect the Trim Panel
Before you begin, take the negative battery terminal off the battery to keep the explosive charge on the seat belt retractor from accidentally igniting! While working, you may unintentionally disconnect or damage the electrical connector, so use caution.
Step Two: Check to See If the Retractor Is Broken
Remove the panel to reveal the seat belt retractor. It can be found in the B pillar.
Step Three: Retract the Seat Belt
Tighten the seat belt all the way. With the metal spool to cloth endpoint, it may now be able to retract more readily. A gentle pinch around the seat belt loop will suffice in this circumstance.
Step Four: Remove Dust and Debris
The retractor could be covered in dust and filth that looks like wool. It should be cleaned up with a vacuum or compressed air. Cleaning the seat belt retractor usually improves its function. In many cases, grime obstructs the mechanism's operation. Therefore, cleaning it is useful.
Step Five: Wrap a Silicone Spray or WD-40 into the Seat Belt Retractor
After cleaning, lubricate the retractor with a WD-40 spray or a silicone-based spray. Spray the retractor's plastic part between the rotating metal spool and the retractor's metal spool with the retractor's metal spool. Instead of flooding it, use brief bursts. If this was the case, the matter should be resolved as soon as possible.
Conclusion
While repairing a seat belt retractor is doable, it’s not that easy, and you may feel frustrated if you can’t fix it yourself. The best course of action is still to bring your seat belts to the experts. They know exactly what to do, saving you the time and effort you could have spent elsewhere.
