What should I do if my sprinkler valve is stuck?
Shut off the sprinkler system controller before beginning any repair so it can not initiate a watering program. Before disassembling the sprinkler head to get at the valve, turn off the water supply. You can be injured if you try to release the valve while it is under water pressure.
When should I replace my automatic garden sprinkler system?
If yours is an automatic garden sprinkler system and its valve diaphragm is worn out, you should replace it. So if you notice that it’s damaged and if it continuously failing to stop the flow of water, you can follow these tips on how to replace the valve. Check sprinkler heads and find those that do not shoot water properly.
What do you need to know before repairing a sprinkler system?
Here’s what you need to know before attempting any sprinkler repair: The sprinkler controller turns the water on and off, usually located in a small box near your yard’s water meter. They connect to the pipe from the home’s plumbing system and control the output water flow.
How do I fix low water pressure in my sprinkler system?
If you're experiencing low water pressure, check the sprinkler system valves on the backflow device to make sure they're open. Turn the valve on the horizontal pipe first, then the vertical pipe valve.
How do I troubleshoot my sprinkler system?
0:464:30Troubleshooting an Irrigation Zone that Won't Activate - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can check for water pressure either by operating the zone valve manually or opening a waterMoreYou can check for water pressure either by operating the zone valve manually or opening a water outlet on the main line next check that there is power to the irrigation.
Why is one section of my sprinkler system not working?
If only one zone isn't working, the field wire is damaged. If none of the zones in a control valve box is working, the common wire is damaged, although the field wires could also be bad.
How do you fix a broken sprinkler tee?
0:326:23How To Repair PVC Sprinkler Pipe; Glueless Tee & Slide ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what we are going to do today is replace this tee using PVC lock fittings you can see that thisMoreSo what we are going to do today is replace this tee using PVC lock fittings you can see that this was a glued in tee. And we're going to replace this glued in tee with a PVC lock no glue tee.
Why is my sprinkler head not working?
Clogged sprinkler heads: You may have a clogged sprinkler head if the head doesn't rise and there is no water. Dirt, sand and other debris build up in the sprinkler head filters. To clean a filter: Turn off your water, lift the pop up riser, remove the nozzle and the filter, clean the filter and return to the nozzle.
How do you know if a sprinkler solenoid is bad?
Signs You Have a ProblemThe Water Won't Shut Off. If you have this problem, it's very likely the solenoid. ... Low or Uneven Water Pressure. The solenoid controls the water pressure. ... Water Leaks. There are many points in a sprinkler system that can leak. ... Current Testing. ... Valve Inspection. ... Parts Replacement.
How do I find a short in my sprinkler system?
0:463:39Using an Ohmmeter to Troubleshoot a Sprinkler System - YouTubeYouTubeStart of suggested clipEnd of suggested clipLess than 20 it's got to be less than 10. If it's less than 10 ohms what's happening is that theMoreLess than 20 it's got to be less than 10. If it's less than 10 ohms what's happening is that the signals not making its way through the entire coil.
How do you replace a sprinkler head connector?
1:586:03Sprinkler Head Broken Off How To Reset Replace Stripped ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSet again the taper tool makes that much easier where you don't need the socket. On it so you couldMoreSet again the taper tool makes that much easier where you don't need the socket. On it so you could actually split off these risers. And use them in different places.
How do you replace a sprinkler elbow?
0:574:52How To Repair a Sprinkler PVC Pipe; Pushfit Elbow Fittings PVC-LockYouTubeStart of suggested clipEnd of suggested clipThe first step that I'll do is remove.MoreThe first step that I'll do is remove.
How do you fix a leak in a PVC T joint?
Epoxy. Repair epoxy is putty or viscous liquid that can be used to repair pipe leaks on PVC and its joints. To repair your pipe or joint using epoxy, first clean and dry the damaged area, ensuring water can't reach the affected area. If necessary, mix the putty or liquid according to the manufacturer's directions.
How do you fix a sprinkler head that doesn't spray?
1:172:12Water Wise - Fix A Clogged Sprinkler Head - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround the filter or inside of it and the hole where the water comes out of on the nozzle is clearMoreAround the filter or inside of it and the hole where the water comes out of on the nozzle is clear of any debris.
Why does one of my sprinkler zones have no pressure?
Often when your sprinkler system was running fine, and then one zone began to lose water pressure, the culprit is a leak in the zone's lines or a leak at a nozzle or two. Leaking nozzles won't produce the same water pressure and need to be replaced, which is fairly simple.
Why is my sprinkler system stuck on one zone?
If your sprinkler system isn't working in all zones, chances are the problem is localized to the one or two zones that aren't working. Each zone has its own valve, so that's a good place to look. Head out to each valve and see if it is opened fully, broken, rusted, or stuck. Turn valves to the left to open them more.
How do you unclog a sprinkler pipe?
0:092:41How to Fix Clogged Heads on your Sprinkler System - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically what you'll do is hold the cylinder of the irrigation. Head with your hand to keep it fromMoreBasically what you'll do is hold the cylinder of the irrigation. Head with your hand to keep it from retracting back into the body of the head. You'll then take off the nozzle.
What causes low water pressure in one station of a sprinkler system?
If the pressure is low at only one or two sprinkler heads, they may simply be dirty. Examine the sprinkler head and filter and clean if needed. Grass can also grow around the base of the sprinkler heads and cause them not to pop up fully, so trim and clear away any obstructions.
How to adjust sprinkler heads?
Sprinkler heads often need to be adjusted if the water isn't reaching all parts of your lawn. Move the sprinkler heads around and try changing the...
How to extend a broken underground sprinkler line?
If you can't use a pipe cutter or don't have an extra section of PVC, you can use a hacksaw to extend the line. Cut two pieces of PVC that are each...
How to install a sprinkler system?
- Locate the area where you want to install the sprinkler system. It's best to install it in an open space, like a lawn or garden. - Mark the spot...
How to winterize a sprinkler system?
If you're interested in blowing out your sprinkler system to prevent water from freezing inside the pipes during wintertime, here's what you need t...
How to replace a sprinkler head?
You can change a sprinkler head by using a wrench or screwdriver. First, make sure to disable the water supply to the sprinkler system and drain th...
How much does a sprinkler system cost?
A sprinkler system typically costs between $300 and $3,000, depending on the size and complexity of the system. However, some homeowners choose to...
How to drain a sprinkler system?
To prevent standing water from damaging your lawn or garden, drain the sprinkler system before you start digging. You can easily do this by turning...
How to cap a sprinkler head?
You can use an adjustable wrench to cap a sprinkler head by gripping the head and turning it counterclockwise until it is completely unthreaded. Th...
How to design a sprinkler system?
Designing a sprinkler system typically involves using an online design tool or buying a guide that you can follow step-by-step. After determining t...
How often should I water my lawn?
You should water your lawn every day to keep it healthy. If you live in an area that sees a lot of sun or wind, water the lawn more frequently. But...
How to avoid sprinkler problems?
Avoid this problem by understanding each sprinkler’s precipitation rate and using only those with similar pressure ratings on the same zone for efficient water in all garden areas.
What happens if the sprinkler zone stops working?
If the zone stopped working, there might be an issue in the voltage. Know that the water system is divided into zones; each has its valve controlling a sprinkler head.
Why is my water sprinkler controller not working?
The water sprinkler controller stops working. One of the problems can be on the controller not switching to the manual mode. When it does happen, it means that there is no power to the controller. To fix it, check that the controller is wired properly based on the system’s Electrical Circuit and Connection diagram.
How to tell if a sprinkler valve is open?
You can tell that the valve is open once the handle is parallel with the pipe. (The backflow device is above ground and its valve 12 inches above the highest point of the yard’s sprinkler head. Many of these devices have a valve on both the vertical and horizontal pipes.)
Why does my sprinkler head not pop up?
And in some cases, the heads do not pop up. It is another common problem of a sprinkler system. Low water pressure. One of the things to do is to inspect the backflow device’s valves to see if they’re open. Make sure to turn on the horizontal pipe’s valve before switching on the vertical pipe valve.
Why does my zone valve leak?
Zone valve leaks. This problem can be caused by some issues. For one, it can be due to a damaged or torn diaphragm inside the valve. To fix the problem, you can just disassemble and then rebuild the valve with a new diaphragm. If the cracked body of the valve is causing the leaks, you can replace the zone valve.
How to fix a water nozzle?
To fix it, you can turn the system off and then take the nozzle out. Be sure to clean all the debris from the screen of the nozzle. Water not spraying out the nozzle. In order to remove the nozzle, pull its stem out its body using one hand while gripping the nozzle with another hand.
How to repair a tree line that has roots?
If the line was damaged by tree roots, reroute the line by digging a new trench away from the tree.
How to fix a defective solenoid?
Disconnect the wires and unscrew the defective solenoid from the control valve. Insert a new one and turn it until it's finger-tight.
How to tighten a pipe clamp?
Place a clamp on one of the line ends, insert a slip coupling, then tighten the clamp. Place a clamp on the second pipe end, expand the coupling while inserting the nipple into the pipe, then tighten the clamp. Step 5.
What happens if your watering system is not turning on?
Your watering system is divided into a series of zones. Generally, if you have a zone that's not turning on, you have an electrical problem. Make sure the zone wires are firmly attached to the terminals in the controller, the transformer is plugged in, and the circuit breaker at the main panel is on.
What is the phone number to access underground water lines?
Caution: Before you start digging to access the underground water lines, electrical wires or spray heads, dial 811 to have your underground utility lines identified and marked.
How to clean a syringe head?
Remove the screen basket from the bottom of the head, then clean it with water.
Which way to turn a valve?
Turn the valve on the horizontal pipe first, then the vertical pipe valve.
How to release a sprinkler valve?
Release the sprinkler valve solenoid—a thin cylinder with a wire protruding from each end—from the sprinkler head by unscrewing it in a clockwise direction. A plunger is located near the solenoid. Check that the plunger can release and retract freely.
How to release tension from a diaphragm?
Squeeze the spring gently between your fingers and release it: it should release the tension instantly. Rinse off the diaphragm with fresh water to remove any particles or debris. If either the diaphragm or spring is damaged, replace them with new parts.
Can you run over a sprinkler valve?
Your lawn watering system is only effective if every sprinkler valve is working properly. Sprinkler valves can suffer damage when you run over the sprinkler heads with your mower or lash them with the weed slicer. Here are tips on repairing sprinkler valves to prevent future problems.
