How to fix a lawnmower pull cord that is stuck, step by step
- To start, inspect your blade for any stuck strands of grass or debris. Remove them as they cause the pull cord to get stuck.
- Open the blower housing and inspect the recoil starter. If it appears damaged, you need to replace it.
- Check if the engine is hydro-locked, remove the spark plug and pull the rope repeatedly to restart the engine.
Full Answer
How to fix pull string on lawn mower?
How to fix a lawnmower pull cord that is stuck, step by step: Step 1: To start, inspect your blade for any stuck strands of grass or debris. Remove them as they cause the pull cord to get stuck. Step 2: Open the blower housing and inspect the recoil starter. If it appears damaged, you need to replace it.
How to replace a lawnmower pull cord?
Replacing a lawnmower pull cord, step-by-step:
- Gather the tools and correct replacement cord. Before we can remove the pull cord, you need to ensure that you have the equipment and materials required for the ...
- Unscrew the starter setup. The pull cord is attached to the lawnmower’s starter disk. ...
- Remove the pull rope. ...
- Replace the old pull string with the new one. ...
How to fix mower starter rope Briggs lawnmower pull cord?
Tie a Knot
- Put the handle on the rope and tie a knot. ...
- If the rope on your lawn mower extends up the handle, make sure to place the rope handle in its final position before tensioning the rope slightly and tying the ...
- Let the pulley wind the rope back into the rewind.
- Reinstall the rewind unit and any other parts you've removed.
Should I repair or replace my lawn mower?
How to Know When It's Time to Replace Your Lawn Mower
- Cover your bases... This should always be your approach, Kiser says; he recommends checking and replacing the air filter, oil, and gasoline before jumping to any conclusions.
- Don't let gasoline sit in the machine. ...
- Replace dull blades. ...
- Check the belt. ...
- Consider the bottom line. ...
How do you fix a broken lawn mower pull cord?
2:264:31How to Replace a Pull String on a Push Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then place the knot in the pocket on the starter pulley. Now I'm going to hold the rope andMoreAnd then place the knot in the pocket on the starter pulley. Now I'm going to hold the rope and remove the screwdriver. And slowly allow the rope to coil back into the pulley.
How do you reattach a pull cord?
1:583:54How to Replace the Pull Cord on a Small Engine by @Gettin' Junk DoneYouTubeStart of suggested clipEnd of suggested clipBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keepMoreBut I've already replaced it you're gonna take this and spin it by hand against the spring. You keep spinning it over and over. Until you get to the point where you have a lot of tension.
How do you fix a pull cord that won't go back in?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
How do you fix a pull cord on a lawn mower that won't retract?
1:422:5510 second fix! Lawn mower pull cord not going back in recoil ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI just quite simply lifted up the lawnmower. Spun the blade backwards.MoreI just quite simply lifted up the lawnmower. Spun the blade backwards.
How do you start a lawnmower without a cord?
0:001:02How to start a mower without a pull start - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround. This circular piece in and the flywheel is and just keep wrapping it. Make sure to keep itMoreAround. This circular piece in and the flywheel is and just keep wrapping it. Make sure to keep it tight and then wrap it to where you have enough cord to start pulling.
How do you fix a Briggs and Stratton pull cord?
0:007:31HOW TO Repair The Pull Cord on Your Lawnmower With Briggs ...YouTubeStart of suggested clipEnd of suggested clipBut if the rope wasn't broken and still attached to the recoil. Which you would want to do is loosenMoreBut if the rope wasn't broken and still attached to the recoil. Which you would want to do is loosen this nut here and slide the rope right through the crack.
How do you put a lawn mower cord back in?
3:005:35How to easily fix a lawnmower pull start cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'd have to take it back out again just wind it back up all the way and jam your screwdriver inMoreYou'd have to take it back out again just wind it back up all the way and jam your screwdriver in for the cord lined up undo your simple knot. Let it go back.
What does it mean when the lawn mower string won't pull?
What if the starter rope won't pull? The crankshaft is connected to the blade shaft on your recoil start walk behind lawn mower, so if the pull cord is stuck, it could be because something is blocking the movement of the blade. Disconnect the spark plug for safety, then take a look under the deck.
What causes lawn mower pull cord stuck?
Grass and Debris Is in the Way The blade is connected to the starter coil, so if the blade is unable to move, your pull cord will be stalled as well. If your pull cord moves slightly, it's likely that there are grass and debris that needs to be removed from the housing on the top of the motor.
How do I replace a frayed lawn mower cord?
You still need to remove the assembly from the mower, although it's possible to do it in place, I don't recommend it. (1) Cut the correct length of new cord, measure it against the old one. Don't remove the old cord yet.
Why is my lawnmower pull cord loose?
Lawnmower pull cord loose? A lawnmower pull cord is likely to become loose when the recoil spring loses its tension. Replacing the spring is the correct fix.
How to stop a pulley from retracting?
2 – Have sharp pliers and a flat screwdriver to hand. Pull the cord out all the way, secure the pulley, use a screwdriver to lock the spokes of the pulley, stops it retracting .
What does it mean when a pull cord doesn't retract?
A broken cord is obvious, a pull cord that doesn't retract is usually a broken recoil spring, and a pull cord that doesn't catch and turn the engine usually means worn pawls.
What causes a pull cord to be heavy?
Too Full – Too much oil or oil that’s too heavy will cause the pull cord to be heavy.
What to do if your pull cord is hard to pull?
If your pull cord is hard to pull (stiff), make sure the bail lever is held during the starting process. I know most of you are in no doubt about how to start your mower, but for anybody that's a little rusty check out "How to start a mower".
How to load up a recoil spring?
If you choose not to remove the pulley, you must load up the recoil spring by turning it anticlockwise three turns. Then lock the pulley with the screwdriver as per the above guide, while you feed in and knot the cord, fit handle and double knot. Remove your locking screwdriver, check operation and refit, your done.
How does a Pull Cord Function?
The cord on your lawnmower connects to a hub that in turn spins when you pull the pull cord. This will spin the lawnmower’s blades together with the crankshaft.
Why is my cord stuck?
A stuck cord with no movement may indicate a damaged cord , or that the cord is catch ing on a component within the housing: Perhaps it is tangling up. In a worst-case scenario, the recoil spring may simply be damaged meaning that you will need to replace it.
How to replace a spring on a starter?
Replace the spring with a new one. Wind the hub. Reinsert the pull cord through the holes in the cover and in the hub.
Why is my lawn mower jammed?
Another possibility is if by chance a debris skirt on the lawn mower is pushed inward and the blade of the mower jams against it . Check for this when looking at the blade underneath your mower.
Why does my lawn mower stop automatically?
Solution 1: Initially, I would check out the automatic brake on my lawnmower. Some manufacturers have their mowers automatically stop the engine for safety purposes.
What happens when a mower spins?
When these parts spin, their spinning establishes a magnetic electrical connection that fires your mower’s spark plug and the mower’s carburetor will send fuel into the chamber for combustion .
How to reset a recoil spring?
Remove the engine starter and look for any tangles along the cord. Try pulling out the cord and rewinding it very slowly, then reset the recoil spring if it is possible or replace it altogether if necessary.
How to change a pull cord?
Take the new pull cord. Place a knot on one end of the pull cord and enter the new cable in the same place as the old cord. Slowly rotate it in the right direction around the pulley and fasten the cord. Keep turning the pulley until you start to feel some resistance.
Why is my lawn mower pulling cord loose?
A lawnmower pull cord becomes loose when the recoil spring has lost its tension. To fix this issue, remove the pulling assembly and give it a couple of turns to tighten it. Replacing the spring would be even better.
How to tie a pull cord to a pulley?
After inserting the cord through the rewind housing hole, please give it a knot. Heat the cord with a lighter flame. Hold the cord tightly while you remove the screwdriver and let the pulley unwind slowly. The cord will wrap around the pulley as it unfolds. Make sure to pull the pull cord tightly before allowing it to go to its previous position.
What is inside a lawnmower pull cord housing?
The pull cord housing’s major components are a handle, a pulley, a starter pull rope, and a recoil spring. Now let us get into more detail.
Why is my pull cord not working?
Your pull cord might not be working correctly because of worn-out recoil housing or spring issues. If the recoil housing is worn out, you should replace it with a new set. You can solve spring issues by replacing the spring winding with more turns on the spring to increase its tension.
What happens if the pull cord is broken?
This is the case when the cord is broken or when the recoil spring is damaged, and it does not return properly to the housing. If the pull cord is damaged, it is probably also a good idea to replace it. The step-by-step procedure will help with this. It is also possible that the pull cord is stuck.
How to keep starter pulley from rotating?
Keep the pulley rotating until the recoil housing pores and the pulley’s pellets are in the same position. Align the hole in the recoil starter housing with the hole in the pulley. Insert the screwdriver through the holes. It will prevent the pulley from rotating in the opposite direction.
Where is the pull cord on a lawn mower stored?
The mower’s pull cord rope is stored in the pulley, as well as the recoil spring. The pulley will guide and feed the pull cord, in addition to storing it. Pulleys are usually made from plastic and this is a part that can crack.
Where is the recoil on a lawn mower?
The recoil operates the mower’s flywheel. The flywheel sits below the starter, closer to the mower, and near the crankshaft. Magnets sit on the outside of the flywheel and generate magnetic energy as it spins. The magnets will eventually build up enough energy to fire off high-voltage sparks.
What kind of parts do lawn mowers use?
Different lawn mower brands make their components differently. Some will use plastic instead of metal for certain components. Plastic parts will wear out faster, and are less capable of withstanding the stresses of consistent use.
How to check if pawls are broken?
To check if the pawls on your mower are broken, remove the starter and pull the rope to make them pull out. If they don’t pull out, either they’re broken or something else is broken.
Why is my lawn mower not starting?
The pawls are the most likely component to fail and it’s probably why your mower isn’t starting. That said, if the pulley or receiver is damaged, that will also cause issues.
Where is the starter rope on a walk behind mower?
The starter rope is wrapped around a pulley system. That allows it to be pulled out before it recoils into the engine. The pulley sits below the cover at the top of your walk-behind mower, and a spring is in the center of the pulley. As it’s turned, the recoil spring stretches, then snaps back when let go. This immediate snap-back retracts the pull cord and allows you to pull the rope quickly one time after another.
What is the starter rope on a lawn mower?
The starter rope is the only part of the starting system that can be seen. But inside your mower, the rope activates a series of parts that start the engine.
