The proper method of repair depends on the severity of the scratches. For deep scratches in TimberTech decking, the application of heat with a soldering iron or heat gun can make the damaged area less visible. If using a soldering iron, slide the rounded point of the tip of the soldering iron into the scratch.
Is TimberTech better than Trex?
Keep in mind this is a factor with only a very small percentage of decks. For the vast majority of homeowners both Trex and Timbertech will perform great. Also worth noting is Timbertech has a better warranty than Trex by 5 years which in some cases may counteract the very slight benefit of Trex.
What is the best deck cleaner?
- BEST OVERALL: STAR BRITE Non-Skid Deck Cleaner & Protectant
- ECO PICK: Simple Green Oxy Solve Total Outdoor Cleaner
- BEST FOR MOLD AND MILDEW: Wet & Forget Moss, Mold, Mildew & Algae Stain Remover
- BEST FOR OIL AND GREASE: Oil Eater Original Cleaner/Degreaser
- BEST ALGAE CONTROL: CITRA-SHIELD EXTERIOR ALGAE CONTROL SYSTEMS
How to clean and maintain composite decking?
- Pressure washers can damage the boards of your deck if they're not used carefully. ...
- Stay at least 8 inches (20.32 cm) away from the deck surface at all times and spray in the direction of the wood grain to avoid possible damage.
- Make sure you rinse away the soap thoroughly; otherwise, it may leave a film on the deck surface.
How to clean engineered wood deck?
- Sweep first.
- Wash away debris.
- Apply cleaner.
- Seal the deck.
Can you repair composite decking?
Repair the decorative board damage with filler If the boards on your WPC decking have chips or small cracks. You can use a composite deck repair kit to repair them-it depending on the material and manufacturer of your boards. These repair kits usually consist of wax or epoxy-based fillers.
How do you repair damaged composite wood?
Composite Decking Scratch Repair TipsFill nicks and scratches with an epoxy-based filler and a putty knife. ... Try the heat method. ... Replace scratched boards with new ones. ... Consider consulting the manufacturer or retailer about your scratched decking.
How do you fix a cracked composite deck?
Use a putty knife to force the putty deeper into the crack. If the crack has a small depression after you've used the putty knife, add more filler and repeat forcing the crack full until it's flush with filler. Allow the filler to dry overnight or according to the manufacturer's recommendations.
Is it OK to pressure wash TimberTech decking?
A power washer can be used for RINSING ONLY with TimberTech Deck or Porch. The recommended maximum pressure is 1,500 psi. A fan tip nozzle should be used. Spray in the direction of the grain pattern, never across the grain, to avoid damaging the product.
Is there a filler for composite decking?
For small scratches and surface marks, a Composite Decking Repair kit may be the best thing to help you fix your damaged Board. Repair kits often include wax or epoxy fillers to help remove/ cover up any scratched areas of your Deck.
How often do you have to replace composite decking?
That's one of the main advantages of our preferred composite material: the average composite deck lifespan is at least 25 to 30 years, and can span even longer. At Keystone Custom Decks, we build using Trex and TimberTech composite decking, both of which are known for their gorgeous styles and long lifespans.
How do you fill a hole in a composite deck?
For plastic or composite decking, use an epoxy filler to fill screw holes. Mix the epoxy with thinner and use a syringe to fill the holes. Allow the epoxy to dry, then sand it so that it is flush with the deck.
Do cracked deck boards need to be replaced?
Deck Boards Are Cracked While splinters could injure your bare feet and hands, they're also a sign that your deck is losing its stability. If you notice that most of the boards have cracked, you should get the whole deck replaced.
Why is my composite deck peeling?
0:171:48Common Composite Decking Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe most common problems composite deck owners face are algae mold and surface peeling many believeMoreThe most common problems composite deck owners face are algae mold and surface peeling many believe that moisture is the primary.
Can you use Dawn to clean composite decking?
For grease and oil stains, apply a few drops of liquid dish detergent such as Dawn. This will power through the grease and lift it from the surface without damaging the composite decking. Use a handheld scrub brush dipped in warm water to whisk away the oily stain.
How do you restore a composite deck?
How to clean and restore a composite deckMaterials List.Clean the deck: Sweep excess debris (dirt and leaves) off the deck. ... Apply the composite deck stain: Stir product thoroughly. ... Clean-up: ... Frequently Asked Questions.Maintenance.
Can you put salt on TimberTech?
Both Azek and Timbertech allow you to use rock salt or calcium chloride on their CPVC and composite decking. Just make sure you get the kind that is safe for concrete, plants etc.
How do you repair a composite?
The steps involved in composite repair are:Detect and assess the damage.Identify component.Remove Paint.Design the repair.Obtain materials and tools.Remove the damaged area.Effect the repair.Allow proper curing time.
How do you fill a hole in a composite deck?
For plastic or composite decking, use an epoxy filler to fill screw holes. Mix the epoxy with thinner and use a syringe to fill the holes. Allow the epoxy to dry, then sand it so that it is flush with the deck.
Why is my composite deck peeling?
0:171:48Common Composite Decking Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe most common problems composite deck owners face are algae mold and surface peeling many believeMoreThe most common problems composite deck owners face are algae mold and surface peeling many believe that moisture is the primary.
How do you fill gaps in composite decking?
Fill small holes, using a putty knife, with a mixture of fine composite board shavings and silicone caulk. The consistency of the mixture should be thick enough that it will not seep out of the bottom of the hole. Match the color of the caulk to the deck boards.
What pressure should I use for a Timbertech deck?
A power washer can be used for RINSING ONLY with TimberTech Deck or Porch. The recommended maximum pressure is 1,500 psi. A fan tip nozzle should be used. Spray in the direction of the grain pattern, never across the grain, to avoid damaging the product. Use caution not to damage the material and always take proper safety precautions when operating a power washer.
What is the best way to clean a deck?
In preparation for cleaning you will need water for rinsing (hose or power washer), the recommended deck brush with an extension handle , and TimberTech DeckCleaner. Important: Clean in small, manageable areas. Thoroughly rinse each area before moving onto the next section and do not let the cleaner dry on the surface.
What causes mildew on wood deck?
Mildew stains may occur where moisture, pollens, and/or dirt are present. Mildew needs a food source to grow, which can be grass, pollens, dirt, debris, wood, and wood resins. Maintaining a clean dry surface is the best method for combating mildew. Ensure that water drains effectively from your deck.
Can you use Corte Clean with Timbertech?
Note that composite deck cleaners such as Corte Clean®, Thompson’s® Water Seal®-Oxy Action, Olympic® Deck Cleaner, or other cleaners specified as composite deck cleaners, in powder or liquid form, should not be used with TimberTech AZEK Deck or Porch, TimberTech PRO, and TimberTech EDGE collections. The capping material on these products is not composed of a wood plastic composite.
Is Timbertech docksider the same as reliaboard?
ReliaBoard and DockSider are composite products, and cleaning is NOT the same as for capped composite products such as TimberTech PRO and EDGE Collections.
Is Corte deck cleaner a composite?
Note that composite deck cleaners such as Corte Clean, Thompson’s Water Seal-Oxy Action, Olympic Deck Cleaner, or other cleaners specified as composite deck cleaners, in powder or liquid form. The capping is a polymer and not a wood/plastic composite.
Can you use metal shovels on a deck?
Metal shovels or plastic shovels with a metal leading edge will damage the surface of an TimberTech Deck or Porch and are not recommended for clearing snow from deck surface.
Why do we need to maintain decks?
Decks need regular maintenance to retain their appearance and structural integrity. When done properly and routinely, deck maintenance can increase your deck’s lifespan and reduce the likelihood of future repairs or replacements. In brief, deck maintenance protects your outdoor living space investment.
What is the purpose of deck inspection?
Performing an annual deck inspection of the surface and substructure helps you catch problems — such as loose or rusted fasteners, moisture damage at ground contact, or joist issues — before they develop into larger (and more costly) problems like full deck replacement.
Can you clean a composite deck in direct sunlight?
Don’t clean the deck in direct sunlight, as it could cause the cleaner to dry too quickly. This will cause a white residue which will need to be washed again. Don’t use other brands of composite deck cleaner. Many of these cleaners are designed for traditional uncapped composite deck boards.
Can you use bleach to clean a deck?
Don’t use chlorine bleach to clean your deck. Chlorine is a harsh chemical that will strip your wood deck of its natural color and may even damage the structural integrity of the boards. Don’t use paint as a sealant.
Is TimberTech decking weather resistant?
TimberTech capped polymer and capped composite decking is moisture- and weather-resistant, so your deck surface is unlikely to develop the problems associated with a traditional wood deck.
Deep Scratches
For deep scratches in TimberTech decking, the application of heat with a soldering iron or heat gun can make the damaged area less visible. If using a soldering iron, slide the rounded point of the tip of the soldering iron into the scratch. The scratched area will melt and return to its original color.
Minor Scuffs and Scrapes
Minor scratches, nicks, scuffs and cuts can be removed from TimberTech decking using a wire brush. Work in the direction of the grain and gently buff out the damage. The area will appear darker initially, but will weather to blend with the surrounding material in about 8 to 10 weeks.
What is the best way to finish composite decking?
End coating is the easiest option for how to finish the ends of composite decking and requires no tools but a paint brush.
What is end coating?
End coatingrefers to a type of paint you apply to your end-cuts. As an option for how to finish the ends of composite decking, end coating is ideal for just a few exposed ends. This is the case because end coating does not offer the same level of protection — nor as sophisticated an aesthetic — as fascia or a picture frame border.
What is fascia board?
Fascia board, sometimes called “deck fascia” or “rim joist cover,” refers to the board used to cover the end-cuts and rim joists of your deck’s frame. In most instances, you can use an actual fascia board for the application or a deck board in place of fascia board.
Is fascia board easy to install?
Plus, fascia board is straightforward to install, with some guidance, even for first-time DIYers.
What is composite decking made of?
Composite decking is typically made of wood fibers combined with plastic. The term is fluid, however, in that some manufacturers sell composites that are entirely made of plastic or are plastic wrapped around a wood core. Because of this, composite deck scratch repair can take a little bit of preliminary research before you tackle ...
Can you contact the manufacturer of composite decking?
Whenever possible, contact the manufacturer of your composite decking for solutions to problems with your deck. The company can offer advice based on the type of composite decking material you own.
Can you sand composite decks?
Composite planks exposed to sunlight eventually lose their luster and become discolored. Sanding is not an option for composites. The plastic burns and melts with heavy friction, and the discoloration problem could worsen instead of improve. Paints are also not recommended because they tend not to adhere well to composite material. Stains, however, will recolor a composite deck, although the color may vary from what’s shown on the can. Always try a sample of stain in an inconspicuous portion of the deck before investing time and money in staining the entire deck.
Can composite decking be scratched?
Similar to wood decks, composite materials are prone to scratches and dings from moving outdoor furniture. Solutions vary by manufacturer and by product type. Some recommend not working scratches and abrasions as they will blend with the rest of the decking in time.
Why is my deck faded?
Fading is caused by weathering and is natural for all deck products. While early versions of TimberTech decking faded rapidly, the addition of a bonded protector eliminates unusual fading. Paints or refinishers revitalize a faded surface but require reapplication, offsetting a benefit of composite materials. Any finishing product requires precleaning and applying according to the manufacturer's instructions.
What is the best time to clean a deck?
TimberTech recommends the regular use of environmentally friendly deck-cleaning products. Performing the process in the early morning or late evening prevents evaporation and powdery residues.
Does TimberTech decking have mold?
Scratching, fading, mold, heat buildup and becoming slippery when wet are some problems reported for TimberTech decking , as of 2015. Structural integrity risks are less prevalent and are mitigated by following installation recommendations.
