
To repair this problem:
- Loosen the set screws under the towel bar and remove it from the wall.
- Loosen the bracket screws and remove the brackets from the wall.
- Insert toggle bolts in each bracket.
- If needed, enlarge the bracket holes in the drywall with a screwdriver, and insert the toggle bolts in the holes.
- Tighten the toggle bolts so the brackets are secure.
- Mount the towel rack on the wall and tighten the set screws.
How to repair a loose towel rack?
To repair this problem:
- Loosen the set screws under the towel bar and remove it from the wall.
- Loosen the bracket screws and remove the brackets from the wall.
- Insert toggle bolts in each bracket.
- If needed, enlarge the bracket holes in the drywall with a screwdriver, and insert the toggle bolts in the holes.
- Tighten the toggle bolts so the brackets are secure.
How do you remove a towel rack from the wall?
To remove a ceramic fixture, such as a towel rack, from a drywall surface, you must:
- Cut through the plastic bar that spans between the two ceramic posts.
- Tape the wall around the base of each ceramic towel bar post.
- Use an oscillating multi-tool to cut through the adhesive between the wall and the towel bar holders.
- If absolutely necessary use a hammer along with a chisel or pry bar to pop the towel bar holders from the wall.
How to take a towel rack off the wall?
Removing A Towel Bar From The Wall
- Find the Screws. Depending on the towel bar that you own, there may be screws fastening it to the wall. ...
- Remove the Screws. Using a hex key or Phillips head screwdriver, you can now remove the screws from the towel bar. ...
- Remove the Wall Brackets. If your towel bar is attached to wall brackets, you will need to remove them. ...
- Patch the Holes. ...
How to attach a towel rack to recessed drywall?
- Using the set screw and wrench provided with your towel bar, attach one of the bar holders to the bracket.
- Slide the bar into place and attach the next bar holder.
- Put a little pressure on the towel bar to make sure it is secure.
- Hang towels.

How do you fix a drywall rack?
1:154:04ULTIMATE TOWEL BAR REPAIR HACK - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you don't have to fix the hole or anything like that okay so what we're gonna do is we're goingMoreSo you don't have to fix the hole or anything like that okay so what we're gonna do is we're going to shake this up. And we're gonna try to get some of this great stuff this expanding foam.
How do you cover a hole in a towel rack?
1:453:08How to Repair a Hole in Drywall / Wall from Towel Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold it there so it doesn't crumble away don't put two pieces of drywall tape over this. And then weMoreHold it there so it doesn't crumble away don't put two pieces of drywall tape over this. And then we'll see with our drywall. Cover press back over this you can want to use nice.
How do you fix a bathroom towel rack?
2:233:52Bathroom towel bar repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipI can go ahead and take the towel bar. Slide it over the brackets. Take my allen wrench andMoreI can go ahead and take the towel bar. Slide it over the brackets. Take my allen wrench and retighten the set screw in the bottom of the towel bar. So that it tightens against the brackets.
How do you fix a screw hole that is too big for drywall?
All you have to do is fill the hole with a little glue and the appropriately-sized plug or dowel. Let the glue cure for about 24 hours, and then drill a pilot hole into the center of the plug to make room for your new screw.
How do you fix a ceramic towel rack?
0:131:35How To Install A Replacement Towel Bar - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide it into the holder. Push it side to side to little center itself. So with the bar in placeMoreSlide it into the holder. Push it side to side to little center itself. So with the bar in place that's it you just replace the bar. And your towel bar holder with the porcelain.
How do you fix a hole in a toilet paper holder?
0:004:44How to fix a ripped out toilet paper holder or towel rod - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut in this case to fix it all we need to do is pop by some toggle bolts and what they are going toMoreBut in this case to fix it all we need to do is pop by some toggle bolts and what they are going to note that these are available in most hardware stores. And they aren't whispers.
How do I fix a hole in my bathroom wall?
0:061:23How to Patch a Hole in a Bathroom Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst I cut a rectangular drywall patch and place it over the damaged area tracing around it with aMoreFirst I cut a rectangular drywall patch and place it over the damaged area tracing around it with a felt pen. Next I cut out the shape with a drywall saw.
What do you need to patch a hole in a wall?
MaterialsConstruction Adhesive.Drywall Tape.Masking Tape.Drywall Screws.Joint Compound.Drywall Patch Kit.Drywall Scraps.Drywall Patch Plaster.More items...
Step 2: Clean the Attachment Plate for Your Towel Rack
Our towel rack has a separate plate that attaches to the wall first, and then the arm that holds the towel rack is tightened onto the plate.
Step 3: Put Toggle Bolts on Attachment Plate
Toggle bolts come in two pieces - the bolt and the then toggle, which is a spring loaded v-shaped nut that helps provide traction on the other side of the wall. You'll want to insert the bolts through the attachment plate to prepare for the install.
Step 4: Insert Toggle Bolts Through Wall
Pinch all toggles closed and carefully insert them though the holes in the wall.
Step 5: Tighten Attachment Plate to Wall
To tighten the bolts and secure the attachment plate in place, you'll need to pull forward on on the plate, creating tension on the toggles.
Step 6: Attach Rest of Towel Rack and Enjoy!
Once the attachment plate is in place, you can install the rest of the towel rack and then hang your towels.
What to use to fix a towel rack that is loose?
Toggle Bolt will fix almost all towel racks that come loose from drywall! Extremely simple fix unless the hole is very large then you need to drywall patch and then I’d still probably use a Toggle Bolt !
What is the best way to anchor drywall?
A quick and reasonably sturdy solution is to use plastic drywall anchors or toggle bolts.
Do towel bars need to be sized up?
With this latter approach it may be desirable to size up the room and if there are other towel bars present you may want to install these board strips in a uniform manner for those as well to maintain a style in the room.
Can you glue paper to towel bars?
If you saved some of the original wall paper it is also possible to glue wall paper onto these strips after they have been primed. Done carefully the wall paper pattern can be matched to the wall and make the towel bar mounting boards hardly noticeable.
