If all else fails, try resetting the speaker to its factory default settings by following these steps: Hold down the “volume down” and “power” button at the same time until you hear a sound. The UE Boom 2 will then turn off. Turn the speaker back on and attempt to pair it with your device again..
Full Answer
What do I do if my UE BOOM 2 won't connect?
Try moving the device you are trying to connect closer to the speaker and attempt to connect. If all else fails, try resetting the speaker to its factory default settings by following these steps: Hold down the “volume down” and “power” button at the same time until you hear a sound. The UE Boom 2 will then turn off.
Why does the UE BOOM 2 app keep crashing?
Make sure the version of the UE Boom 2 App running on your device is the current version. Go to the App Store/Google Play Store on your device and check for any updates. If there is an update, install it, and reattempt to connect the app to your speaker. If two devices are connected to the speaker at once, launching the app may cause it to crash.
What is the difference between UE Boom and UE BOOM 2?
The Logitech UE Boom 2 is a portable, stain-resistant, shock-resistant, and fully waterproof, Bluetooth speaker. The visible difference between the UE Boom and UE Boom 2 is very limited.
Is the Logitech UE BOOM 2 Waterproof?
The Logitech UE Boom 2 is a waterproof, portable Bluetooth speaker known for its 360 degree sound. The Boom 2 comes in a multitude of vibrant colors and patterns.
How do you fix a blown UE Boom?
3:135:58Ultimate Ears UE Megaboom Bad Blown Broken Speaker ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou grab your replacement speaker plug it in grab your long hinge pins. And slide them through likeMoreYou grab your replacement speaker plug it in grab your long hinge pins. And slide them through like this use your pliers to shove the hinge pin. In. I've done that you can start replacing.
How do I reset my UE Boom 2 speaker?
Factory Reset NeededHold down the “volume down” and “power” button at the same time until you hear a sound. The UE Boom 2 will then turn off.Turn the speaker back on and attempt to pair it with your device again..
Can you replace battery on UE Boom 2?
The battery is located under the top cover of the UE Boom 2. It is held in place by 4 screws and can be replace with a single screwdriver and a spudger.
How do I fix my UE Boom 2 not charging?
If the speaker is refusing to charge, it may need a factory reset. Press and hold down both the volume button and the power button for about ten seconds or until you hear the speaker make a sound. After the sound, the speaker should turn off. Now, try turning the speaker on again.
Why is my UE Boom not working?
If you have two devices paired to the speaker and attempt to launch the application on your Android phone, it may crash. To fix this, disconnect both devices from the speaker and reconnect the one you wish to play music from.
How do I force UE Boom to reboot?
Press the Volume “–” and Power buttons simultaneously and hold for at least six seconds. You'll hear a tone that indicates the reset was done and your speaker then should turn off. This reset will bring your speaker back to factory settings.
How long does UE Boom 2 battery last?
15 hoursHow long does the UE BOOM 2 battery last? In our testing, we got close to 12 hours of constant playback for the UE BOOM 2. Like the original BOOM, UE claims a battery life of 15 hours but also like the original it fails to live up to that expectation.
How do I fix my UE boom battery?
0:1326:09UE Boom Battery Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipHey guys I'm going to show you how to do a quick battery placement on this you eat boom here. It'sMoreHey guys I'm going to show you how to do a quick battery placement on this you eat boom here. It's not a hole in charge or a long.
How do I check my UE Boom 2 battery?
You can check the battery level of your WONDERBOOM 2 by pressing both the volume + and volume – buttons simultaneously. If you hear this tone, it means that your WONDERBOOM 2 is juiced up and ready to go!
How do I fix my UE Boom charging port?
0:019:15Ultimate Ears UE Boom 2 Charger Port Replacement Not Charging No ...YouTubeStart of suggested clipEnd of suggested clipSo let's get to it to begin let's get flip it to the backside where the port is located and use aMoreSo let's get to it to begin let's get flip it to the backside where the port is located and use a pry tool to pry it back this spine.
Why is my UE Boom charging light flashing?
Charging Time: The user manual states that the speaker will completely charge in about 2.5 hours. The Power LED light will shine red when the battery is low then flash red when the battery is just about dead. After you plug in the speaker to charge, a small white LED light above the micro-USB port will start flashing.
What is the warranty on UE Boom?
A: No, all ULTIMATE EARS BOOM models carry the same 2 year limited warranty.
Why won't my UE Boom 2 Connect?
If your Bluetooth device won't connect to your ULTIMATE EARS speaker, try the following: Make sure your speaker is turned on. Make sure your device is paired with your speaker and Bluetooth is active. Place your Bluetooth device closer to the speaker – it might be out of range.
How do I reset my Bluetooth speaker?
With most Bluetooth speakers, you should only have to do so for a few seconds. For just about every Bluetooth speaker out there, pressing and holding the power button and Bluetooth button simultaneously will force the speaker to reset.
Why does my UE Boom 2 Keep cutting out?
Well, since it uses Bluetooth technology, your Megaboom speaker could cut out if it's not fully charged; your device is not compatible, is no longer supported or is out of range; interference from other devices, or that the Bluetooth app you are using has a bug or hasn't been updated in ages.
How long does UE Boom 2 battery last?
15 hoursHow long does the UE BOOM 2 battery last? In our testing, we got close to 12 hours of constant playback for the UE BOOM 2. Like the original BOOM, UE claims a battery life of 15 hours but also like the original it fails to live up to that expectation.
How to pair UE Boom 2?
Check and make sure that Bluetooth pairing is enabled on the device you are trying to pair to the speaker. Select the UE Boom 2 from the list of devices, and make sure the UE Boom 2 is ready to be paired with by pressing the Bluetooth button on the speaker (see next problem).
Why is my boom speaker not pairing?
Pairing issues may be caused by differences in firmware. To ensure the same firmware, connect the speakers to your smartphone and install the latest firmware by going to the Boom app, tapping on “More”, checking for updates and downloading them.
How to make sure Bluetooth speaker is in pairing mode?
Make sure your speaker is in pairing mode by pressing and holding the Bluetooth pairing button on your speaker above the power button until the speaker makes a sound . The Bluetooth LED light will begin to blink once this has happened.
How to double up Bluetooth speaker?
If you cannot get “Double-Up” to work with the app, follow these steps to manually double-up: Bluetooth pair your device to the first speaker. Turn on the second speaker. Press the + volume button and Bluetooth button at the same time on the first speaker. (A tone should confirm that it is ready.)
How to check if speaker volume is too low?
Check if the volume on the speaker is too low to hear by pressing the “+” button multiple times
Can two boom speakers play music at the same time?
Two Boom speakers will not play music at the same time.
How to pop a metal wire out of a sleeve?
Pry the metal wire up and out at exactly this gap, then slide down wire towards one end to pop it out completely.
How to pry up mesh lining?
Using the metal spudger tool, pry up the inside edge of the mesh lining.
How to remove rubber stripping?
Remove the rubber stripping using a metal spudger.
Introduction
This guide will show how the motherboard of the UE Boom 2 Bluetooth speaker is removed. This is an extensive and intrusive process which removes all components of the speaker.
Step 1 Motherboard
First, remove the D-ring located on the bottom of the UE Boom 2, the opposite end of the power button.
Step 5
On the bottom, unscrew the four 15mm Phillips head screws, using a #2 Phillips head screwdriver.
Step 6
Now on the top, unscrew the four 15mm Phillips head screws, using a #2 Phillips head screwdriver.
Step 7
Carefully un-loop the cable with a plastic opening tool or spudger and unplug it from motherboard.
Step 9
Using the metal spudger tool, pry up the inside edge of the mesh lining.
Step 10
Unscrew the two 5 mm Phillips head screws using a Phillips head #1 screwdriver.
