Repairing Guides

how to repair vinyl fence hole

by Mr. Lazaro Barton MD Published 3 years ago Updated 2 years ago
image

How to Repair a Vinyl Fence

  1. Clean Vinyl Fence Before you do any repair work to the section of the vinyl fence where the crack is located, you should clean it of any dirt ...
  2. Sand Around Hole in Fence Wrap a piece of medium grit sandpaper around a small block of wood. ...
  3. Use Expanding Foam to Fill Hole Take a look at the hole in the vinyl fence. ...
  4. Saw Foam Off Fence Take a small handsaw, a coping saw works well for this, and remove the excess foam from the fence. ...
  5. Sand Foam After the foam has been cut down, use some medium grit sandpaper to smooth it out flush with the surface of the fence. ...
  6. Clean Surface of Vinyl Fence After all of the sanding, you will need to clean the fence again. ...
  7. Fill Hole With Plastic Filler Using a small plastic scraper, fill in the area where the hole in the fence is. ...
  8. Sand and Paint

Below is a step-by-step guide to repairing cracks and holes in a vinyl fence using auto body filler.
  1. Carve Away Rough Edges.
  2. Sand the Area Around the Damage.
  3. Clean the Immediate Area.
  4. Fill the Opening with Spray Foam.
  5. Seal the Opening with Auto Body Filler.
  6. Paint the Repaired Area.

How do you fill a hole in a vinyl fence?

Take a look at the hole in the vinyl fence. If it is larger than 1 inch in diameter, you will need to use some expanding foam to fill in the hole. Spray the foam into the hole and fill as much of the vinyl fence as you can. Fill the space slowly to allow the foam to expand.

Can a crack in a vinyl fence be repaired?

Here are some steps to repairing a crack, or hole, in a vinyl fence. Before you do any repair work to the section of the vinyl fence where the crack is located, you should clean it of any dirt and debris.

How do you fix a broken rail on a vinyl fence?

If a panel breaks on your vinyl fence, simply remove the top rail and panel from the section you want to replace, slide the new panels into place, and replace the rail. You can also replace the rail by cutting it to length, removing the damaged rail, and sliding the new rail into the holes on the fence post.

How do you reinforce a vinyl fence post?

There are other options – you could reinforce the post with wood or metal insert, use a fence post mender, or fence post spike First, remove the fence post cap to inspect inside the vinyl post.

image

How do I fix a hole in my fence?

Fill the hole by applying the putty with a 1-inch wide putty knife. You'll want a bit of putty out of the hole and on the surrounding area for support. Don't worry about lumps as you'll be sanding it down later. Once the putty is evenly distributed on both sides, let it dry for 12-24 hours after application.

How do you repair a white plastic fence?

0:533:23Vinyl Fence section repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe slide the top rail over lift it up on slide it out of the post. And remove it once the top railMoreWe slide the top rail over lift it up on slide it out of the post. And remove it once the top rail is off it's easy enough to remove the slats.

What is the best glue to repair vinyl fencing?

Veranda PVC cement glue is specifically designed for vinyl fence. The exclusive rapid set formula creates a strong bond for years of enjoyment. Available in 1.5 oz. tubes, it's perfect for installing vinyl post caps on vinyl posts.

How do you repair a plastic fence panel?

0:538:02How To Repair Vinyl Fence | DIY Quick and Easy! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're gonna need to repair the fence you're gonna actually need the panels. Themselves soMoreSo what you're gonna need to repair the fence you're gonna actually need the panels. Themselves so you can buy these kits. At your local hardware. Store. You need a drill in case there's any screws in

Do vinyl fences break easily?

Durability You Can Count On No matter what they're facing, vinyl fences stand strong. They won't rot, blister, or allow the growth of fungus, and you won't have to worry about them splitting or cracking due to weather or old age. Plus, vinyl fences are resistant to fire and impenetrable to pests.

Can I paint a vinyl fence?

Because vinyl fence is a non-porous material, most paint won't adhere to it well. Some paint may stick initially, but in time will completely peel off. If you do paint your vinyl fence, you'll need to choose a primer and paint carefully – ones that are designed for use on vinyl products.

Does Gorilla Glue work on vinyl?

Will Gorilla Glue work on vinyl flooring? According to its makers, Gorilla Glue isn't ideal for use on vinyl floors. In fact, Gorilla Glue is water activated and its polyurethane formula works best on gluing ceramic, metal, foam, glass, stone and wood. That's why it won't work well on vinyl flooring.

What kind of glue works on vinyl?

Polyurethane glue is ideal for gluing thinner flexible vinyl together as well as gluing vinyl to other surfaces like wood or plastic.

Can I use PVC glue on vinyl fence?

PVC Fence Cement is perfect for gluing the post caps onto vinyl fences.

How do you reinforce a vinyl fence?

Strength can be added to a vinyl post by tightening up the post, rails, and pickets around the entire perimeter of the fence. Additionally, adding reinforcement inside specific posts will increase rigidity to high-risk areas.

Are vinyl fences strong?

By nature, vinyl is durable and strong. How durable is vinyl fence? It has five times the tensile strength and four times the flexibility of wood. Vinyl fence material is typically blended with other ingredients to yield a low-maintenance product that will last for years.

How do you repair a vinyl fence post?

0:161:50REPAIR VINYL FENCE EASY! - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing you do is cut all the post to ground level with a skinny. We'll. Use a 5 by 5 by 3 stillMoreFirst thing you do is cut all the post to ground level with a skinny. We'll. Use a 5 by 5 by 3 still insert or support slide the post over the still inserts.

How do you repair a vinyl fence post?

0:161:50REPAIR VINYL FENCE EASY! - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing you do is cut all the post to ground level with a skinny. We'll. Use a 5 by 5 by 3 stillMoreFirst thing you do is cut all the post to ground level with a skinny. We'll. Use a 5 by 5 by 3 still insert or support slide the post over the still inserts.

How do you reinforce a vinyl fence?

Strength can be added to a vinyl post by tightening up the post, rails, and pickets around the entire perimeter of the fence. Additionally, adding reinforcement inside specific posts will increase rigidity to high-risk areas.

How do you remove the bottom rail from a vinyl fence?

Apply pressure to post as you pull on the rail and try to force it out of the route. If you cannot pull the rail out of the post, use a rubber mallet to knock it free. Pull on the rail and tap on the post with the mallet until it frees. Remove the bottom rail of the fence, following the same process.

How do you remove plastic fence posts?

2:2515:04Remove Vinyl Fence Posts WITH Concrete! SUPER EASY! - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing we want to do is try to level out the surface around the post. So that we're workingMoreFirst thing we want to do is try to level out the surface around the post. So that we're working with. What we call grade try to make sure that everything is at grade level.

How to get replacement fence panels?

Order similar replacement panels. You can search online to find many different fence styles. If you can , contact the fence’s manufacturer to get new panels identical to the old ones. Take a picture of your fence and send it to companies to ensure you get the right panels.

What to do if a post gets damaged?

If one of the posts gets damaged, unscrew the top rails, dig up the damaged post, set the new post in place with concrete, and reattach the rails and panels.

How to cut a rail?

Cut the rail to length with a circular saw. Set the new rail on a workbench. Before cutting, mark where you need to make the cuts so you get the size of rail you need. Then, carefully cut through the rail.

What to do if your rail doesn't fit?

If the rail doesn’t fit properly, check the length again. You may need to cut it a little shorter.

What to wear when sawing into rails?

Wear safety goggles and other protective gear. Before sawing into the rails, take the proper safety precautions. Shield your eyes from debris by wearing safety goggles. Cover your mouth by wearing a respirator.

How to move a panel to the side of a post?

If the panel is next to a post, it may be attached with side brackets. Carefully move the panel to the side and out of the brackets.

Do vinyl fences need maintenance?

Vinyl fences are very resilient, so they don’t require a lot of maintenance. If some part does break, your fence is also easy to take apart and reassemble. The most difficult task is finding an identical replacement piece. Once you have it, you can quickly connect it to the existing parts.

How to fix a hole in vinyl?

Sand down the area around the hole. The creators of this prouduct recommend sanding about 8 inches around the problem area. Afterward, wipe off any excess vinyl you sanded.

What to do if your fence is fading after washing?

After washing your fence, you may notice some of the shine is gone. The best solution is to find a good wax or house wax. Rubbing this on your fence will help it get its beautiful shine back. You can also try this Vinyl Guard to give it a nice coating and protect it from fading or cracking under future pressure.

How to get rid of vinyl shards?

Sand. Sand the area around the hole to get rid of any excess vinyl shards. Also, smooth the edges of the hole down if you can.

Can you pressure wash vinyl fence?

However, it is possible to use a pressure washer on your vinyl fence. It is great for getting a lot of dirt and stains off without having to scrub it all by hand. However, it is recommended to use a setting between 500 and 800 PSI on the fence so you don’t create a new hole in it. You should also check with your pressure washer manual specifically to see what it says to do when it comes to vinyl.

Can you sand a vinyl fence?

Vinyl Fencing can be sanded by hand using medium or fine-grit sandpaper. Using a power sander on a vinyl fence should be avoided as it can cause additional damage. It’s only necessary to sand a vinyl fence when repairing damage and not as part of routine maintenance.

Is vinyl fence repair good?

This method of vinyl fence repair is a bit more sturdy because you are actually filling the hole instead of just covering it. This is good because it makes it less likely to break again. It has a similar process to the kit above, but this one does take a little longer. This method is also very common among people in the fence repair business and is highly recommended.

Can you use a power sander on vinyl fencing?

It is also important to note that you should not use a power sander on your vinyl fencing. They are too powerful and too aggressive to remove the vinyl. In addition, they may leave permanent marks. Also, no matter how steady your hand is, the power sander might create another hole in the fence. Sanding by hand is much safer.

What is a vinyl fence?

Spray Paint. A vinyl fence is a very popular form of fencing for many urban homes. The vinyl fence not only adds an attractive element to a landscape, but it is low in maintenance. These vinyl fences are mostly made of a non porous material that makes cleaning very easy.

How to smooth out vinyl?

Wrap a piece of medium grit sandpaper around a small block of wood. You do not want to use an electric sander for this operation, as you can gouge the vinyl or remove excess material. You are only trying to smooth out any burs and sharp edges around the hole. Rub the sandpaper in an area that is about 3 inches around the hole.

How to make a dent in a foam fence?

After the foam has been cut down, use some medium grit sandpaper to smooth it out flush with the surface of the fence . Then, begin to concave the foam to form an inward dent.

How to fill a hole in a fence with plastic?

Apply plastic automotive body filler to the foam-filled hole with a putty knife. Overlap the filler onto the fence immediately surrounding the hole. Allow the plastic filler to dry thoroughly, following the manufacturer's instructions.

How to sand a hole in a wall?

Rough the area around the hole with 80-grit sandpaper. Rub the sandpaper around the hole to scuff the area and create a surface that materials can more readily adhere to. Wipe sanding debris from around the hole with the damp rag.

How to sand plastic filler?

Sand the plastic filler with progressively finer sandpaper, beginning with 80-grit and ending with 180. Wipe the sanding dust away and spray with paint designed to adhere and bond with plastic surfaces.

Is vinyl fencing more attractive than metal?

By Tara Shore. Vinyl fencing can be a more attractive option than wood or metal as it is resistant to weathering and keeps its color without the need for washing or painting. However, as resilient as it may be, a vinyl fence can be damaged by falling limbs or other events that create a hole.

What to do if you have a hole in a fence?

If you have a hole that exceeds an eighth of an inch in width, a backing will be needed for your filler. If you don’t do this, the filler is going to sag or possibly even fall out of your fence’s opening entirely. This type of job is best handled with a spray foam that helps insulate people’s homes.

What to use to smooth out rough edges on vinyl fence?

They also look unsightly for your fence. A utility knife should be your tool of choice for smoothing out these rough edges. If you cut a bevel along your vinyl’s edge, you’ll have a much easier time applying filler later.

How to clean foam from a sandbox?

Once the opening has been filled, use a cloth soaked with alcohol to wipe off all of the foam that spilled. Then, allow the foam to dry.

Can vinyl fences get damaged?

With that said, there are ways your vinyl fence can get damaged. Strong temperatures, both heat and cold, can do a number to your fencing. Once your fence is damaged, it becomes easier to accumulate additional damage if you don’t act quickly. Swift repairs are a must to avoid too much damage. Here is how you can repair your vinyl fence ...

Is vinyl fencing good?

Vinyl fencing has been known for its great appearance, sturdiness, and fair pricing. It is made from materials that don’t require much upkeep to remain in good condition, meaning not much effort is needed to get a good-looking fence. With that said, there are ways your vinyl fence can get damaged. Strong temperatures, both heat ...

Can you paint vinyl before painting?

Lastly, paint the previously damaged area. The paint you use should be capable of sticking to vinyl, or you can elect to apply a primer coat before painting. A primer coat helps with adhesion.

Is Privacy Fence a good company?

Privacy Fence!!!! This company is fantastic and extremely professional. I would highly recommend to anyone who is looking to install a privacy fence. I love love my fence it is so beautiful and it... Read more

How Much Does It Cost to Repair a Vinyl Fence?

Repairing a vinyl fence can cost you anywhere from $5 to over $1,000, depending on the damage and whether you can fix the broken part or have to replace it.

Why replace vinyl fence panels?

Replacing a vinyl fence panel may be necessary if the holes are too large or the cracks are too many to fill and repair. Here’s how to do it:

How long does it take for foam to dry on a vinyl fence?

When the foam is completely dry – after about 8-12 hours – use a fine tooth saw to cut off any excess foam that has expanded beyond the hole. Cut as flush as possible to the vinyl fence, then use medium grit sandpaper (80-grit) to level the surface until the foam filling is slightly concave. Wipe clean with a damp cloth and let dry.

How to remove plastic filler from a sandpaper?

Using fine-grit sandpaper (180-grit), remove any plastic filler excess. Don’t exaggerate during this step; just sand the area until the surface is perfectly flush. Wipe with a damp cloth and let dry.

How much does it cost to repair a cracked panel?

Repair kits for small cracks and holes cost about $30-$40, which is far less than replacing the entire damaged panel.

How much does it cost to replace a picket?

Broken slats or pickets, for instance, are inexpensive and easy to replace if needed. A new slat or picket costs around $5, and you won’t incur additional costs if you replace it yourself. Minor cracks and holes are also inexpensive to repair.

Can you paint a fence white?

Once the surface is dry, use appropriate plastic or vinyl paint in a color that matches the rest of your fence. Alternatively, you can apply a thin coat of transparent paint if your fence is white. When you’re happy with the result, let it dry, and your repair is complete.

How deep should a PVC fence post be?

Post holes should be deep enough to hold 1/3 the length of your post, plus 6 more inches for a gravel base.

What is the best material to use for a fence post?

For new fence installation, aluminum metal inserts (also known as a fence post stiffener) will hold up the best in high wind conditions. They are also more resistant to water. Used galvanized steel inserts for gate applications.

Can you replace a galvanized post chain link fence with vinyl?

If you are considering replacing a galvanized post chain link fence with vinyl, know that using that as your insert will probably not work. If you use a good make fence, the posts are cut out for the top and bottom rails to slide in, otherwise the round galvanized pipe will be in the way. Panel spacing is also an issue. Most vinyl fence panels are 6 or 8 feet wide.

Is vinyl fence good for inclement weather?

Vinyl fences are durable and affordable, but they are not totally resistant to damage, or inclement weather. The natural expansion and contraction of vinyl and the effects of wind and water may start to produce gaps in the fence and post support. It's possible that the concrete holding it in place has broken up, or the post itself could be cracked or rotted.

Can you repair a rotten fence post?

If you are repairing an existing post with a rotten wood insert, there is still hope! You can add new support and stability using a fence post mender , or fence post spike .

Can you reinforce a fence post with wood?

The good news is you may not need to go through all of this work. There are other options – you could reinforce the post with wood or metal insert, use a fence post mender, or fence post spike

Can you put concrete on a post?

Another thing we have seen is rebar with poured concrete at the base of the post. This may be a cheap and easy solution short term, but the cement is likely to expand and crack the base.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9