DIY Fix for a Dented Bumper
- Get Access Behind the Bumper. Depending on the location of the dent on your bumper, you may need to remove the fender...
- Apply Heat to the Dent. Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer...
- Gently Push Out the Dent. Use a rubber-tipped dowel or specialty tool (like the one shown in the...
Full Answer
How much does it cost to fix a dent in a car bumper?
For the safety of your vehicle, it’s important to repair the bumper whether the dent is minor or not. You can budget about $50 to $600 for minor damage depending on the extent of the damage. In a situation your bumper needs to be replaced entirely, it might cost you about $800 to $2000.
How to repair a dented bumper with a heat gun?
Heat up the dented area in your bumper. In our case, we are using a hot air gun. Set the hot air gun at 650 degrees Fahrenheit. Keep the hot air gun 8 inches away from the bumper. Pay close attention to the paint. Don't keep the heat gun to close, or you will melt the paint.
How to fix a dented bumper?
Fix a dented bumper with boiling water. Boil a pot of water and pour it over the dented area on your bumper. Reach behind the bumper and pop the dent out. You might also need to take the bumper off if the dent can't be reached. Finally, pour a pot of cold water onto the bumper to cool and fix the plastic area. Click to see full answer.
How to repair a bumper Dent with a hair dryer?
Part 3 of 3: Dry ice
- Heat dented region. As in the previous method, do your best to access both sides of the dent and heat the dented region with your hair dryer until ...
- Place aluminum foil over dent. Place a piece of aluminum foil over the dent, using masking tape at the corners to hold it in place.
- Rub dry ice. ...
- Clean up. ...
How do I fix a dent in my bumper?
0:391:51How to fix a dent on the front or rear bumper cover on your ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying theMoreYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying the heat to the surface push out the dent using piece of wood.
Can dents in bumper be repaired?
If they are small in size and confined to one area, these dents can usually be repaired. It's important that the dent did not result in damage to other portions of the bumper. Auto shops that offer dent repair in Salt Lake City can pull out the dent and repair any paint damage.
How do you pop a dent out of a plastic bumper?
Apply boiling water to the dented area. Reach under the wheel well and try to pop out the dent. Aim a heat gun or hair dryer at the dented area for about three minutes. Pay close attention to make sure it's not damaging the paint. When it's hot, try to pop out the dent.
How much does a dent in a bumper cost to fix?
If you just need to have the dent pulled back out and into place, the repair will likely cost $50-$100. However, if the dent is very deep and the paint was damaged as well, you could be looking at a repair of around $200-$1,000, depending on the dent and your chosen repair shop.
Can plastic bumpers be repaired?
Many plastic bumper parts can be repaired, especially bumper covers, which are commonly damaged on a vehicle. By saving your bumper, the technician will also be able to blend the appended paint more efficiently and accurately.
How do you pop out a dent?
0:413:15How to Remove Car Dents Fast - YouTubeYouTubeStart of suggested clipEnd of suggested clipSome water on your stove in a big pan. And pour it all over the dent area then put the suction cupMoreSome water on your stove in a big pan. And pour it all over the dent area then put the suction cup on it'll all batter. Plus the heat off and makes the metal. Get more flexible.
Does boiling water remove dents in cars?
Use boiling water Don't just limit your use of boiling water for cooking and sanitary purposes. It can also be used to potentially remove unwanted depressions in your vehicle, that is, as long as you have a plastic bumper and are successfully able to access the dent from the backside.
Do dent pullers work?
Do they work? Dent pullers only work on shallow dents that are positioned on a flat, flexible surface. They can improve the appearance of car dents but are unlikely to create a perfect finish. Unfortunately, DIY dent pullers will not work on deep, angular dents or damage along the edges of bodywork.
How do you get a dent out of a bumper with a plunger?
Put the plunger over the indented area and pull straight out. Your dent should pop right out. If you're working on a bumper, you can also reach behind the dented surface to push the dent out. Repeat as needed until the dented area is flattened out.
Is it cheaper to repair or replace a bumper?
Bumper repair can be performed in-shop and is often cheaper than bumper replacement. Bumper repair normally costs between $100 and $1,000.
How do you repair a plastic bumper?
0:583:13Proper Repair of Crack or Tear on Plastic Bumper Products - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a DA with P 80 grit to rough up the backside for the reinforcement repair blow off the repairMoreUse a DA with P 80 grit to rough up the backside for the reinforcement repair blow off the repair with clean dry air and apply a light coat of adhesion. Promoter. Allow ten minutes of drying time.
How long does it take to repair a bumper dent?
Standard dent repair can take anywhere from a couple days to 2 weeks. The biggest factor that contributes to the repair timeline is paint work – that is why paintless dent repair can happen so fast. Once the damage is repaired and the surface is perfectly smooth, the technician can begin painting.
Is it cheaper to repair or replace a bumper?
Bumper repair can be performed in-shop and is often cheaper than bumper replacement. Bumper repair normally costs between $100 and $1,000.
Can you repair bumper without replacing?
The Bumper is Cracked If the bumper on the car is cracked, it typically needs to be replaced, rather than repaired. There are a few exceptions to this, as epoxy and a fiberglass repair kit can be used to repair a bumper.
Can you drive around with a dented bumper?
We don't recommend driving with a damaged bumper or lights. It can be unsafe if your vehicle is in another accident.
How to remove a dent from a front bumper?
Depending on the location of the dent on your bumper, you may need to remove the fender liner ahead of the front tire (see above) or a lower aerodynamic valance below the bumper to gain access to the interior of the dent. Both can be unclipped manually.
How to get a dent out of a car?
Use a rubber-tipped dowel or specialty tool (like the one shown in the illustration, readily available online) to push out the dent from the interior until it begins to pop back into its intended shape. You may need to gently work on any small indents with the tool to get a smooth surface. Then replace the fender liner.
How much does it cost to replace bumper covers?
Replacement bumper covers can cost more than $1,000. But dents in the soft plastic bumper covers on cars and SUVs can often be smoothed out at home by applying heat and a little elbow grease. It takes a bit of patience, and certainly experience helps. If you don't have a skilled friend to assist, be sure to watch a couple videos on YouTube for further insights on the techniques needed to get good results.
What happens if you damage a bumper?
Damage that affects the surface, like deep scratches or punctures, will require the services of a body shop. In such cases, the entire bumper cover may need to be replaced and painted, as well as other trim elements replaced and possibly lights moved.
How to make plastic bumpers malleable?
Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don’t apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
How to fix a dented bumper?
When you have access to the area behind the bumper and the dent is a minor one, you will find it can be fixed with the use of a heat gun or hair dryer. Heat guns can reach very high temperatures, so be sure you are wearing heat-resistant gloves, clothes, and eyewear when performing this repair. Direct the hot air from the hair dryer or heat gun at the dented section until it is just warm enough to become pliable. Then, simply reach around to push the dent out from the rear carefully. Leave the area to cool when it is finally back to normal.
How to fix dents in car rim?
For larger dents, a plunger tool will be required. The mouth of the plunger must be firmly attached to the surface to create an airtight seal, which can be improved by applying a little petroleum jelly to the rim. Once the plunger is correctly positioned, it should be held tightly and tugged backward to pull the dent out.
How to clean a dent in a car?
In either case, use a cloth to thoroughly dry the surface after it has been cleaned.
Can you use a bumper repair kit on plastic?
If you noticed any cracks during repair, or if you had to drill a hole to fix the dent, you can use a bumper repair kit to seal it. The kit should contain all the items that you need, but before you buy one, make sure you can use it on whichever type of plastic your bumper is made from.
Can a car accident cause a dent in a plastic bumper?
Anything from a car accident to just backing into a pole can leave a dent in your plastic bumper. An auto body shop can fix it, but why spend hundreds when you can easily do it yourself? By following the steps below, you can remove and repair unsightly dents in your plastic fender, and get your car looking as good as new again.
