
How to Repair a Fiberglass Pool Slide.
- Step 1 – Sand the Surface. Wear a pair of protective gloves and a respirator when working with fiberglass. Using an 80 grit sandpaper, sand down the ...
- Step 2 – Clean the Area.
- Step 3 – Apply the Fiberglass Filler.
- Step 3 – Sand the Repaired Area.
- Step 4 – Apply Gel Coat.
How do you fix a crack in a fiberglass pool?
If you notice a crack in your fiberglass pool, you’ll want to inspect and repair it as soon as possible. The first step is to drain your pool of water so that you have complete access to the crack and surrounding surface area. Depending on the size and depth of the crack, there are different ways to address the issue.
How can I Fix my fiberglass slide?
One side of the slide next to one of the leg sockets is showing some underside separation in the fiberglass, but this should be an easy epoxy filler fix, too. Here's what I rigged up in the mean time for my daughter and her friends to have some fun with (based on an old and unused Little Tyke's play set and a playground slide found on Craigslist).
Can you repair a fiberglass pool slide with Rustoleum?
Fiberglass repair kits are also available, commonly sold for fiberglass boat hull or car panel repairs. Ladder & Legs – For steel legs, (used on the larger pool slides) if rust develops around bolts or flanges, it should be sanded and touched up iwith Rustoleum.
Are cracks in a fiberglass pool dangerous?
Cracks in fiberglass pools range in size and severity – some cracks, like spider cracks, aren’t usually anything to worry about. On the other hand, structural cracks can cause bigger problems if they are not addressed in a timely fashion. If you notice a crack in your fiberglass pool, you’ll want to inspect and repair it as soon as possible.

Can you repair a fiberglass slide?
Fiberglass slide cracks are more common. It can be small stress cracks in the Gelcoat surface, or in rare cases, the fiberglass shell itself can become cracked. Gelcoat repair kits can be purchased, or your slide could be completely recoated, by a local boat repair company.
How do you resurface a fiberglass pool slide?
2:567:20Pool Slide MAKEOVER! How to Paint a Pool Slide. - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet some of the rough. Parts off but multi-surface acrylic builds pretty high and this is gonna be aMoreGet some of the rough. Parts off but multi-surface acrylic builds pretty high and this is gonna be a gloss Sheen.
How do you fix a broken plastic slide?
0:122:55Weld and repair a playground Slide using a plastic welder - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy first job is to clean the damaged area for maximum wall strength. I'm going to use a grinder. AndMoreMy first job is to clean the damaged area for maximum wall strength. I'm going to use a grinder. And a scraper to grind away the oxidization. And the debris. The injectibles has a lot tear.
Can you Epoxy a pool slide?
EP Epoxy Pool Slide Paint According to In The Swim, the only kind of paint that should be used on fiberglass pools is an epoxy pool paint. For fiberglass pool slides, use a product made specifically for this, such as EP Epoxy Pool Paint.
How do I fix a crack in my pool slide?
1:205:30Plastic Pointers #8 - Cracked Inground Pool Slide - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to prep this area through here about two inches on each side of the crack. So that weMoreWe're going to prep this area through here about two inches on each side of the crack. So that we can lay some cloth down for extra reinforcement. All right so we will begin by dropping some plastifix
How do you make a fiberglass slide slippery?
How to Make a Slide Slippery the Safe WayMake a Cleaning Solution. Make a cleaning solution using warm water and a mild dish detergent. ... Scrub Down the Slide. You'll want to use an abrasive rag or hand towel to scrub the slide from top to bottom. ... Let it Dry. ... Wax the Slide Itself. ... Sand the Slide Surface (If Needed)
Can you repair a plastic slide?
If your hole is smaller, cut the patch down to the smallest size that will cover the damage. Using a jig saw, carefully cut the area out of the part where you will insert the patch. To make the strongest repair possible, it is necessary to weld the back side of the patch.
Can you repaint a plastic slide?
Using brush-on paint for plastic can be a good idea if you're painting large areas. The best paint for outdoor and playground plastics is Acrylic-Latex Paint. Regular latex is not durable enough and other non-water based paints like solvent-based paints are much more toxic and more difficult to use.
Do plastic welders work?
As stated, plastic welding can be very strong and durable if done correctly, but a lot of factors will affect its durability, from material to the experience of the welder. Poor or incorrect welding procedure is often to blame for a drop-in durability expectations.
How do I make my rock slide slippery?
0:462:33Q&A: concrete pool slide- best way to make it slicker? - YouTubeYouTubeStart of suggested clipEnd of suggested clipLittle one by one tiles to make them slippery. And then the same thing with that is you could use aMoreLittle one by one tiles to make them slippery. And then the same thing with that is you could use a tile sealer to make it a little bit slick.
What is a swimming pool slide called?
A water slide (also referred to as a flume, or water chute) is a type of slide designed for warm-weather or indoor recreational use at water parks.
Is there a spray epoxy?
Yes, epoxy spray paint is available in an aerosol can for easy use. This offers a convenient way for everyone to touch up paint and finishes around the house. However, using epoxy spray paint can be tricky to get a perfect finish.
How do I make my pool slides slippery again?
1:057:27Polishing Pool Slide With HDSPEED!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet some polish polishing done there and lay some wax behind. So that's what we're going to do thereMoreGet some polish polishing done there and lay some wax behind. So that's what we're going to do there. And I'm going to use a clay bar.
How do you fix a water slide?
Cut a patch that is at least ½ inch bigger than the tear, spread small amounts of glue around the square, and place the patch onto the glue to cover the tear. Then let the glue dry on the patch for at least 24 hours.
How do you make a concrete pool slide slippery?
0:462:33Q&A: concrete pool slide- best way to make it slicker? - YouTubeYouTubeStart of suggested clipEnd of suggested clipLittle one by one tiles to make them slippery. And then the same thing with that is you could use aMoreLittle one by one tiles to make them slippery. And then the same thing with that is you could use a tile sealer to make it a little bit slick. We went from that to the flame on eco finish.
How much does it cost to resurface a fiberglass pool?
The cost to get your fiberglass pool professionally resurfaced is about $6500 , but it depends on the size, shape and age of your pool, as well as the finishes. Luckily for fiberglass pool owners, fiberglass pool surfaces are pretty standard, so the the price of pool repair should be less variable than with materials like gunite, for instance.
How long do fiberglass pools last?
Fiberglass pools are the most low maintenance and if you take care of them properly, they should last decades. They require less than half of the maintenance work required for concrete and vinyl pools because of their gel coat that makes them less porous, so it’s harder for water and chemicals to get absorbed and damage the pool surface.
Why is my pool cracking?
But even with proper maintenance, being exposed to harsh chemicals and other elements can cause havoc to your pool and can lead to cracks and bulges appearing. Follow the steps below to help repair these unsightly blemishes to your pool’s surface.
How to make putty dry faster?
The higher the ratio of catalyst to putty, the quicker the dry time and the harder the putty will dry. Make sure it’s smooth by using a putty knife or scraper to level it. Once it has dried, use the electric sander to smooth the area and wipe it down with some acetone to remove any residual dust.
How to remove peeling paint from crack?
Use an electric sander to sand down the area around the crack or bulge to remove any loose dirt and peeling paint before applying acetone to get rid of any residual dust. Don’t manually sand the area with sandpaper as it won’t produce as smooth a result as an electric sander does.
How far below the water level should you clean a fiberglass pool?
Make sure to collect samples at least 18 inches below the water level on either side of the return jet. When cleaning a fiberglass pool, always ensure you use nylon bristles so that you don’t scratch the surface of the pool and use a pool vacuum that is heavy enough to remove dirt and debris that has sunk to the bottom.
What to do if crack is leaking water?
If the crack is leaking water, first apply hydraulic cement before applying the bond coat.
How long have pool slide construction materials changed?
In the last ten years, pool slide construction materials have changed, and this has led to presumably less maintenance or repair issues.
How much weight can a pool slide hold?
Remember that pool slides have a weight limit of 200-275 lbs. Exceed this limit and the slide could become damaged, or the slider could become injured. For more on safe and intended use of your pool slide, please see the owner’s manual.
What can be left behind on a slide deck?
Ladder treads and the top of the slide deck can catch dust and dirt, held fast by air borne oils and pollutants. Hair products, skin lotion and tanning oil residues can be left behind by users, and your slide could become the occassional target for birds flying overhead.
How to clean a slide with soapy water?
Rinse slide well, then tape a heavy plastic trash bag onto the bottom of the slide, to catch soapy rinse water. Bonus tip – empty the bag before it gets too full!
What can I use to clean aluminum pool ladders?
Often, a quick wipe with a soft clean cloth and some windex is all that’s needed. Use Bon Ami for scale build-up on aluminum.
What to check for on a slide?
Check the slide surfaces for any cracks or chips.
What to use to clean pool shock?
For a deeper cleaning, you can gently use a granulated chlorine powder ( not pool shock !), like Bon Ami or Clorox powder. Be careful not to scrub too hard, and use only a soft cloth.
How much paint do I need for a slide?
For most paints, I'd think at most I'd need somewhere between 1 and 2 quarts of paint to do a couple of coats over that surface area.
What is the SR Smith slide?
The slide seems to be an Aquaslide 'N Dive Queen (there was a "Duke" (three legged) and "Queen" (four legged) version of the slide). It looks like SR Smith might have taken over the Aquaslide company and the Aquaslide 'N Dive Queen evolved into the SR Smith Frontier (or Frontier III) and later evolved into the SR Smith Rogue or Rogue Grand Rapids. Parts kits seem to be available for these slides with a lot of crossover in references to them, with parts ads referring variously to these slides as the Queen, the Duke, the Frontier III and the Rogue. The older the version of the slide, though (like the one I have) the less likely someone like me is to be able to find any complete assortment of parts. And, it's not clear whether the parts for the current SR Smith Rogue will fit the older Aquaslide 'N Dive Queen. I know the water delivery system is different, so the fittings for the water are not the same. However, I do see older water kits that seem like they might be the right ones for the old slide...but it's hard to say.
How long is a crack in a handrail?
None are more than about 1 to 2 inches long, and all look like easy epoxy putty patch-and-sand jobs. This is probably the worst crack, given its location on the exit lip (shown upside down). It's about 2 inches long. Each of the handrail recesses is cracked along one bottom edge (each crack about 2 inches across).
How to remove paint chips from sliding board?
To begin, loosen and remove any peeling or chipped paint from the surface of your sliding board using a putty knife. With all the loose chips removed from your sliding board, you then need to use a sander and 180 or 200 grit sandpaper, sand the entire surface of your sliding board, being sure you sand every nook and cranny.
How long does it take for a sliding board to harden?
When you have coated the entire sliding board, you will need to let it sit to harden for a minimum of 6 hours.
What do you use to apply fiberglass gel coat?
Once you have mixed the fiberglass gel coat, you need to use the felt roller and a paint brush combination to ensure that all surfaces, including the hard to reach ones, are covered in the fresh coat of gel.
What to do if you haven't emptied your pool?
If you have not emptied the swimming pool, it would probably be best to use a sander that vacuums as you sand to prevent the soiling of the water within your pool. When you have completed the task, you need to hand dry the sliding board with a soft towel.
Can a swimming pool slide be faded?
Over time, your swimming pool’s fiberglass slide or sliding board may become faded and worn. Because sliding boards are lightweight, easy to move around and easy to install, they are the most popular choice for most homeowners, but after a period of time, they require maintenance like all other things around your home.
Can you mix ketone peroxide with fiberglass?
When mixing your Methyl ethyl ketone peroxide, a hardener into your fiberglass get coat, it is important to measure correctly using the manufacturer’s directions listed down the side of the container.
What to do if you notice a crack in a fiberglass pool?
If you notice a crack in your fiberglass pool, you’ll want to inspect and repair it as soon as possible. The first step is to drain your pool of water so that you have complete access to the crack and surrounding surface area.
Why is my fiberglass slab cracked?
There are many different things that can cause these cracks to form, including improper installation or manufacturing too thin of slabs that cannot withstand the strain of shipping and lifting . If the fiberglass arrives on-site cracked, it should be sent back and not installed.
What is spider crack?
All in all, spider cracks are just a normal part of wear and tear on fiberglass pools. These hairline cracks form in the surface layer, or gelcoat, and are not structural – which means they will not impact the overall structure of your pool. The crack usually does not extend into the structural laminate layers of your pool, and that’s a good thing.
Can you level a pool with a gel coat?
Ideally, the right manufacturer will create a level pool with the ideal thickness applied to the gel coat to help prevent spider cracks from forming in the first place. In addition, a skilled contractor can properly level the pool and install the fiberglass with care and attention to detail.
Can spider cracks be seen in a fiberglass pool?
Not only are they hard to see, but in addition, they don’t typically cause any problems, so they aren’t usually something to worry about. All in all, spider cracks are just a normal part of wear and tear on fiberglass pools.
What to do if a slide has cracks?
If the slide has cracks or pockmarks, fill them with epoxy-based filler and allow it to dry before sanding the slide. Warnings. Wear protective clothing, gloves, goggles and a respirator for the duration of the project to protect your eyes, lungs and skin from fiberglass dust and fumes from the epoxy. Writer Bio.
How to clean a slide?
Also, remove any chemical contaminants, dirt, oil, grease or salt with a cleaning and prepping solution . As an alternative, clean the slide with a high-pressure washer set at no more than 3,500 psi. Afterward, rinse the slide with clean, fresh water and let it dry completely.
How long does epoxy pool slide paint last?
If applied correctly, EP Epoxy Pool Slide Paint can last up to eight years, according to Asking a Lot. To get started, first remove the slide from its hardware that keeps it held in place. Spread some plastic sheeting or tarp in an open, clean area and lay the slide across two sawhorses on top of the plastic.
Where should a slide be in a pool?
The slide should be positioned away from the primary socializing area so that people won’t have to look at the back of it. Slides generally also work best on the side of a pool rather than an end when the pool is in a residential backyard.
How long does it take for a slide to dry?
Hold the spray can approximately 8 inches away from the slide and spray in a left-to-right sweeping motion. Allow to dry for 12 hours, then turn the slide over and paint the other side.
Can you paint an old pool slide?
Painting an old pool slide will give the pool a lift in appearance. Years of chlorine, sun and use leave slides looking old, scuffed, faded and dull. Excessive wear may render them useless as the original coating wears away and leaves the slide rough, making sliding difficult.
