Repairing Guides

how to repair a ryobi airstrike nailer

by Ms. Pascale Rempel Published 3 years ago Updated 2 years ago
image

Ryobi Brad Nailer 15-Minute Fix [Won’t Shoot Nails]

  • Step 1: Remove the Battery and Nails from the Magazine. Do yourself a favor and be safe by removing the battery from the bottom of the tool first.
  • Step 2: Undo the Locking Clasp and Remove the Two Retaining Screws.
  • Step 3: Remove the Nut and Bolt from Bottom of the Magazine and One on the Side.
  • Step 4: Wiggle the Magazine Free from the Tool.
  • Step 5: Add Oil to the Drive Cylinder.

Part of a video titled [STEP BY STEP] Ryobi P320 Airstrike Fix (not firing nails)
1:29
14:57
So we'll get to that fix here and I'll show you what to do so first things first we're gonna removeMoreSo we'll get to that fix here and I'll show you what to do so first things first we're gonna remove the battery if you have one on there. We're going to empty the magazine of any nails.

Full Answer

Why won’t my Ryobi airstrike Nailer work?

The barrel is another problem and some of the fasteners on the barrel might have gone loose, or some nails can be stuck inside that will cause your Ryobi Airstrike nailer to cease working and that is not something you would like to have for sure.

What batteries does the Ryobi Brad Nailer take?

Best of all, like every RYOBI® 18V ONE+™ blue or green tool, this AirStrike Brad Nailer works with any 18V ONE+™ battery. Upgrade to lithium-ion or LITHIUM+™ batteries for lighter weight and better performance. For increased user control (sequential) or speeds up to 60 nails per minute (contact actuation)

Should I lubricate my Ryobi Brad Nailer?

I kept my Ryobi Brad Nailer in my garage which is not temperature controlled. That means it gets down to -10 Fahrenheit in the winter, and 100 degrees in the summer. Even though I didn’t use the tool much over the 2 years I had it, I never lubricated it and the temperature extremes certainly didn’t do me any favors.

Are Ryobi Tools any good?

The joys of using Ryobi tools is that they are relatively inexpensive, have interchangeable batteries between the tools, and are durable enough for a weekend warrior. Every once in a while though, these tools will give us headaches with malfunctions that stop our work that we planned on tackling.

image

How do you fix a nail gun that won't fire?

My Nailer Won't Fire – Troubleshooting Common Causes of Jams and MisfiresClear Jams. ... Inspect Your Air Supply. ... Reload the Magazine. ... Clean the Tool. ... Replace Seals and O-Rings. ... Inspect for Damage. ... Take It to the Service Center.

How do you lubricate a Ryobi Brad Nailer?

7:3010:25Increase Cordless / Air Nailer Performance - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut you do want to keep them clean and lubricated. With one additional step the little fitting onMoreBut you do want to keep them clean and lubricated. With one additional step the little fitting on the bottom that you're going to plug into the air hose.

How do you get a stuck nail out of a Ryobi nail gun?

1:096:51RYOBI: How to solve problems with cordless and pneumatic nail gunsYouTubeStart of suggested clipEnd of suggested clipOnce open use a flat bladed screwdriver to push the firing mechanism back up into place this willMoreOnce open use a flat bladed screwdriver to push the firing mechanism back up into place this will then give you access to the jamb nail which you may need a pair of pliers to help pull. Out.

How do you fix a nailer?

4:206:10How to Fix a Nail Gun! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell I had the system cranked down to 60 psi I've run wrapped it up to 110 let's see how that works.MoreWell I had the system cranked down to 60 psi I've run wrapped it up to 110 let's see how that works. Well it worked but no nail came out.

Where do you put the oil in a brad nailer?

0:301:30Best Way To Oil Your Nail Gun or Air Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll the tools you want to oil in the inlet. Where your fitting is the amount of oil depends on theMoreAll the tools you want to oil in the inlet. Where your fitting is the amount of oil depends on the tool some tools take just a couple drops like your micro Pender's your Brad nailers.

How often should you oil a pneumatic nailer?

Manufacturers often recommend applying two to three drops of oil at the start of the shift and at lunchtime, at a minimum. One way to detect if your tool is properly lubricated is to check the area around the exhaust. If it is moist, it is adequately lubricated.

How do you remove nail from nail gun?

Step 1: Disconnect the Power Source. Whether your nailer is a pneumatic model that operates with compressed air, or an electric or battery-powered nailer, always disconnect the tool from its power source before beginning. ... Step 2: Open the Barrel. ... Step 3: Remove the Jammed Nail (or Nails) ... Step 4: Reload the Gun, and Test.

Why is my nail gun jamming?

What Caused the Jam: Lack of Adequate Oil: The air cylinder in the nose needs plenty of oil to function properly. Too little oil, and the nails will be slow to feed, causing a jam. Pro Tip: For coil nailers, use 10-15 drops of oil before nailing.

How do you unjam a framing nail gun?

How to unjam a nail gun:Unscrew the two front nose bolts, or lift the nose latch, releasing the front nose plate.Open the nose.Clear the jam and push the driver blade back to its rest position.Close the front nose and refix it.Ensure the work contact element is free.Reinsert the battery and the fuel cell.More items...

How do you service a pneumatic nail gun?

6:277:24Easy nailgun maintenance - YouTubeYouTubeStart of suggested clipEnd of suggested clipEvery couple of minutes months. And run a couple of nails through it. After you put some oil in theMoreEvery couple of minutes months. And run a couple of nails through it. After you put some oil in the back end and you'll make sure that this thing will be ready for you the next time you need.

How do you replace an O-ring on an air nailer?

1:103:52Bostitch Nail Gun Repair - How to Replace the O-Ring - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the bumper comes out of the gun you just place it right back inside with the driver unit removed.MoreIf the bumper comes out of the gun you just place it right back inside with the driver unit removed. Now I can install the new o-ring I'll remove the old o-ring from the piston.

Can nail guns be rebuilt?

You can do the entire job yourself in about two hours and save money in the process. I'll show you how to rebuild a Bostitch framing nailer with a master O-ring kit and a trigger valve assembly. If you have a different brand, don't worry. The rebuild is similar for others.

How do I add oil to my pneumatic nail gun?

0:421:45How to Oil a Framing Nailer - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's different from what goes into your compressor. It's different from what goes in your car. SoMoreIt's different from what goes into your compressor. It's different from what goes in your car. So you want to look for pneumatic tool oil. And there are even two versions of it.

What type of oil do you use in a nail gun?

What kind of oil should I use? Only use lubricating oil made specifically for pneumatic tools, such as Senco Pneumatic Tool Oil or Paslode Lubricating Oil. Other oils lack the correct viscosity or contain ingredients that can destroy the seals, disintegrate O-rings, or may even cause combustion.

Do you need to oil nail gun?

Oiled nailers require regular lubrication to ensure they function properly. Adding a few drops of oil into the air inlet each time you use the tool reduces heat and friction and prevents valves, seals and O-rings from wearing out. During heavy use, you should oil the tool more frequently.

Where do you put the oil in a Paslode nail gun?

3:215:52Cleaning & Maintaining Paslode Cordless Framing Nailers - YouTubeYouTubeStart of suggested clipEnd of suggested clipMay be necessary to repeat this step to remove any heavy deposits or remaining residue with theMoreMay be necessary to repeat this step to remove any heavy deposits or remaining residue with the motor assembly tilt it up squeeze four to five drops of oil into the sleeve.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9