- Check the Siding Panels and Clean the Holes. Check the siding panel for molds, holes or any damage. ...
- Apply Filler Compound. Apply filler compound to the holes in the siding using a putty knife. ...
- Sand the Area. Using a fine grain sandpaper, sand the area where you applied the filler compound. ...
- Paint the Siding. Check the rest of the hardboard siding for paint peelings. Remove the peelings using a scraper. ...
Does your Hardie board siding need cleaning?
GENERAL: It is recommended that hardboard siding be cleaned once per year. This normally would be carried out using a soft brush or sponge along with a mild detergent mixed with water. This cleaning is, in fact, a condition of our warranty and the consequences from dirt and mildew are beyond our control.
How to tell if your home has hardboard siding?
PRESSBOARD SIDING CARE & MAINTENANCE
- Watch for any major flaws. Be on the lookout for any cracked paint, missing sealant, holes, loose nails and other such problems in your hardboard siding that could lead ...
- Slope the ground away from hardboard siding. Make sure that the ground slopes away from the foundation. ...
- Keep nature away from hardboard siding. ...
How to clean your James Hardie siding?
- Always clean and rinse from the top of the siding to the bottom, so that grime gets washed away instead of spread around on the siding.
- Don’t let soap or cleansers dry on the siding. ...
- Regularly rinse out the cloth or sponge as you work, to avoid spreading any grime around on the siding.
How to stain hardiplank siding?
How to Stain Hardiplank Siding
- Finish the board prior to installation. To achieve the appearance of stained wood on Hardiplank, your best bet is to finish the siding before it is installed on ...
- Lay the boards out flat, wood-grained side up. Fiber-cement stain is a product that replicates the look of natural wood by pooling in the imprinted grain pattern on ...
- Dust off the boards. ...
How do you repair Hardie board damage?
To remove and replace damaged siding: Cut the fiber cement siding to length (wear approved dust protection). Blind-nail the fiber cement siding in place, starting with the bottom piece. Face-nail the top piece of fiber cement siding through the old siding. Prime and paint new siding to match the old.
How do you repair Hardie board siding?
8:2814:21How to repair and replace damaged siding: Hardie board, Masonite or ...YouTubeStart of suggested clipEnd of suggested clipGet a nice big caulk. Right there. And then my piece is ready to go again i just do the same processMoreGet a nice big caulk. Right there. And then my piece is ready to go again i just do the same process again this is for keeps this time. So run it up underneath the first board drop it down.
Can hardiplank be patched?
Though it is a tough wearing product, the surface of the siding can sometimes be damaged during installation, by unusual wear or by impact. The James Hardie company, makers of HardiePlank, recommends the use of a cement patch product made of an acrylic mortar compound for patching their siding products.
Can hardiplank siding be repaired?
Repair or Patching Fiber Cement Board Siding Dents, chips, cracks and other minor surface damage in James Hardie siding and trim products can be filled with cementitious patching compound.
How do you repair holes in fiber cement siding?
Use a plastic putty knife to apply the patching material to the damaged area, filling in the area and shaping the patch to match the original contours of the siding. Allow the patch to thoroughly dry and apply another thin layer of patching material if the first layer shrank during the drying process.
How do you fix fiber cement board?
2:1410:26Installing cement board on the wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipReally on the walls I'm only going about four screws four to five screws. Down the stud. You canMoreReally on the walls I'm only going about four screws four to five screws. Down the stud. You can just spread them out we'll talk about this when you get to the floor.
How do you fill holes in Hardie planks?
The installation guide for Hardie Board, which is a brand of cement board siding recommends using caulking to fill nail holes. When I've installed it I used a high-quality exterior paintable calking after smoothing the edge of the holes. Once the caulk is dry you can touch up the paint.
What kind of caulk do you use on Hardie board siding?
Manufacturers' Caulk and Sealant Recommendation Sheet S-100B Caulks and Sealants: James Hardie recommends the use of caulks and sealants that remain permanently flexible.
Why does fiber cement siding crack?
Fiber cement planks are floppy until secured on the wall and holding only in the middle or transporting over a shoulder will cause a dramatic sag at both ends. The stress can cause a crack at the center of a board.
Can Hardie board be sanded?
Yes, you can sand it, in fact you need to do that if you're repairing it.
How often does Hardie board need to be painted?
every ten to twenty yearsHardie Plank is also called fiber cement siding. While it's far heavier than aluminum, vinyl or wood, it is extremely durable and typically only needs a new paint every ten to twenty years for maintenance. It is one of the best materials and long-term solutions for protecting your home.
How do you fill holes in cement board?
Use a carton knife or carbide tip tool to cut the cement board to expose a stud on either side of the damaged area. Use the knife to score and break a new piece of cement board to fit the hole. Attach the new board to the stud using corrosion-resistant screws. Predrill the holes for easier installation.
How do you replace one piece of fiber cement siding?
3:114:42Replacing some pieces of hardboard siding with decent results - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know measure it measure the replacement. Board cutting it with a circular saw just a regularMoreYou know measure it measure the replacement. Board cutting it with a circular saw just a regular blade in here kind of a general purpose blade stuff cuts very very easily.
How do you replace the bottom row of Hardie board siding?
2:0910:22How To Replace Damaged Siding | THE HANDYMAN - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your hammer little rapey from behind your pry bar. You can pry both of them at the same time.MoreTake your hammer little rapey from behind your pry bar. You can pry both of them at the same time. And you don't run out of angle.
Why does fiber cement siding crack?
Fiber cement planks are floppy until secured on the wall and holding only in the middle or transporting over a shoulder will cause a dramatic sag at both ends. The stress can cause a crack at the center of a board.
How do you fill nail holes in Hardie board?
The installation guide for Hardie Board, which is a brand of cement board siding recommends using caulking to fill nail holes. When I've installed it I used a high-quality exterior paintable calking after smoothing the edge of the holes. Once the caulk is dry you can touch up the paint.
Why does my siding rot?
Water from rain or sprinklers can damage hardboard and wood siding over time , causing it to rot or deteriorate. This usually occurs on the bottom rows of siding near the ground, or on siding that adjoins a roof or chimney.
What is fiber cement siding?
Fiber cement is usually blind-nailed, which means the nails go in the top edge of each piece, so the next row above it covers the fasteners. When it’s painted the new siding looks as good as the old, it just lasts a lot longer.
Does new siding last longer?
When it’s painted the new siding looks as good as the old, it just lasts a lot longer.
Can you replace lap siding?
Replacement is the only option for rotted, hardboard lap siding. However, you don’t have to replace it all, just the damaged pieces, which are usually near the ground or adjacent roofing. First, pry the damaged pieces off the wall using a crowbar.
Can you pull down the bottom of a siding board?
As the bottom of each board comes out, you can pull down on one end of it and free it from the nails going through it and the row above. Occasionally there will be nails left behind under the last good row of old siding, which have to be cut or removed so the new siding can go in.
What is a hardie plank?
HardiePlank is a cement lap siding product used on commercial and residential exteriors and is designed for very low maintenance and a long useful life. Though it is a tough wearing product, the surface of the siding can sometimes be damaged during installation, by unusual wear or by impact.
How to get sanding grit off of wood?
Wipe or brush away any of the sanding grit with a clean, dry, lint-free rag or a clean and dry brush, leaving a smooth surface.
Why does fiber cement siding come loose?
There are two main reasons that cause fiber cement siding to come loose, both of which stem from faulty installation of either missing a stud or nailing too high on the pieces. A plank that is nailed too high will start to sag because the thin top lip has started to give.
What to do before making repairs to a wood deck?
Just remember to always eliminate the underlying problem (water damage, rodent infestation, delaminated boards, etc.) before making repairs as you’ll just be running around in circles.
What Goes Wrong With Fiber Cement?
Some industry publishers dub fiber cement as a ‘100 year product’ so there really should be no need to ever have to repair it right? The truth is there is always variables with any home product that could require repair down the line, mostly having to do with faulty installation (gaps, uneven, loose from poor nailing, lack of backer flashing) but could also include rodents, collisions, extreme weather, or water damage to the underlayment.
What is the gap between fiber cement siding joints?
One thing to note about gaps between joints of fiber cement siding is that they are left there on purpose. Although the material expands and contracts less than wood, best installation practices still allow for some movement and to respond to shifts in the home.
How long does fiber cement siding last?
Fiber cement siding is a highly durable product but anything installed 30-40 years on the exterior of a home is going to be vulnerable to damage at some point. Luckily, another versatile benefit of this product is that fixes are usually easy and generally inexpensive.
How to fix a plank that is pulling away from the house?
Planks that have been nailed missing the stud will start to pull away from the house. Either way, the simplest fix is to face nail the boards back into place , this time hitting the stud. If there is no stud available (such as near gable trim) and the plank is curling or rattling, it’s recommended to ‘pin back’ the board by face nailing it 3/4” to 1” from the bottom – strictly for aesthetics and not to increase wind load. Caulk can also be used to secure an angled cut or some other section where a backer is not available.
Can you remove fiber cement boards from a home?
Therefore it's important to know how the product is installed to begin with. Fiber cement lap siding is generally blind-nailed at the top of the plank with the nails being covered by the subsequent row of siding.
