Repairing Guides

how to repair hash board

by Dr. Kaitlyn Medhurst Published 3 years ago Updated 2 years ago
image

How to Repair Antminer L3+ Hash Board?

  1. Thermostat soldering iron at 350-450 degrees Celsius, pointed solder tip for small patches like r-c.
  2. Heat gun for chip disassembly and soldering, no long time heating in case of PCB blistering.
  3. APW3 power source with 12V and 133A Max output to test the hash board.
  4. Multimeter, tweezer, L3+ hash board tester (oscilloscope preferred).

More items...

Full Answer

What should I do if my hashboard is damaged?

Investigate hashboard for obvious failures (burns, swollen chips, etc) and set board aside if found. Blow excess dust from hashboard with Data-Vac. Spray alcohol between hashboard heatsinks, allow alcohol run-off into a bin for later disposal.

What tools do you use to test the hash board?

Skilled mastery. 2. The hot air cylinder is used for chip disassembly and soldering. Be careful not to heat it for a long time to avoid PCB foaming. 3. DC stabilized power supply (output 12V, 20A), used for the test and measurement of the hash board. 4. Fluke 15b+ multimeter, tweezers, Debug, G7 maintenance special control board, oscilloscope . 5.

How do I know if my Hash board is good quality?

• The repaired hash board can be determined to be a good product if it passes the fixture tests for more than twice.

What does it mean when the hash board does not run?

5. Not running: No running means that the test box cannot detect the chip information of the hash board, but displays NO hash board; this phenomenon is the most common and the fault range involved is also wide.

image

How do you solder ASIC chips?

5:1036:27Replace ASIC chip on T17 hashboard Part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipSome chips take about 30 seconds to take off some take 40. Some take 70 or 80..MoreSome chips take about 30 seconds to take off some take 40. Some take 70 or 80..

How do you clean ASIC Hashboards?

The best way to clean an ASIC bitcoin miner is to use a high pressure air compressor with air gun in interval bursts. This will blow out the accumulated dust from the chassis, hash boards, and fan blades.

What is Hashboard?

​ It is an aluminium box with two fans that contains a controler and between one and three computing cards called "hashboards"

How do you disassemble an Antminer s17+?

2:373:17ASIC Miner Antminer S17 Tear Down Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd that is how you take apart an ant minor. Basic. And minor s17. If you have any questions leave aMoreAnd that is how you take apart an ant minor. Basic. And minor s17. If you have any questions leave a comment down below thanks for watching.

How do you clean a crypto miner?

4:546:04How to Clean a Bitcoin Miner - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you really want to get it clean you're going to have to use alcohol.MoreIf you really want to get it clean you're going to have to use alcohol.

How do you maintain an Antminer?

Antminer Operation and Maintenance ManualHashrate check. (1) Check the hashrate of the miner every two hours. ... Power Check. ... Network inspection. ... Temperature and humidity check. ... Environmental inspection. ... Visual inspection. ... Notes on Installation. ... Notes on disassembly of the miner.

How do you use a Hashboard?

Start operation: write dataInsert the data cable into the hash board that needs to write data.Select (eerpom设定) on the device and click the "OK" button.Select (打开eerpom) and click the "OK" button.Find the data file you just saved and click the "OK" button to confirm.More items...•

Why do you need to be familiar with chip soldering?

2. You must be familiar with chip soldering to avoid blistering and deformation of the PCB or damage to the pins.

How to tell if a signal chain is broken?

For example, a chip itself can work, but it will not forward other chip information; at this time, the entire signal chain will come to an abrupt end, and lose a large part of it, which is called broken chain. Generally the broken chain can be displayed by the test box. For example, when the test box detects the chips, only 14 chips are detected. If the number of preset chips is not detected in the test box, it will not run, so it will only display how many chips are detected, at this time, according to the displayed number "14", the problem can be found by detecting the voltage and impedance of each test point before and after the 14th chip.

How many crystal oscillators are in the T1558?

2. The T1558 clock is two 12M crystal oscillators, which are transmitted in series from the first chip to the 30th, and 31 to the last chip.

What does the black number on a chip mean?

2. The black numbers represent the order and bit number of the chip.

Can you use debug connection for chip detection?

2. After the routine detection is no problem (generally, the short‑circuit detection of the routine detection is necessary, so as not to burn the chip or other materials due to the short circuit when the power is turned on), you can Use DEBUG connection for chip detection, and judge and locate according to the detection result.

How to clean hashboards with alcohol?

Blow excess dust from hashboard with Data-Vac. Spray alcohol between hashboard heatsinks, allow alcohol run-off into a bin for later disposal. Brush between heatsinks with horsehair brush, careful not to damage bristles against hashboard heatsinks. Spray again with alcohol.

How to save a hashboard image?

Go to the top menu "File" -> "Export" -> "Hex" and save the hashboard image.

What brush to use to clean chips?

Brush chips with horsehair brush, clean brush if it gets dirty.

Can I reinstall ASICseer?

Reinstall ASICseer on those ASICs using the Multi-ASIC Installer.

Why does my cryptocurrency chip break?

This is one of the most common breakdowns, since all the work of mining the cryptocurrencies directly falls on the chips, which leads to breakdowns. This could be a power distribution problem, a problem with the first or last chip, or a problem requiring complete chip reflow.

How long does it take to replace RAM in a 5G machine?

We replace 24 RAM modules in your machine to make it a 5G machine! Aprox wait time: 30-60 days

How long does it take to fix APW3+?

We fix your APW3+ PSU! Aprox wait time: 30-60 days

Does a hashboard start working if it finds chips?

Unfortunately even if your machine finds some of the chips, the hashboard will only start working if each of the chips on the board is functional . One or more chips may need replacement to cover your lost hashrate.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9