- 1: When a puncture happens, the first step is getting an inflatable SUP repair kit. Repair kits typically includes PVC patches and PVC glue.
- Step #2: Next, you need to find the hole. One of the best ways to do this is by pumping the board with air and then wiping it down with ...
- Step #3: Clean the patch and area around the puncture. Once the area is clean, mark it with a pen or permanent marker to avoid losing it later on.
- Step #4: Now deflate your board as this will make it easier to glue on the patch.
- Step #5: Apply the PPV patch. It should be enough to cover the hole. ...
- Step #6: Then, trace the outline of the patch. Outlining the patch will allow you to make sure it’s centred and that you don’t use too much glue.
- Step #7: Apply a thin layer of glue to the patch and board. Evenly spread the adhesive. ...
- Step #8: Once the glue has been applied three times, wait five minutes and then press the patch to the area. ...
- Step #9: Remove any extra glue with the acetone wipe. Wait at least 24 hours before re-inflating your board.
- Step #10: Pump up your board and test using the soap and water approach outlined in step #2. ...
Can an inflatable paddle board be repaired?
At least temporarily or in case of need, you can also repair your inflatable paddle board yourself. Most boards come with repair kits. With this repair kit and my instructions, your board can be repaired relatively easily by yourself. My guide here I not a solution for the fastest possible repair. Take your time and follow all steps properly.
How do you fix a paddle board that won’t stand up?
The PVC Stitch solution forms a patch that’s flexible, strong, and completely water resistant. Many seasoned paddle boarders won’t hit the water without some of these repair kit essentials. For minor dings, you can use a quick-curing epoxy product such as Solarez UV Cure Epoxy Ding Resin to smooth out your board for a clean finish.
How do you fix a leaking inflatable sup?
These types of boards are typically repaired using a liquid resin which fills in holes and hardens when it dries. The first thing you want to do when trying to fix a leaking inflatable SUP is to find the hole.
How do you fix an air leak on a paddle board?
Use the pencil to mark the location of the leak and let the air out of the paddle board. Lay out the cover so that the area around the leak is as flat and wrinkle-free as possible on the substrate. Clean the plane around the marked leak with acetone and a clean rag.
How do you fix a seam on an inflatable paddle board?
0:071:52Repairing a seam leak in your board. Part 1. - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing you want to do is clean it and I using the methyl ethyl ketone here. Which is a greatMoreFirst thing you want to do is clean it and I using the methyl ethyl ketone here. Which is a great solvent. Please use caution this is available in Home Depot and Lowe's a taste hardware.
How do you fix an inflatable paddle board valve?
1:072:21How To Fix a Leaky Stand Up Paddleboard Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt when it's inflated but it's not going to get as tight as it could if you tighten it while it'sMoreIt when it's inflated but it's not going to get as tight as it could if you tighten it while it's uninflated. So basically what you need to do is take one hand and hold underneath.
How do you fix a popped paddle board?
1:363:37How To: Patch an Inflatable SUP Board - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the patch laid down roll out the patch using pearl roller or roller rasp in at least fourMoreWith the patch laid down roll out the patch using pearl roller or roller rasp in at least four different directions. This will match the glue together and help remove any air bubbles.
What glue do you use to fix a paddle board?
For boards made of PVC or urethane-coated material, Clifton Urethane Adhesive is a great glue for applying a patch.
Can inflatable paddle boards be repaired?
2:093:55How To Repair An Inflatable Paddle Board Puncture - YouTubeYouTubeStart of suggested clipEnd of suggested clipKits is not a two component glue. So you do not need to mix it with something else before using itMoreKits is not a two component glue. So you do not need to mix it with something else before using it you can just open it and apply it. Straight on the area where you're going to do the repair.
Can paddle boards be repaired?
To repair the ding yourself, we highly recommend using Solarez for SUP as your paddle board repair kit. It's basically a tube of resin that you squeeze into a hole in your board that will solidify when exposed to UV. Its a super easy and quick fix.
How do you repair an inflatable seam?
2:013:55Invisible Seam Repair on an Inflatable Toy - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround i push the vinyl of the toy down against the glue covered patch this squeezes out some of theMoreAround i push the vinyl of the toy down against the glue covered patch this squeezes out some of the vinyl cement. So i quickly reach for the paper towel to dab away the excess.
What is in a SUP repair kit?
The SUP repair kit includes SUP deck pad repair patches, a wrench and SUP repair glue. The 2-piece strong and durable PVC patches provided in the inflatable paddleboard repair kit are perfect for inflatable SUP seam repair. The wrench is ideal for replacing or repairing the air valve.
Do inflatable paddle boards lose air?
LEAVING THE BOARD INFLATED All inflatable paddle boards will lose some air pressure over time if the board is left inflated day after day. Therefore before taking the board out again it would be wise to quickly check the air pressure with the gauge on your pump as you may need to top it up.
Can you use Gorilla Glue on a paddle board?
Gorilla glue foams up when it's mixed with water, and so it is great for glueing together busted boards (it what I used on Boyums board and my 19' Speedboard) but it sands like soft plastic.
What is Stormsure glue?
Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong.
What are inflatable paddle boards made of?
Inflatable paddle boards are made by “drop stitching” 2 layers of polyester fabric together with thousands of polyester threads. Then an air-tight coating goes over the outside surfaces of both sides of the material. The SUP sidewall material is made of polyester fabric that's coated on both sides.
How long to wait to clean a patch on a board?
The next step is to clean the patch and marked area of the board with MEK very thoroughly. To do this, you’re going to clean it once, wait 5 minutes, clean it a second time, wait 5 minutes, and then clean it a third time. Now you’re ready to apply the glue with which you’re going to be apply 3 coats.
What to do if your board is losing air?
If your board is losing air, the first thing you should do is take the included valve wrench in your repair kit and tighten down your valve. The valve sits inside of a seat and when you tighten it with the valve wrench, this makes sure it’s properly seated and that no air is leaking from around the valve.
How long to wait to apply glue to a board?
Apply a thin layer to both the patch and the marked area on the board, spreading it around evenly with the brush. Wait 5 minutes and repeat, then wait another 5 minutes and repeat again.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later.
How to repair a crack in a paddle board?
How to: Let the paddle board dry completely. Sand and clean the crack and the area around it then wipe it dry. Apply epoxy over the crack and around it using a brush. Allow it to dry for a few minutes. Use a different brush to apply a second layer of epoxy over the crack.
How long does it take to repair an epoxy paddleboard?
The process may be a little complicated if the hole or crack is huge on your epoxy paddleboard. But with the right kit, you can fix it in a few hours —as long as you follow the instructions carefully. Inflatable paddleboards are even easier to repair. And the required materials are readily available too.
Can you fix a crack in an epoxy paddleboard?
You can fix most cracks and dings at home. Even instances in which you can see the foam core (for epoxy paddleboards). If the hole is too big and the following solutions won’t cut it, go to a professional. Let them advise you on what to do. Also, before you go through the trouble, check whether it is a cosmetic issue.
Do SUP boards come with a repair kit?
There is a reason why some SUP boards come with a repair kit. As a paddle board owner, you have to be prepared to deal with minor damages. You will encounter them sooner or later, regardless of how careful you are. When it first happens, you can take the SUP board to a shop. But at some point, you have to learn how to do it yourself.
How to fix a bump on a SUP?
Apply and Seal the Patch. Now that you’ve put enough glue onto the patch and surface of your SUP, press it firmly onto your board to get rid of any bumps, ridges, and general uneven spots. Once you have it stuck on nice and solid, clean off the whole space and get rid of any glue remnants you may have.
How to patch a board with glue?
Take the brush that you have in your repair kit, put a bit of glue on it, and gently apply it to the patch as well as the exterior of your board, where you want to stick the patch over. Try starting in the middle of the patch and working your way out to the edges.
Is an inflatable paddle board more durable than a rigid paddle board?
If you have an inflatable paddle board then you know how convenient it is. There is no need to worry about where to put it or hassle with tying it up to your vehicle whenever you head out to the water. While overall inflatable boards are more durable than rigid paddle boards, you do run the risk of it getting a rip or leak in it.
Where is Shayanne Weeks?
Shayanne Weeks. Shayanne is a freelance writer and marketer based in LA, California. Describing herself as a nomad, she has lived in Boise, Idaho and Seattle, Washington as well as Guadalajara, Mexico. As an extremely active person, she loves to snowboard, skateboard, and ski.
Can you use urethane adhesive on PVC?
If you have a board with PVC or urethane-coated material, there are also some excellent urethane adhesives out there that can be used to apply a patch with. As occasional damage comes in the form of a coating abrasion, you’ll simply paint on a layer of said adhesive. As it’s not a puncture, a patch isn’t really necessary.
What type of board do I need to repair?
Types of Board Material. The two common types of boards you’re likely to attempt a repair on are inflatable and hard boards. Inflatable boards are filled with air and are susceptible to getting punctures that require a patch to fix. Hard boards are similar in material to traditional surf boards and are comprised of a fiberglass-reinforced plastic ...
How long does it take for glue to dry on a board?
Wait for the glue to dry for five to seven minutes and then apply the patch to the board. Use the edge of a blunt object with a smooth surface to press out the air bubbles from underneath the patch. Let it dry for about a day before re-inflating the board.
What to do if you have gouges in your board?
If you have large gouges or missing pieces in your board, it’s better to seek the help of a professional or just cut your losses and buy a new board. But if you have only minor repairs to do on your board, there are a number of products available that will make repairing your board a simple task.
How to fix a leaking inflatable SUP?
First you can pump the board and wipe the outside with a sponge and soap, attempting to find where the bubbles are forming as you move across the surface.
Can hard board get dings?
With extended use your hard board will eventually get dings and other damage. The more severe damage can penetrate the outer shell of the board and expose the inner foam. Failure to repair the board when this happens can result in water getting inside and potentially ruining an otherwise salvageable board.
