
- Unplug your mop and let it cool down
- Empty up your water tank
- See if the spray tip of your shark steam mop is blocked
- Insert a paperclip into your mop’s spray tip and move it back and forth. This will loosen debris.
- Pour some white vinegar onto the mop head. Then rub it with a duster or rag. This will clear up further buildup in the mop head area.
- Turn it on and try to use it as usual.
How do you unclog a shark steam mop?
- Make a solution with 50% vinegar with 50% water.
- Put it inside the water tank of your shark steam mop
- Let the solution sit overnight. Some people call it marinating.
- In the morning, plug it in and hold it over your sink.
- Set the steam setting at the highest.
- Get ready for a loud burst of steam and sediments.
How to unclog steam mop?
How to Unclog Steam Mops. Unplug your steam mop and let it cool completely. Locate the spray tip at the base of the steam mop. Insert a paperclip into the spray tip opening to remove any possible clog. Pour vinegar through the mop head to clear any clogs located there. Click to see full answer.
How to fix it- shark steam mop not steaming?
- Unplug your mop and let it cool down
- Empty up your water tank
- See if the spray tip of your shark steam mop is blocked
- Insert a paperclip into your mop’s spray tip and move it back and forth. This will loosen debris.
- Pour some white vinegar onto the mop head. Then rub it with a duster or rag. ...
- Turn it on and try to use it as usual.
How to fix a broken shark steam mop handle?
How to Fix It?
- Fill the tank with water
- Check your mop’s bottom cap tightness
- See if it’s secured in place
- If you see a problem, then call up your manufacturer
- If possible, fix it. If not, replace it.

How do you fix a Shark steam mop that won't release steam?
Unplug the Shark and remove its head. You'll spot a small hole -- this is the nozzle from which the mop releases steam. Simply insert the end of your cleaner or paper clip into the hole and gently move it up and down a few times to clear away steam-stopping buildup.
Why has my steam mop stopped steaming?
A common cause to your cleaner not producing steam can be a failed heating element. As the heater is used to heat up the water, if that has ruptured or burnt out your steam cleaner will not produce any steam. With the water tank filled and switched on the steamer should sound like a boiling kettle.
How do you disassemble a Shark steam mop?
1:163:25How to Disassemble and Repair a Shark Steam Mop - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou don't want to lose any screws just going to go ahead and take this and dump it up lay down bunchMoreYou don't want to lose any screws just going to go ahead and take this and dump it up lay down bunch of them should fall. Out. Take the clamp. Off. Alright at this point. It should pull apart.
Why is the blue light flashing on my Shark steam mop?
Not Plugged In Check to insure that the steam mop is plugged into a working outlet. You will notice a blinking blue light on the front of the device when plugged in correctly. If the light fails to come on then try to plug into a different outlet.
How do you fix a steamer that won't steam?
No Steam or Loss of Steam If the steamer runs out of the water, then steam will not produce. If you've been using the steamer consistently, the flow of steam will decrease until there is nothing left. All you have to do is refill the steamer with more water and this should rectify your problem.
How do you unclog a steam mop?
1:132:14Unclog steam mop easy fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use any wire. It's small enough and diameter OD I just put it in a hole right there. AndMoreYou can use any wire. It's small enough and diameter OD I just put it in a hole right there. And shoved it in nice and gently.
Can you use vinegar in Shark steam mop?
To prolong the life of your steam mop, we recommend using distilled water in the tank. Make sure you only add water to the tank – chemicals or cleaning solutions (including vinegar) may damage the steam mop and could be unsafe. For best results, sweep or vacuum your floors prior to cleaning with your steam mop.
How do you remove the handle from a Shark genius steam mop?
Press the Release button on the back of the Steam Mop body, and both sides of the Genius Mop Head will drop open, releasing the pad. Once the pad has been released, close the Genius Mop Head.
Why is the light flashing on my Shark?
The blue light on your Shark vacuum flashes to let you know that the charging process is ongoing. However, it's not a sign of a problem, so you have nothing to worry about. The light will dim slightly but stay on instead of flashing when the battery is full.
Why is my Shark battery flashing while charging?
From the manual: • Top and bottom LED lights are flashing: Battery temperature is not optimal, so charging is temporarily paused. Leave battery plugged in and charging will resume soon. Sorry, there was a problem. Please try again later.
Do I need to descale my Shark steam mop?
DECALCIFYING YOUR STEAM MOP Calcium and mineral deposits can build up and impact the performance of your steam mop over time. To extend the life of your product we recommend that you use distilled water or Shark®'s Water Filtration Bottle. Visit www.SharkClean.com to order.
Can I put vinegar in my steam mop?
Floor steam cleaning mops use steam to clean hardwood, tile and linoleum flooring. Usually, you mix a small amount of soap with water and pour it into the mop. This provides adequate cleaning. However, you can add vinegar to the mixture and enhance the cleaning power of the mop.
How do I clean my steamer without vinegar?
If your steamer has a hose attachment, you should clean that, too. Simply detach the hose and flush it with water. You can do this outside with a garden hose, or carefully in the kitchen sink or shower. Flush the hose several times, or until the water runs clear once it filters out of the hose attachment.
What kind of water does Shark use?
While fresh tap water does the trick, Shark recommends using distilled water to prevent steam-inhibiting calcification. At its website, the company also offers its Water Filtration Bottle, which filters hard water for use in your steam mop.
Does Shark Steam Mop have steam?
Before you panic, make sure your Shark Steam Mop's reservoir is filled with clean water -- no water means no steam. Once you've filled the tank to the fill line, give your mop about 30 seconds to heat up and produce steam before moving on to other troubleshooting procedures.
How to clean shark steam mop head?
See if the spray tip of your shark steam mop is blocked. Insert a paperclip into your mop’s spray tip and move it back and forth. This will loosen debris. Pour some white vinegar onto the mop head. Then rub it with a duster or rag. This will clear up further buildup in the mop head area.
How to make a shark steam mop?
Here are the six steps-. Make a solution with 50% vinegar with 50% water. Put it inside the water tank of your shark steam mop. Let the solution sit overnight. Some people call it marinating. In the morning, plug it in and hold it over your sink. Set the steam setting at the highest.
Why isn't my shark steam mop working?
Some other reasons might sound ridiculous, but they actually happen. One reason might be that you have no water in your mop tank. Another might be, your water isn’t fully heated. People tend to overlook the recommended level of water intake.
Why is my shark steam mop not steaming?
Well, the most common reasons for this are blockage and pressure leakage. And the most common solution to blockage is to put vinegar in the tank for a night .
What happens if you keep your mop plugged in?
If the steam doesn’t come out and you keep it plugged in, then you might face blast. Steam expands with more heat. With this expansion, steam creates more pressure on the mop wall. Once the steam becomes super pressurized, the probability of mop wall crack increases.
Why won't my mop release steam?
The mop releases steam due to pressure. If this pressure gets cut off or leaked somewhere, then steam won’t get released through the mop head. This might happen due to several reasons. One of those is a poorly filled bottom cap. Because of this, your mop might not produce any steam at all.
What happens when you boil water in a steam mop?
Simply put, normal water contains hydrogen, oxygen and other minerals in it. When you boil it, the water becomes vapor and the minerals stay as remainder.
Tools
These are some common tools used to work on this device. You might not need every tool for every procedure.
Troubleshooting
If you are having issues with the Shark Pro Steam Pocket Mop, please refer to the trouble shooting guide.
Background and Identification
The Shark Pro Steam Pocket Mop was released in 2010. This model of the Shark Pocket Mop is identified by a silver plate on the front with shark emblem in the middle. The device model number S3601 is located on the back of the device under the water reservoir tank. The silver plating on the front of the device differentiates it from the other mops.
