Here’s how to repair a shower diverter in seven simple steps:
- Turn off the water supply to your shower.
- Seal off your drain with tape so that small screws or other important parts are not lost down the drainpipe.
- Tighten the screws behind the faceplate of the diverter valve. If you attempt this fix but the water continues to pour or leak slowly from the bathtub spout after the ...
- Disassemble the shower diverter. If your diverter has a rotating valve, unscrew the nut at the stem of the diverter and remove the entire valve. ...
- Replace the diverter. To be sure you purchase the correct replacement, bring your old diverter with you to the store.
- Install the new diverter, making sure that the parts do not cross-thread each other. Use a wrench to tighten the diverter, being cautious not to overtighten it. ...
- Turn the water supply back on. Engage the shower diverter, directing the water flow to the showerhead. ...
How to fix the diverter in your shower?
What Is a Shower Diverter?
- Step One: Prepping Your Area. First things first, you’re going to want to clear the area and make sure you are adequately prepared to fix your diverter.
- Step Two: Accessing the issue. ...
- Step Three: Removing Your Shower Faucet/Handle. ...
- Step Four: Lubricate Your Shower Diverter. ...
- Step Five: Correct Any Leaks. ...
How to repair a Moen Mixing valve for a shower?
Using the pliers, grab on to the mixing valve. Move it gently from side to side to loosen it. You can then pull the valve cartridge out. Check the valve for any visible signs of wear or cracks. Use a brush to remove dirt and get a better look at the valve.
How to install rough in valve for shower?
Tools For The Job
- Prepare Your Moen Shower Valve. Some prep work needs to be done to the Moen shower valve. ...
- Insert The Valve Into the Wall. Since this is a rough-in, your wall should already be open. ...
- Secure The Joints. This step is vital but can also be dangerous. ...
- Re-Insert The Cartridge. ...
- Install The Shower Valve Handle. ...
How to repair single mixer valve shower valves?
K-8304 Identifying Characteristics:
- Black mixer cap has 4 screws located in a square pattern that screw the cap to the brass valve body.
- Features an orange temperature limit stop attached to stem of the mixer cap.
- The brass, round, splined stem rotates clockwise to turn on.
How do I fix my shower diverter valve?
How to Repair a Shower DiverterTurn off the water supply to your shower.Seal off your drain with tape so that small screws or other important parts are not lost down the drainpipe.Tighten the screws behind the faceplate of the diverter valve. ... Disassemble the shower diverter. ... Replace the diverter.More items...•
How do you replace a shower water diverter?
0:155:20How to replace a spout diverter if your shower pull stopped workingYouTubeStart of suggested clipEnd of suggested clipAnd then turn it counterclockwise while pulling away from the shadow wall continue to turnMoreAnd then turn it counterclockwise while pulling away from the shadow wall continue to turn counterclockwise until the spout is completely removed. You may need to remove the plumber's tape.
Do I need to turn the water off to change a shower diverter?
If you're only working on the diverter, you don't need to turn off the water supply to the faucet. While working, place a cloth over the tub drain to prevent any dropped screws from going down the drain. Some showers use a diverter built into the tub spout activated by lifting a button on the spout.
How do you fix a shower diverter that won't stay up?
0:041:17Shower Repair : How Do I Repair the Diverter in a Shower? - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat you'll take your new one once you get the new one it slides into place use that same allenMoreThat you'll take your new one once you get the new one it slides into place use that same allen wrench lock that screw back in place now on a three handle tub and shower valve.
Can you fix a diverter valve?
Diverter valves can become damaged or stuck. This is because they're a moving part and can be oscillating between being open or closed many times a day. However, they are fixable.
How much does it cost to replace a shower diverter valve?
Replacing a shower diverter valve costs $225 to $575, including materials and labor. A shower diverter valve switches the flow of water between the bathtub spout or shower head and is typically controlled by a small handle located on the center trim plate or near the tub spout.
How long does it take to change a diverter valve?
You should call a gas safe registered engineer if you need to replace the diverter valve or service the working parts of the valve after you've diagnosed the problem. It shouldn't take more than an hour for this to be done on a boiler under eight years old, as parts should be readily available.
How do you clean a shower diverter pull up?
0:142:25“cleaning” a bath tub DIVERTER VALVE so it works again - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition where it diverts the water up to the shower to remove this diverter you want to spin. OffMorePosition where it diverts the water up to the shower to remove this diverter you want to spin. Off the little knob.
Are all shower diverters the same?
There are three different types of shower diverters: After you find the right combination of hot and cold water, you turn the third handle clockwise to send the water to the showerhead. When you're done showering, turn the handle counter-clockwise to redirect the water to the tub.
How long does it take to change a diverter valve?
You should call a gas safe registered engineer if you need to replace the diverter valve or service the working parts of the valve after you've diagnosed the problem. It shouldn't take more than an hour for this to be done on a boiler under eight years old, as parts should be readily available.