- Unplug the washer or disconnect power.
- Remove the lower kick panel.
- Locate Door Lock Unit Reach up along the inside of the front and locate the bottom of the door switch/lock unit.
- Find Teardrop-shaped Tab Located on the bottom of the door switch/lock unit is a teardrop-shaped tab. Gently pull the tab down about a 1/4-inch or until a click is heard. ...
How do you reset a whirlpool duet washer?
How do you reset a whirlpool duet washer? Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
How to unlock a whirlpool duet washing machine?
To do so, follow the steps below:
- Power-off Whirlpool Duet front loader washer for a minute or two before opening the door.
- Pull Whirlpool Duet front loader washer away from the wall.
- Reach behind Whirlpool Duet front loader and feel for two latches on either side of the door hinge.
- Lift latches to open Whirlpool Duet front loader washer door manually.
Why will my Whirlpool duet dryer not start?
Why will my Whirlpool Duet dryer not start?
- Inspect household fuses or breakers.
- Close the dryer door firmly.
- Press and hold the "Start" button for five seconds.
- Check the display on the dryer for error codes.
- Press the "Start" button and hold for several seconds to restart the dryer if "PF" appears on the display.
How to fix F06 on a whirlpool duet?
- Push the pause button twice to get rid of the f06 error message.
- Unplug the power cord and wait for a couple of minutes.
- Stop the water flow to the washer.
- Replug the power cord and press the start button to initiate a new wash cycle.
- Again, press the pause button twice if the f06 error message is persistent.
What are the most common problems on a Whirlpool washing machine?
Here are seven of the most common problems on a Whirlpool washing machine and potential fixes for them.Washer Making Unusual Noises. ... Washer Won't Start. ... Washer Lid Won't Lock. ... LD Error Code Appears. ... Washer Leaves Deposits on Dark Clothes. ... Washer Has a Burned Plastic Odor. ... Rust Spots Appear on Washer Lid.
How do you fix a Whirlpool Duet washer that won't drain?
4:209:06DIY washer wont drain - repair whirlpool duet - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's pretty simple and then it has two screws. It's got one here and it has a sister screw on theMoreIt's pretty simple and then it has two screws. It's got one here and it has a sister screw on the other side that's the exact same one and remove those two screws real. Quick.
Is there a reset button on a Whirlpool Duet washer?
Steps to Reset a Whirlpool Washing Machine Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.
How do you take apart a Whirlpool Duet washer?
0:184:55Whirlpool Duet/Kenmore HE3 Front-Load Washer DisassemblyYouTubeStart of suggested clipEnd of suggested clipAnd lift the panel off the removal of the front panels is more involved first remove the front lowerMoreAnd lift the panel off the removal of the front panels is more involved first remove the front lower access panel by uninstalling the mounting screws.
What causes a Whirlpool washer not to drain or spin?
If your washer won't drain or spin, the water level control may be faulty. Open the machine's control panel and look for a plastic tube attached to the water level valve. If it's clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
How do I force my Whirlpool washer to drain?
Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load. Check the washer's discharge hose if the water fails to drain from the washtub.
How do I reset the sensor on my Whirlpool washing machine?
0:203:46How to Do a Whirlpool Washer Reset & Recalibration - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo first rotate your washer's control dial counterclockwise. Until it's at the north or 12 o'clock.MoreSo first rotate your washer's control dial counterclockwise. Until it's at the north or 12 o'clock. Position. Once that's done unplug the washing machine from the wall.
How do I reset my Whirlpool Duet Sport front load washer?
2:307:39WHIRLPOOL FRONT LOADER - Easy RESET - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo usually when there's a drain problem um the door will remain locked. And uh the only way you canMoreSo usually when there's a drain problem um the door will remain locked. And uh the only way you can really get in there is if you override. It by taking the top off. And you can see that white thing
How do I troubleshoot my Whirlpool washer?
While troubleshooting a Whirlpool top load washer, check the washer tub's agitator by turning on the washer, opening the lid and seeing if it moves. Remove a faulty agitator and inspect for damage. Replace damaged components with parts from an agitator repair kit. If the washer has a belt drive, inspect the drive belt.
How do you take a Whirlpool front load washer apart?
3:3010:55Whirlpool Front-Load Washer Disassembly, Repair ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a t20 Torx bit to unthread the screws in the dispenser. Housing. Next cut the control panelMoreUse a t20 Torx bit to unthread the screws in the dispenser. Housing. Next cut the control panel housing mounting. Screws. You can now lift up the task to detach the housing.
How do you get to the drain pump on a Whirlpool Duet washer?
Pull the bottom of the access panel toward you and pull it down to release it from the washer. The drain pump is under the Duet washer drum and has two hoses.
How do you fix a Whirlpool washer that won't spin?
14:1119:41Whirlpool Washer Won't Spin - How to Test and Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd keeps falling out you'll need to purchase a new shift actuator of a slightly different model andMoreAnd keeps falling out you'll need to purchase a new shift actuator of a slightly different model and i'll have the part number in the description.
Why is my Whirlpool front load washer not draining?
The drain hose may be too far down inside the drainpipe (standpipe) or laundry tub. Drained water can siphon back into the washer if the drain hose extends too far. Make sure that the drain hose does not extend more than 4.5" (113 mm) into the drainpipe or laundry tub.
Where is the drain pump on a Whirlpool front load washer?
0:373:33Whirlpool Front-Load Washer Replace Drain Pump #WPW10425238YouTubeStart of suggested clipEnd of suggested clipSlide the panel to the right to fully detach disconnect the drain pump wire connector. Use pliers toMoreSlide the panel to the right to fully detach disconnect the drain pump wire connector. Use pliers to release the clamps securing the drain hose to the pump and pull the hose. Off.
Does the Whirlpool Duet washer have a filter?
The filter on a Whirlpool Duet is located under the front kick plate. A washer filter collects lint that falls from clothes during the washing process. The lint filter should be cleaned at least once every 6 months. If the lint is not removed, it can cycle back through the washing machine and stick to laundry.
How to skip duet washer?
You can skip trough the Duet washers quick test functions by pressing the Start button. (All except C00 (Door Lock) and C03 (Dispensing System))
Why is my duet washer not draining?
Or perhaps your Duet washer wants a beer… This can be caused by using non HE washer detergent, using too much soap, or possibly a drain pump or pressure sensing problem.
How many tries does it take for a duet washer to unlock?
Your Duet washer was not able to unlock after six tries. Check that the tab on the washer’s door that inserts into the door lock is not broken, that it’s properly aligned with the door lock hole, and that there is nothing that may be jamming the lock.
What direction does the drum rotate on a C06 duet washer?
C06 Duet Washer’s drum continues to rotate clockwise, and the heater is turned back on. IF more water needed to reach the minimum water level for wash the valve will open.
How many times can you lock a duet washer?
Your Duet washer was not able to lock the door after 6 times… you can’t say it didn’t try. Check that the tab on the washer’s door that inserts into the door lock is not broken, that it’s properly aligned with the door lock hole, and that there is nothing that may be jamming the lock.
What does 888 mean on a duet washer?
If you got into the Duet washer’s diagnostics, all the control lights will turn on and “888” will be displayed showing you all the time display lights are working. After a few seconds, all the washer’s display lights will flash. If there are any saved error or fault codes, the time display should now show the most recent error code.
How long does it take for a washer to exit diagnostic mode?
Note: If no buttons are pressed on the washer for 5 minutes the washer will exit the diagnostics mode.
How to clean a washer that won't run?
First, try giving it a good cleaning. Use a cotton swab dipped in rubbing alcohol to clean the latch and any contact points. This will remove the lint, dirt, and product build-up that may be interfering with the electrical circuit.
What causes water to back up in washer?
Be sure the washer's drain hose is not inserted too far down the standpipe. It should only be inserted about six to eight inches. A severe clog in the drainage line could also cause a back-up of drainage water that seeps back into the washer.
Why won't my dryer start?
The dryer will not start if the door latch is malfunctioning. It may just need to be cleaned to remove lint and residue so that full contact is achieved or it may need to be replaced. Clean it by dipping a cotton swab in rubbing alcohol and cleaning all the contact points.
Why is my washer accumulating water?
If the standing water is clear and clean, it is probably accumulating due to a failed inlet valve on the washer.
Is Whirlpool a Cabrio?
Whirlpool is a leading manufacturer of washers and dryers around the world including the Cabrio and the Du et models of washer and dryers. The Duet models are a popular line; however, as with any home appliance, there can be Duet washer and dryer problems and a need for repairs.
