
How to Fix a Broken Keurig
- Step 1. Unclog the Needle Before you clean your Keurig’s needle, make sure it’s been at least 30 minutes since your last...
- Step 2. Dislodge Clogs Inside the Keurig Unplug the machine and remove the water tank. Set it aside. Now, standing at a...
- Step 3. Dislodge Clogs in the Keurig Tube
How to unclog your Keurig?
Your Keurig Cleaning Checklist
- Clean and descale your Keurig
- Unclog your Keurig’s needles
- Remove internal Keurig clogs
Why is my Keurig not working?
Why won’t my Keurig brew?
- Verify Your Setup. You should make sure your Keurig is properly set up if it won’t brew. ...
- Reset Your Keurig. If your machine is working fine but your Keurig Won’t Brew?, it is time to reset. ...
- Clean Your Machine. Although this solution isn’t glamorous, it is necessary. ...
- Contact Customer Service. ...
How to clean a Keurig and fix a broken one?
- Longer than usual time to brew a cup of joe
- When you expect a full cup of coffee but the brewed batch only fills half of your cup
- Extra grounds or granules in your brewed cup
- Any unexpected, moldy or mildew-y smells
- Mineral buildup on visible parts of the machine
How to fix your Keurig if it stops brewing?
- Do a water only brew on your Keurig, and see if your Keurig is dispensing the right amount of water, check by using a measuring cup.
- Check to see if you are using a water filter inside your machine.
- Power off your machine fully and then unplug it.
- Clean up your Keurig’s needles, but be careful. Here is a in-depth guide on how to clean Keurig needles!

What would cause my Keurig to stop working?
If your Keurig won't brew, it may need to be reset. The settings could be off, or the water reservoir could be incorrectly attached. Your brewer might also need to be descaled, a cleaning process that removes mineral buildup from the tank and tubes.
Is it worth repairing a Keurig?
Like many companies, Keurig does not sell replacement parts. So with only a few limited possible ways to fix your machine, it's a hit or miss to know if it will survive. However these fixing either come cheap or at no cost at all, so it would be worth trying to fix it.
How do you unclog a Keurig machine?
Run a rinse cycle (or three). That's why you'll want to run a cycle or three of just water through your brewer. Fill the reservoir with water and don't add a K-Cup. Push the brew button and discard the water that comes out. Your Keurig Mini should now be fully unclogged and ready to brew.
How long do Keurigs usually last?
three to five yearsMost Keurig customers say that their machines typically last for three to five years. But here are some other signs that might let you when to replace your Keurig before then: Your coffee doesn't come out piping hot.
How do you fix a Keurig that won't brew?
0:102:45How to Fix KEURIG Coffee Maker that Stopped or Slow Brewing - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo now just take the paper clip and poke it up alongside of that needle and it'll go right up insideMoreSo now just take the paper clip and poke it up alongside of that needle and it'll go right up inside and it'll clear out any debris that's up in. There. You're now ready to brew a cup of coffee.
How do you tell if your Keurig is clogged?
6:379:16Unclog your Keurig machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then inspect this corner area right here where the tubing is if you press it and you see someMoreAnd then inspect this corner area right here where the tubing is if you press it and you see some movement chances are you have got a very clogged.
How do you fix a coffee maker that won't brew?
Check your power switch by turning it on and off to make sure the machine is getting power. If that doesn't work, check your home breaker box or plug something else that you know definitely works into space where your coffee maker is. If that isn't working either, it may be a problem with your plug.
Why is my Keurig not pouring a full cup?
Why Does My Keurig not Brew a Full Cup? If your Keurig® is not brewing full cup it may be caused by one of the following: The exit needle is clogged by coffee grounds, tea, or cocoa mix. Run a water-only cleaning cycle to free up any stuck particles.
How do you unclog a Keurig with vinegar?
Run a mix of equal parts water and white vinegar through the machine. Pour the solution into the reservoir, turn on the machine, press the cycle button, and allow the solution to drain into a cup. You may need to descale your Keurig multiple times depending on how dirty it is.
What do you do when your Keurig runs slow?
The most likely cause of a slow Keurig is a clog or calcium buildup, both of which are easy to fix yourself....Empty the water reservoir.Pour the descaling solution into the reservoir.Run a cleaning brew cycle.Let the machine sit for 30 minutes.Brew with water 10-12 times.
How do I drain my Keurig without disassemble?
Step 1: Brewer must be powered off but plugged in. Step 2: Place a mug on the Drip Tray to catch the water to be drained. Step 3: Check if there is water left in the Cold Water Reservoir. If so, lift the brewer handle to drain the water in the Cold Water Reservoir into the Hot Water Tank.
Who makes the Keurig coffee machine?
The Keurig is a single cup coffee brewing system manufactured by Keurig Dr. Pepper, formerly Keurig Green Mountain, along with the various K-Cup pods proprietary to the system.
When was the Keurig Mini Plus recalled?
This initiated several hacks and modifications by both pod manufacturers and consumers alike. In December of 2014, Keurig recalled around 7 million units of the Keurig Mini Plus (Models K10 and B31), which had the potential to spew boiling water from the machine causing a burn hazard.
When was the first Keurig brewing system released?
Keurig released their first brewing system, the B2000, in 1998. This machine was designed specifically for offices, as the creators John Sylvan and Peter Dragone initially sought to solve the problem of the stale office coffee pot.
When did Keurig introduce the B100?
In 2004, they managed to prototype a home use brewer, the B100, but to a more competitive market, as other companies had already jumped on the pod brewing train. In 2014, Keurig introduced the Keurig 2.0 line, which disabled use of the brewer if a 3rd party pod was detected.
How to fix a keurig leak?
How To Fix The Leakage From Your Keurig. If your coffee maker starts to leak, be it hot water or hot coffee, that could be a big problem. With proper care, your coffee machine will give you years of service and hundreds of cups of coffee. If it starts to leak, you must find a solution as soon as possible.
What to do if your keurig won't brew?
If your Keurig mini won’t brew, you may need to clean your machine fully, or do a full reset. The do a full reset on your Keurig mini, you will need to hold down the power button fully, then unplug the machine.
Why does my keurig coffee taste bad?
But, if your machine is clogged up, the older coffee grounds can build up, and little nasty bits of old coffee grounds and calcium can leak into your new coffee, which will effect the taste of your coffee.
What happens if your keurig water pipe is clogged?
If the water pipe is clogged, you can get a few nasty chunks into the coffee of the keg and cause it to cause problems. Now, stay calm and follow these Keurig troubleshooting tips to ensure that you do not cause any further problems with your coffee machine.
Why does my keurig keep shutting off?
Your heating mechanism may have fully shut off, which happens when water is not being pumped correctly through the brewer, and when this happens the heating device in the Keurig will shut off fully to prevent your coffee maker from overheating. So, the way to fix this is to reset your water reservoir.
How long does a keurig water filter last?
The cleaning filter in the Keurig water reservoir is designed to last at least 3 months, in some cases up to 5 years or even longer . If your Keurig does not pump water, you may have a problem if your water pump does not pump.
Why is my keurig not pumping water?
This is due to debris disrupting the KeURig’s water pumps, or failing to function or being pumped. Coffee grounds and minerals gather in your Keurig and clog it up, and you have a bad time.
How to fix a keurig coffee maker that isn't working?
When you’ve come to know that your Keurig coffee maker isn’t working, try troubleshooting. Run the machine several times using only water without the K-cup. Another effective remedy is clearing the coffee maker’s dispensing line with a paper clip. But only after you have turned off the Keurig and even unplugged it.
How to clean a keurig coffee maker?
Mix some vinegar with water and add this solution to the machine. Let it soak for around 45 minutes. You can even get a proper Keurig descaling solution if you wish. After those 45 minutes, flush out all the vinegar-water solution simply by cleansing the coffee maker with clean, fresh water.
Why is my keurig lens obstructed?
So maybe this laser is dirty or blocked, so it doesn’t read correctly. With time, the lens tends to become obstructed due to debris, coffee grounds, and coffee oils. It’s only natural for this to happen.
How to clean a keurig with a brim?
Start by filling the water tank of the Keurig machine till the brim. But first, switch off your coffee maker and unplug it. After filling it up, shake the water reservoir gently a few times. This helps in eliminating possible trapped air within the machine.
Why does my keurig coffee maker power down?
When the reservoir is not in place , meaning when the magnets between the Keurig body and reservoir are not in contact with each other , then it’s likely your coffee maker is going to power down. If none of this works, maybe the problem lies with a faulty cord.
How long does it take for a keurig to go off?
If your Keurig mini coffee maker is in a sedentary state for over 90 seconds, then it’s going to go off all by itself. Not many Keurig users know this. So you have to press the power on button for starting it again.
Why does my keurig leak water?
Here’s another common problem many Keurig users complain about on the internet. The dispensing issue mainly arises due to potential clog. This also explains why the coffee maker leaks water at the time of heating.
Is my Keurig worth fixing?
There is not a lot you can do to repair the home Keurig, but you can try a few things to get a little more life out of your unit. When it comes to Keurig, repair is sometimes easier said than done. Like many companies, Keurig does not sell replacement parts.
Where can I get my Keurig repaired?
There are coffee equipment repair shops in most major cities, or you can call Keurig at 1-866-669-8922.
How often should a Keurig be replaced?
Keurig states “On average, a Keurig coffee maker that is used daily has a lifespan of approximately 5 years. ”
What is the warranty on Keurig?
Keurig gives a 1-year warranty on the new equipment and 90 days on a certified refurbished Keurig. Make sure you register your purchase for ease of warranty. If your Keurig breaks down for any reason in under 1 year from purchase Keurig has been a 5-star example on dealing with warranty and in almost all cases will send you a new replacement.
What can void Keurig warranty?
Buyer beware! Read your warranty to know what you can and cannot do to your machine:
How to make your Keurig last longer
Stay with mainstream K-Cups. Don’t buy weird machines or weird capsules.
So my Keurigs dead – What one should I buy?
I do want to give you some guidance on your next Keurig purchase as there are a lot of excellent Keurig in the market right now.
How to remove silver top plate from keurig?
To remove the silver top plate of your Keurig from the black plastic body, you’ll need to flip your machine upside down and use a long-shafted tool like a flat-head screwdriver to pop three plastic clip hinges apart. These clips hold the top plate to the body and can’t be reached effectively without going in from the bottom.
How many screws are there in a keurig?
There are four screws surrounding the main water pump holding the rest of the bottom of the machine together. Remove these screws and the two holding the end of the water pump tubing. With these screws removed, the bottom of the Keurig can be slowly lifted off.
Can you remove the bottom of a keurig?
With the screws off, the bottom can be removed, except it’s got some wires holding on to the inside of the machine. To do any serious repairs inside the housing you will have to cut these wires while leaving enough room to repair your cuts when it comes time to put your Keurig machine back together.
Can Keurig machines be repaired?
But it’s possible. Still, shredding something down for recycling won’t ever be as sustainable as repairing the machine and using it for as long as possible. When it comes to Keurigs, though, repair is sometimes easier said than done. Like many companies, Keurig doesn’t sell replacement parts.
Where can I take my broken Keurig?
COFFEE MAKERS CAN BE RECYCLED! And your other small appliances can be recycled as well. Please DO NOT throw those things in the trash. Your local Goodwill store. Staples. The store where you bought your appliance. Home Depot. Best Buy. The manufacturer of your small appliance.
How long should a Keurig machine last?
A Keurig coffee maker should last about 3-5 years. Note that some Keurig machines work only with certain types of capsules or k-cups. Therefore, if the manufacturer stops producing those capsules, the machine will become useless more quickly.
What would cause my Keurig to stop working?
Your water pump isn’t functioning properly. The heating system inside is malfunctioning due to issues with the water pump. Calcium build-up or dried coffee grounds are clogging your Keurig causing malfunctions.
How do I get rid of the nasty taste in my Keurig?
The most effective way to descale the Keurig is to use vinegar; white vinegar is a disinfectant, deodorizer and acidic enough to dissolve most buildup inside the machine. Empty the water reservoir and fill it with 48 oz of white vinegar. Run the vinegar through the Keurig until the reservoir is empty.
Are Keurig cups bad for the environment?
Machines that depend on hard-to-recycle pods, such as Nespresso and Keurig systems, are awful for the environment: Recent research (PDF) conducted by a UK-based coffee brand found that, of the 39,000 capsules produced worldwide every minute, 29,000 of them end up in landfills.
How do I dispose of a coffee maker?
All City of Sydney residents who need to dispose of old and unwanted electronic and electrical equipment can visit a nearby recycling station, drop off items to our quarterly recycling event or book a pick-up. Almost all types of old and unwanted electronic and electrical equipment can be recycled.
How to reset a keurig?
If you’re not sure how to do a basic reset to fix the most common issues you encounter with Keurig brewers: Turn the machine off and unplug for several hours. Plug back the machine and run a test brew cycle. This should reset your Keurig.
Why is my keurig shutting down?
For instance, once you remove the water reservoir, you’ll have to make sure you’re placing it correctly, in other words, magnetic contacts on the reservoir should be in contact with the ones on the machine. If it’s not in its right place, Keurig will be shut down as it’ll not sense any reservoir for freshwater.
Why does my keurig have a short cup?
A short cup occurs when Keurig doesn’t brew the coffee size you selected. This might be due to a clogged needle (due to coffee grounds or cocoa mix), a machine requires cleaning or a water reservoir being removed while brewing.
Why is my keurig water cloudy?
You’ll notice, water gets cloudy as the scaling and debris are forced into the Keurig water reservoir, giving the turkey basket will all the debris from that part and makes it easier for the pump to push the water freely, and you’d brew your delicious cup of coffee.
Why does my keurig make a grinding noise?
There could be several reasons, but most likely it happens because of water scaling, debris build ups and interferes with the water pump.
Why does my keurig stop brewing coffee?
Here is how to make your Keurig fully functional when you face any of the most common problems: 1. Too much scales buildup blocking the internal pipes / debris clogging the water lines.
How long does it take for a keurig to heat up?
Keurigs usually take around 3 minutes for the initial preheating; if the process takes longer, possibly there’s something wrong with the machine. In this case, just unplug and plug back the machine to start the brewing process once again.
